Humminbird HELIX 5 manual

Humminbird HELIX 5
8.5 · 17
PDF manual
 · 215 pages
English
manualHumminbird HELIX 5
197
Troubleshooting

TROUBLESHOOTING

B
efore contacting Humminbird Customer Service, please read the following section. Taking the time to review these troubleshooting
g
uidelines may allow you to solve a performance problem yourself, and therefore avoid sending your unit back for repair.

Control Head Doesn’t Power Up

If your control head doesn’t power up, use the installation guide to confirm the following:
the power cable is properly connected to the control head
the power cable is wired correctly, with red to positive battery terminal and black to negative terminal or ground
the fuse is operational
the battery voltage of the power connector is at least 12.2 Volts
Correct any known problems, including removing corrosion from the battery terminals or wiring, or replacing the battery if necessary.
Also, visit humminbird.com to download our Power Troubleshooting Guide.

Control Head Doesn’t Detect the Connected Transducer

A connected and functioning transducer will automatically be detected by the control head. The control head will default to the
transducer that was included with your unit and automatically select sonar settings based on the transducers capabilities. If, when
you power up the control head, it does not automatically select sonar settings or display sonar data, even though a transducer is
already connected, this means that the control head is not detecting the transducer. Perform the following troubleshooting tasks:
Using the transducer installation guide, check to make sure that the transducer cable is securely connected to the control head.
Reconnect if necessary, and power up the unit again to see if this fixes the problem.
Replace the non-functioning transducer with a known good transducer if available and power up the control head again.
Check the transducer cable. Replace the transducer if the cable is damaged or corroded.

Control Head Doesn’t Detect a Connected Accessory

A connected and functioning accessory will automatically be detected by the control head. If you connected an accessory to the
control head and the accessory is not detected by the control head, try the following:
Check to make sure that the accessory cable is securely connected to the control head. Reconnect the cable, if necessary.
Confirm the accessory is connected to a stable and reliable power source.
Entire System Restart: Power off all control heads and connected equipment. Wait 10 seconds, and then power on all equipment.

View the manual for the Humminbird HELIX 5 here, for free. This manual comes under the category fish finders and has been rated by 17 people with an average of a 8.5. This manual is available in the following languages: English. Do you have a question about the Humminbird HELIX 5 or do you need help? Ask your question here

Need help?

Do you have a question about the Humminbird and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 34
R
Rick September 6, 2022

Does basic helix 5 g2 have fish id ?

1 comment
E
Emma of manua.lsOctober 24, 2023

Yes, the Humminbird HELIX 5 fish finder (model number 1435440) includes a feature called Fish ID. Fish ID+ utilizes advanced signal processing to interpret sonar returns and show fish symbols on the Sonar View when certain conditions are met. You can enable or disable Fish ID+ in the Sonar settings menu. When Fish ID+ is enabled, fish symbols will be displayed on the Sonar View, with the color of the symbols indicating the location of the sonar beam. The depth of the fish is also shown above the symbol. You can adjust the sensitivity for fish detection and receive alerts with the Fish ID Alarm enabled. To adjust the Fish ID sensitivity, go to the Sonar settings menu and select Fish ID Sensitivity. To activate the Fish ID Alarm, go to the Alarms settings menu and select Fish ID Alarm.

This answer is automatically generated
M
MICHAEL YOQUELETJune 9, 2022

helix x 5 di g2 how to use Iam disappoint try to set it up i have try every thing,

M
MichaelJuly 3, 2023

We just got a new boat with the hummingbird helix5. The depth finder is way off it is showing 300 feet to 1200 for our lake that is 50 feet at the deepest. Is there a way to reset it. The lake has a lot of shallow areas and it would be good to have it as a backup until we learn lake better

W
Wayne BoyleJuly 12, 2023

What is the part number for the Helix 5 depth/fish finder. Also where can I order a replacement from.

