Hori NSW-118E manual

Hori NSW-118E
7.8 · 1
PDF manual
 · 1 page
English
manualHori NSW-118E
Thank you for purchasing this product.
Before using this product please read the instructions carefully.
After reading the instruction manual, please keep it for reference.

Instruction manual

● Keep this product out of the reach of children under 3.
● Choking Hazard.
● Keep the controller away from dusty or humid areas.
● Do not use this product if damage or alteration occurs.
● Do not get wet.
● Do not leave in hot environment for a long time.
● Do not touch the metal parts of USB plug.
● Do not apply strong impact or weight on the product.
● Do not pull roughly or bend the cable of the controller.
● Never disassemble, repair or modify this product.
● If product needs cleaning, use only a soft dry cloth.
  Do not use any chemical agents like benzine or thinner.
● Do not use this product for anything other than its
  intended purpose.
  We are not responsible for any accidents or damages
  in the event of use other than the intended purpose.
Caution
Controller:  × 1 Instruction manual:  × 1
Included
Layout
TURBO LED
USB Connector
ZR Button
Left Stick
(Functions as a button when
pressed down.)
Control Pad
Capture Button
TURBO Button
HOME Button
Controller cable
Right Stick
(Functions as a button when
pressed down.)
B Button
A Button
X Button
Y Button
-
Button
+ Button
L Button ZL Button R Button
Nintendo Switch
TURBO LED
USB Connector
RB Button
Left Stick
(Functions as a button when
pressed down.)
Control Pad
No function
TURBO Button
GUIDE Button
Controller cable
Right Stick
(Functions as a button when
pressed down.)
B Button
A Button
X Button
Y Button
BACK Button
START Button
LT Button LB Button
RT Button
PC
To Nintendo Switch
TM
Dock USB port.
Please insert the USB connector of the controller into the USB port of the Nintendo Switch
TM
Dock.
How to connect
Main Features
■ Dimensions : 4.0 in (W) x 5.5 in (D) x 2.7 in (H)
■ Cable length : 9.8 ft■ Weight : 0.5 lbs
■ Rating : 5V 45mA
Nintendo Switch
TM
/ PC(Xinput)
Platform
Windows
®
10
8
8.1
7
Supported OS
USB Port, Internet ConnectionSystem requirements
Important
* This product is not a wireless controller.
* Do not use the Turbo Function in the HOME Menu.
Make sure that your Nintendo Switch
TM
is updated with the latest system software.
The Turbo hold function allows continuous rapid ire without having to hold the button.
(Pressing the assigned button deactivates this).
* Control Pad (UP, DOWN, LEFT or RIGHT) are not compatible with the Turbo hold mode,
and can only be used to set Turbo mode.
The following buttons can be set to Turbo or Turbo hold mode:
A Button / B Button / X Button / Y Button / L Button / R Button / ZL Button / ZR Button /
Control Pad (UP / DOWN / LEFT / RIGHT)
How to use the Turbo Functions
+
TURBO Button
+
TURBO Button
Turbo OFF
* The Turbo LED flash rate corresponds to the Turbo speed and will flash as long as one of the button is in Turbo mode.
* By pressing the HOME Button, all Turbo function and Turbo hold settings will be deactivated.
When restarting game play, you will need to set the Turbo function again.
* Turbo Function may not be compatible with all software titles. Please try adjusting the Turbo settings or simply turn OFF TURBO.
* Turbo function will deactivate when you unplug the USB connector.
Turbo IndicatorSetting method
Turbo Mode
OFF
(All buttons)
Hold down the Turbo button and
then press the button that you
want to set to Turbo mode.
+
TURBO Button
Turbo Hold
Press the button once more,
and the button will remain
in Turbo (Turbo Hold).
Pressing the button again
once more will deactivate
the Turbo function.
Hold the TURBO Button and
press the SELECT Button.
OFF
OFF
Button OFF
TURBO LED will lash.
Green or Orange
Button ON
TURBO LED will turn on.
Green or Orange
Button OFF
TURBO LED will turn on.
Green or Orange
Button ON
TURBO LED will lash.
Green or Orange
+
TURBO Button
-
Button
In the case that after deactivating the turbo
function, the turbo Indicator LED does not
turn off, this means that there is still a button
set to Turbo/Turbo Hold.
※ LED will turn red while L/R and ZL/ZR button
  functions are switched.
If you forget which buttons you have set to
Turbo mode, deactivate them all and reassign,
as you require.
※ LED will turn red while L/R and ZL/ZR button
  functions are switched.
You can adjust the Turbo mode to 3 different speeds.
While pressing the Turbo Button, push up on the Right Analog Stick
to change the Turbo speed in the following order :
5 times/second → 10 times/second → 20 times/second
While pressing the Turbo Button, push down on the Right Analog Stick
to change the Turbo speed in the following order :
20 times/second → 10 times/second → 5 times/second
How to change Turbo Speed
+
+
* Turbo speed is set to 10 times/second by default.
* Right Stick must be returned to the neutral position before changing to the next turbo speed.
* The Turbo LED will lash at a rate corresponding to the Turbo speed for 2 seconds.
US
Warranty
HORI warrants to the original purchaser that the product purchased new in its original packaging shall be free of any defects
in material and workmanship for a period of 90 days from the original date of purchase. If the warranty claim cannot be
processed through the original retailer please address directly to HORI at infous@hori.jp.
Please visit http://stores.horiusa.com/policies/ for warranty details.
PRODUCT DISPOSAL INFORMATION
Where you see this symbol on any of our electrical products or packaging, it indicates that the relevant
electrical product or battery should not be disposed of as general household waste in Europe.
To ensure the correct waste treatment of the product and battery, please dispose of them in accordance
with any applicable local laws or requirements for disposal of electrical equipment or batteries. In so doing,
you will help to conserve natural resources and improve standards of environmental protection in treatment
and disposal of electrical waste. Applicable to EU countries only.
THE FCC WANTS YOU TO KNOW
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with theinstructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipmentoff and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
EU
Warranty
For all warranty claims made within the irst 30 days after purchase, please check with the retailer where the original
purchase was made for details. If the warranty claim cannot be processed through the original retailer or for any other
inquiries pertaining to our products, please address directly to HORI at infoeu@hori.jp.
Please retain contact information for future reference.
The image on the package may differ from the actual product.
The manufacturer reserves the right to change the product design or speciications without notice.
The wires are not to be inserted into socket-outlets.
The packaging must be retained since it contains important information.
HORI & HORI logo are registered trademarks of HORI.
The normal function of the product may be disturbed by strong electro-magnetic interference.
If so, simply reset the product to resume normal operation by following the instruction manual (How to connect).
In case the function does not resume, please relocate to an area which does not have electro-magnetic interference
to use the product.
Switch functions between L/R and ZL/ZR buttons.
* Setting will remain even after you unplug or turn the power off.
* Repeat the process to reset the button settings.
* Buttons will switch when you turn on the Nintendo Switch while the USB is plugged and ZL/ZR buttons are simultaneously pressed.
How to switch
L/R to ZL/ZR Toggle Function
L Button
ZL Button
R Button
ZR Button
TURBO LED will turn off.
TURBO LED (RED) will turn on.
L Button
ZL Button
R Button
ZR Button
Press and hold the ZL and ZR buttons simultaneously and connect the USB connector to
the Nintendo Switch
TM
Dock USB port.
To Nintendo Switch
TM
Dock USB port.
+

