Husqvarna Z 448 manual

Husqvarna Z 448
7.5 · 1
PDF manual
 · 244 pages
English
manualHusqvarna Z 448
The following conditions must be fullled before
the engine can be started:
The blade switch must be pressed downward
into the disengaged position.
The park brake must be applied, by having both
control levers in the outboard (park brake on)
position.
Both steering controls must be in the locked
(outer) neutral / parking brake position.

Starting the Engine

1. Sit on the seat.
2. Raise the mower deck to the transport
position by locking the lift pedal forward.
3. Push the blade switch down to disengage the
mower blades.
4. Move the steering controls outward to the
locked (outer) neutral / parking brake position.
5. Move throttle control to the middle position. If
the engine is cold, pull the choke control up.
6. Open the fuel tank valve.
7. Push in and turn the ignition key to the start
position.
IMPORTANT INFORMATION Do not run the
starter for more than ve seconds each time. If
the engine does not start, wait approximately
ten seconds before retrying.
8. When the engine starts, immediately release
the ignition key back to the run position.
Slowly push in the choke control knob, if it
was used to start a cold engine.
9. Set the engine speed with the throttle. Let
the engine to run at a moderate speed,
approximately mid throttle, for a short time
before use. USE FULL THROTTLE WHEN
MOWING (no choke).

Running

1. Move the steering controls in, out of the
neutral /parking brake position.
NOTE: The mower has an operator presence
system. If the engine is running and the
operator tries to leave the seat without rst
engaging the park brake, the engine will shut
o.
2. Release the foot pedal latch to lower the deck
to the set cutting height.
3. Move throttle control to full throttle.
4. Engage the mower deck by pulling the blade
switch up.
WARNING! Make sure that no one is
near mower when engaging blade switch.
5. Rotate the control levers inward and slowly
move both control levers slightly forward to
move forward in a straight line.

Stopping the Engine

1. Move the throttle to the minimum position
(tortoise symbol).
2. Move the steering controls outward.
3. Disengage the mower deck by pressing the
blade switch down.
4. Raise the mower deck by pressing the foot
pedals forward to the transport position.
5. Engage the park brake by moving the control
levers outward into the park brake position.
If the engine has been worked hard, let it to
idle at least 60 seconds and get to a normal
operating temperature before stopping. To
prevent fouling the spark plugs, avoid idling
the engine for longer periods.
6. Turn the ignition key to the stop position and
remove the key. Always remove the key when
leaving the mower to prevent unauthorized
use.
IMPORTANT INFORMATION Leaving the
ignition switch in a position than OFF will cause
the battery to be discharged.

Operating on Hills

Read the Safety Instructions Driving on Slopes
in the Safety section.
Use the slowest speed possible before starting
up or down hills.
18

OPERATION

View the manual for the Husqvarna Z 448 here, for free. This manual comes under the category lawnmowers and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Husqvarna Z 448 or do you need help? Ask your question here

Need help?

Do you have a question about the Husqvarna and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Husqvarna Z 448 is a lawnmower designed for residential use. It features a 48-inch cutting deck made of durable materials for long-lasting performance. The lawnmower is powered by a reliable engine that provides sufficient power for cutting grass effectively. With a hydrostatic transmission, the Husqvarna Z 448 offers smooth and effortless operation, allowing users to easily maneuver around obstacles in the yard. The lawnmower is equipped with comfortable seating and ergonomic controls for user convenience. It also has adjustable cutting heights to accommodate different grass lengths. The Husqvarna Z 448 is designed to provide a clean and precise cut, leaving the lawn looking well-maintained. Additionally, it has a compact design for easy storage when not in use. Overall, the Husqvarna Z 448 is a practical and efficient option for homeowners looking to maintain their lawn with ease.

General
BrandHusqvarna
ModelZ 448
Productlawnmower
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Husqvarna Z 448 below.

How short should I cut the grass?

When the grass is longer than 4.5cm, the grass should be cut. The ideal length is between 3 and 4.5cm.

How often should I cut the grass?

In the spring, the grass should be cut every week, while in the summer once every two weeks is sufficient.

Can I mow the lawn when the grass is wet?

You can, but the result is better in dry weather. When the grass is wet, grass clumps can easily form and clog the mower.

How do I engage the park brake on the Husqvarna Z 448 lawnmower?

To engage the park brake on the Husqvarna Z 448 lawnmower, follow these steps: 1. Stop the engine. 2. Remove the ignition key. 3. Ensure the park brake is engaged. 4. Avoid making any adjustments unless the engine is stopped and the ignition key is removed. 5. Be cautious when loading the machine onto a truck or trailer using ramps to prevent any potential injuries. 6. Remember that once the bypasses are engaged and the steering controls are moved to release the parking brake, the unit is free to roll and may cause harm. 7. Use extra care when operating the park brake to ensure safety for yourself and others. 8. Always refer to the operator manual for detailed instructions and safety precautions.

What should I do if the throttle is not responding on the Husqvarna Z 448 lawnmower?

If the throttle is not responding on the Husqvarna Z 448 lawnmower, follow these steps: 1. Check if the throttle control is not stuck or obstructed. 2. Inspect the throttle cable for any damage or disconnection. 3. Ensure that the throttle linkage is properly connected and functioning. 4. Verify that the throttle lever on the engine is moving freely. 5. Clean any debris or dirt around the throttle mechanism. 6. Lubricate the throttle cable and linkage if necessary. 7. If the issue persists, consult a professional for further inspection and repair.

Is the manual of the Husqvarna Z 448 available in English?

Yes, the manual of the Husqvarna Z 448 is available in English .

Is your question not listed? Ask your question here

No results