P
Pedro SantosAugust 8, 2023

Hi I have a Helix5.DI-GPS, s/n 15050603. I need to have units in meters but the menu only alow Ft and Fathoms, Its possible to have units in meters? Best rgds

K
Kenneth MihokJune 5, 2024

How do I clear old info from helix 5

T
Tim staats September 11, 2023

My brother and I just bought a brand new hummingbird Helix 5 installed in the boat went through all the setup everything works fine on it everything except it won't find a fish it won't murder fish everything else on it works perfect just won't find a fish look at that big

H
Heinz Karl SyrchJune 12, 2024

my fish finder section has goin blank the GPS works fine

E
EuiAugust 5, 2022

My display is in Russian. How do I scroll to a screen and change into English?

My display is in Russian. 
How do I scroll to a screen and change into English?
zoom-in
View photo
1 comment
A
Ashley AlexanderAugust 8, 2023

On start up the pic of the hummingbird comes up then that’s all pulled the power plug for 30 minutes still doing it

M
MiltAugust 16, 2022

I cannot get the menu to change from normal to advanced on my helix five chirp GPS G2

The Humminbird HELIX 5 is a fish finder device that offers advanced features for an enhanced fishing experience. This fish finder is designed to provide accurate and detailed information about underwater structures, depth, and fish location. The HELIX 5 features a high-resolution color display that allows for easy viewing of sonar readings, even in bright sunlight. With its precision internal GPS, this fish finder can quickly and accurately determine your current position and mark waypoints for future reference. Equipped with DualBeam PLUS sonar technology, the HELIX 5 provides a wide coverage area and detailed images of the underwater environment. The device operates at frequencies of 200 kHz and 83 kHz to deliver clear and reliable sonar readings. With its built-in UniMap cartography, the HELIX 5 offers detailed maps of various bodies of water, including rivers, lakes, and coastlines. This feature allows you to locate specific areas, navigate accurately, and identify potential fishing spots. The Humminbird HELIX 5 is also equipped with advanced sonar features such as SwitchFire, which allows you to customize your sonar return appearance according to your fishing preferences. Additionally, it has CHIRP sonar technology, which provides even more detailed images and enhanced target separation. The device is built with durable materials, ensuring its reliability and longevity. Its intuitive interface and user-friendly controls make it easy to use for both beginners and experienced anglers. In conclusion, the Humminbird HELIX 5 is a versatile fish finder that offers advanced features, accurate sonar readings, and detailed maps. It provides an invaluable resource for anglers of all skill levels, helping them locate fish and improve their fishing efficiency.

General
BrandHumminbird
ModelHELIX 5 | 409590-1
Productfish finder
EAN0082324048999, 0641676165848, 0974566059195
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Humminbird HELIX 5 below.

How can I adjust the sensitivity on my Humminbird HELIX 5 fish finder?

Use the sensitivity control to adjust the strength of the sonar signal to optimize the display for your fishing conditions. Start with a lower sensitivity and gradually increase it until you get a clear and detailed view of the underwater environment.

How do I interpret the sonar returns on my Humminbird HELIX 5?

The sonar returns appear as colored or grayscale images on the screen. Fish are usually represented as arches or fish icons, while structure and bottom contours are displayed as lines or various shapes. Refer to the color palette legend provided to understand the representation of different sonar returns.

What do I need to do if my fish finder is not turning on?

Firstly, check if the power cable is securely connected to the fish finder and the power source. Ensure that the power source is turned on and supplying electricity. If the issue persists, check the fuse in the power cable for any damages or try connecting the fish finder to a different power source.

How do I adjust the display settings on my Humminbird HELIX 5?

Navigate to the menu options and locate the Display settings. Here, you can adjust the brightness, contrast, color palette, and other visual settings to enhance the readability of the screen. Experiment with different settings to find the best configuration for your specific fishing environment.

How can I troubleshoot if my Humminbird HELIX 5 is not providing accurate depth readings?

Start by ensuring the transducer is properly installed and fully submerged in water. Check if any vegetation or debris is obstructing the transducer. If everything seems normal, navigate to the Sonar settings and perform a manual depth calibration to ensure accurate depth readings.

Is the manual of the Humminbird HELIX 5 available in English?

Yes, the manual of the Humminbird HELIX 5 is available in English .

Is your question not listed? Ask your question here

No results