Manual

View the manual for the Hori NSW-118E here, for free. This manual comes under the category Controllers and has been rated by 1 people with an average of a 7.8. This manual is available in the following languages: English. Do you have a question about the Hori NSW-118E or do you need help? Ask your question here

Need help?

Do you have a question about the Hori and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Samsung Galaxy A7 owners to provide you with a good answer.

Asbyx • 7-2-2021 No comments

Hi, I have my controller since a year or more now, it has been working properly since yesterday. It works fine on my computer but my Nintendo Switch isn’t able to recognize it... I connect the controller to the dock but nothing happens. The controller is on, the red LED is on since I am swapping the ZR and R buttons but the switch doesn’t detect it. Any solutions ?

Answer this question

Number of questions: 1

Hori NSW-118E specifications

Below you will find the product specifications and the manual specifications of the Hori NSW-118E.

General
Brand Hori
Model NSW-118E
Product Controller
EAN 4961818029675
Language English
Filetype PDF
Input device
Device type Gamepad
Gaming platforms supported Nintendo Switch
Gaming control technology Analogue
Gaming control function buttons Home button,Start button,Turbo button
Shoulder buttons
Buttons quantity 16
Ports & interfaces
Connectivity technology Wired
Device interface USB
Power
Input voltage 5 V
Input current 0.045 A
Ergonomics
Product colour Blue,Red,White
Cable length 3 m
Ergonomic grip
Plug and Play
LED indicators
Weight & dimensions
Width 102 mm
Depth 140 mm
Height 69 mm
Weight 226 g
Packaging content
Manual
Number of products included 1 pc(s)
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Hori NSW-118E below.

Is your question not listed? Ask your question here

No results