Honeywell VAM manual

Honeywell VAM
9.2 · 1
PDF manual
 · 40 pages
English
manualHoneywell VAM
10
Adding (Include/Add) Z-Wave Devices
Each device must be installed according to the manufacturer’s instructions.
Before starting, make sure each device is installed and functioning
properly.
WARNING: Automation is intended for lifestyle convenience. Do not use
automation for life safety and property protection.
1. Go to the Z-Wave Device Management screen (Automation > Z-Wave
Setup).
2. Press Add Device.
3. At the Z-Wave device, press the appropriate Function key, depending on
the type of device being added. Refer to the device installation sections
that follow:
A. Light, Switch or Outlet Devices
i. Perform steps 1 & 2 above.
ii. Be sure the power switch on the device module is ON.
iii. Press the Function Key on the device.
NOTE: Z-Wave light modules may vary; follow the instructions in the
User’s Guide for your specific device to include properly.
If a dimmer module (multi-level switch) was included, three
lighting level icons (Low, Mid, High) are displayed.
If an on/off light/appliance module (binary switch) was included,
an On/Off icon (to control the device) is displayed.
The screen displays a series of messages:
“Start add device. Please press function key on device”
“Adding Slave Unit”
Device added successfully”
B. Door Locks and Garage Door Control Devices (Entry Controller)
IMPORTANT: Be sure the door lock orientation/handedness is
correct before including the lock into the system.
NOTE: The VAM cannot synchronize panel users to the lock.
Door locking devices may vary; follow the instructions in the devices
User Guide for your specific door lock to include properly and to
program a new user code. Refer to the Door Lock’s Instruction Guide
and connect necessary cables, then install batteries.
Include a door lock device into VAM as follows:
i. Perform steps 1 & 2 above.
ii. Press the Function Key on the door lock.
The screen displays a series of messages:

Manual

View the manual for the Honeywell VAM here, for free. This manual comes under the category smart home and has been rated by 1 people with an average of a 9.2. This manual is available in the following languages: English. Do you have a question about the Honeywell VAM or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Honeywell and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 1
D
Dave NuckollsFebruary 1, 2022

After power loss restored, wall light switch isn't working. Flashing Blue Light

Honeywell VAM specifications

Below you will find the product specifications and the manual specifications of the Honeywell VAM.

General
BrandHoneywell
ModelVAM | VAM
Productsmart home
LanguageEnglish
FiletypeUser manual (PDF)
Weight & dimensions
Width209.6 mm
Height152.4 mm
Depth12.7 mm
Ports & interfaces
Connectivity technologyWireless
Wi-FiYes
Ethernet LAN-
Z-WaveYes
USB ports quantity0
Design
Product colorBlack
Control typeButtons, Touch
Display
Built-in displayYes
Power
Input voltage12 V
Performance
Mobile operating systems supportedAndroid, iOS
CompatibilityVISTA, Z-Wave devices, IP cameras
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Honeywell VAM below.

What is the height of the Honeywell VAM?

The Honeywell VAM has a height of 152.4 mm.

What is the width of the Honeywell VAM?

The Honeywell VAM has a width of 209.6 mm.

What is the depth of the Honeywell VAM?

The Honeywell VAM has a depth of 12.7 mm.

Is the manual of the Honeywell VAM available in English?

Yes, the manual of the Honeywell VAM is available in English .

Is your question not listed? Ask your question here

No results