View the manual for the Hunter 44360 here, for free. This manual comes under the category thermostat and has been rated by 1 people with an average of a 5.9. This manual is available in the following languages: English. Do you have a question about the Hunter 44360 or do you need help? Ask your question here

The Hunter 44360 thermostat is a heating and cooling device that helps regulate the temperature in your home or office. It is designed to be user-friendly, with a large and easy-to-read digital display that shows the current temperature and settings. The thermostat is programmable, allowing you to set different temperature levels throughout the day to maximize comfort and energy efficiency. One of the key features of the Hunter 44360 is its ability to automatically adjust the temperature based on your preferred settings and the time of day. This not only ensures that you are comfortable at all times, but also helps save energy by reducing heating or cooling when it is not needed. The thermostat also has a filter indicator that reminds you when it is time to change your air filter, ensuring that your heating and cooling system operates at its best. Additionally, the Hunter 44360 has a simple and intuitive interface, making it easy to navigate through the various settings and modes. In terms of installation, the Hunter 44360 can be mounted on the wall or placed on a tabletop. It is compatible with most heating and cooling systems, including gas, oil, and electric systems. Overall, the Hunter 44360 thermostat offers a reliable and efficient solution for managing the temperature in your environment. Its programmable features, filter indicator, and user-friendly design make it a practical choice for both residential and commercial use.
| Brand | Hunter |
| Model | 44360 | 44360 |
| Product | thermostats |
| EAN | 0049694443601, 0496944436010 |
| Language | English |
| Filetype | Use and Care Manual (PDF), Instructions / Assembly (PDF), Installation Guide (PDF) |
| Product color | Beige |
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Hunter 44360 below.
The best place for the thermostat is the room where you spend the most time, in many cases the living room or kitchen. Place the thermostat about one and a half metres above the floor, not in the sun and not on an outside wall.
If your thermostat has a dead band, your installation is, as it were, 'at rest'. The thermostat only switches on when, for example, the difference deviates more than 2˚C from the set room temperature.
Most people find that the ideal room temperature is between 19 and 22 degrees Celsius.
To install the Hunter 44360 thermostat, follow these steps: 1. Before starting the installation, make sure to turn off the power to your heating and cooling system at the circuit breaker. 2. Remove the old thermostat from the wall by unscrewing the mounting screws and disconnecting the wires. Take note of the wire labels or take a picture for reference. 3. Install the mounting plate of the Hunter 44360 thermostat onto the wall using the provided screws. Ensure that the plate is level. 4. Connect the wires from your heating and cooling system to the corresponding terminals on the thermostat. Refer to the wire labels or the picture you took earlier. 5. Attach the thermostat to the mounting plate by aligning the pins and pressing it firmly into place. 6. Turn on the power to your heating and cooling system at the circuit breaker. 7. Follow the on-screen prompts on the thermostat to set the date, time, and desired temperature settings. 8. Test the thermostat by adjusting the temperature and verifying that your heating and cooling system responds accordingly. Congratulations! You have successfully installed the Hunter 44360 thermostat.
To program the Hunter 44360 thermostat, follow these steps: 1. Slide the system switch to either HEAT or COOL, depending on the system you want to program. 2. Press the Program button to enter Program mode. The LCD display will start flashing. 3. Set the program times in 10-minute increments. Use the arrow buttons to adjust the time. 4. Set the program temperature in increments of 1 degree Fahrenheit or Celsius. Use the arrow buttons to adjust the temperature. 5. After 15 seconds of inactivity during programming, the thermostat will return to Normal Display mode. 6. Note the AM/PM indicator when setting the program time. 7. If you want to exit Program mode at any time, press the Hold/Return button. By following these steps, you can easily program the Hunter 44360 thermostat to meet your desired heating or cooling schedule.
If the Hunter 44360 thermostat is not turning on, you can try the following steps to troubleshoot the issue: 1. Check the Heat/Cool function switch on the thermostat to ensure it is set to the desired position. 2. Wait for a few minutes, as there may be a delay of up to 4 minutes before the system turns on or off to protect the compressor. 3. Check the circuit breakers and switches to ensure that there is enough power to the system. 4. Replace the batteries in the thermostat. 5. If applicable, make sure the furnace blower door is closed properly. 6. If your system has 4 wires, ensure that the jumper wire is installed between the RC and RH terminals. If the thermostat display is not coming on or staying illuminated, you can try replacing the batteries. Please note that these troubleshooting steps are specific to the Hunter 44360 thermostat and can help resolve issues with it not turning on.
To change the temperature settings on the Hunter 44360 thermostat, follow these steps: 1. If you want to temporarily override the current program and adjust the temperature, press and hold the Up or Down button for one second to enter Manual Override mode. Release the button when the display flashes. 2. Use the Up or Down buttons to adjust the temperature setting as desired. If you want to permanently override all settings and adjust temperatures manually, follow these steps: 1. To change the temperature unit from Fahrenheit to Celsius, press and hold the Up button. 2. Use a paperclip to press the Reset button. 3. Continue to press the Up button, but release the Reset button when the LCD turns on. To reset the unit back to Fahrenheit, press only the Reset button. By following these steps, you can easily change the temperature settings on the Hunter 44360 thermostat to suit your preferences.
If the Hunter 44360 thermostat is not following the programmed schedule, you can try the following steps to troubleshoot the issue: 1. Check the batteries and battery connections to ensure they are properly installed and functioning. 2. Reset the thermostat by removing it from the wall plate and setting the HG/HE switch to the correct position. 3. If the display is erratic, reset the thermostat and reprogram your settings. 4. Ensure that the time is set properly to AM or PM and that the thermostat is not in permanent override mode. 5. Check that the day setting is correct. By following these steps, you can address common issues that may prevent the Hunter 44360 thermostat from following the programmed schedule.
Yes, the manual of the Hunter 44360 is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Hunter and is the answer not in the manual?
Question and answer
Number of questions: 9Flashing E rr in the window of the thermostat. Is it broken or need to be reprogrammed? I replaced the batteries
How long do the hunter 44360 thermostat last ours is over 10 years old
A number 2 is flashing on the screen. What does it mean?
How to change fro Celsius to fahrenheit
What does the blinking number 3 mean?
How to turn off vacation mode
How do I clear an ERR ?
How to take off vacation mode
No backlight