Honeywell RTH9585WF1004 manual

Honeywell RTH9585WF1004
9.3 · 8
PDF manual
 · 76 pages
English
manualHoneywell RTH9585WF1004
M34540
C
K
Rc
R
W-
O/B
Y
G
W2-
Aux/E
Y2
L
W
Y
G
R
C
Quick Start Guide
Smart Color Touchscreen Programmable ThermostatRTH9585WFSearch for local rebates: HoneywellHome.com/Rebates
Install your thermostat.
Connect your home Wi-Fi network.
Register online for remote access.
1
2
3
Welcome
Getting set up and ready is simple. Read before installing.
This thermostat works with common 24 volt
systems such as forced air, hydronic, heat
pump, oil, gas, and electric. It will not
work with millivolt systems, such as a gas
fireplace, or with 120/240 volt systems such
as baseboard electric heat.
1.1 Switch OFF power to your heating/cooling system
1.1a Important! To protect your
equipment, switch OFF the
power to your heating/
cooling system at the
breaker box or the system
switch.
1.1b Confirm power is OFF.
Try to turn on heating/
cooling equipment by
changing temperature
on your old thermostat.
Your power is OFF if your
system does not turn ON.
Install your thermostat
1
Circuit
breaker
box
Heating/
cooling system
power switch
C
M33823A
Terminal designation
If you have an older thermostat with a
sealed mercury tube, see warning page
for proper disposal instructions.
1.2 Remove old thermostat faceplate and leave wires connected 1.2a Take a picture of the wire connections for later reference. 1.2b If no wire is connected to a terminal labeled C or no C terminal exists on the old thermostat, view the Alternate Wiring videos at wifithermostat.com/videos
Important! C wire is required
and is the power source for your
thermostat. Without a C
wire, your thermostat will
not power up.
1.3 Label wires Do not label by wire color.
Use the supplied sticky tags to label
each wire as you disconnect it. Label
wires according to old thermostat
terminal designations, not by wire
color.
Note: If no tag matches a terminal
designation, write the appropriate
letter on a blank sticky tag.
Note: Wrap the wires around a pencil
to prevent them from falling back into
the wall.
1.4 Remove wallplate
Remove the old wallplate from
the wall after all wires are
labeled and disconnected.
Blank tagsSticky tagTerminal designation
M31537
C
C
M31545
1.5 Mount wallplate for thermostat
Mount your new wallplate using
screws and anchors included
with the thermostat.
If necessary:
Drill 3/16-in holes for drywall
Drill 7/32-in holes for plaster
Note: You may be able to use
your existing wall anchors. Hold
the wallplate up to the existing
anchors to check for alignment.
M34499
LEVEL
HERE
R
Y
C
W
G
C
K
Rc
R
W-
O/B
Y
G
W2-
Aux/ E
Y2
L
Wallplate1.6 Connect wires
Important! C wire is required and
is the power source. Without a C wire,
your thermostat will not power up.
See the C Wire Addendum document for more information.
View the Alternate Wiring videos
at wifithermostat.com/videos
1.6a Starting with the C Wire, match
the sticky tag on the wire to the
terminal labels.
1.6b Straighten wire and gently slide
into terminal hole until it clicks
into place. (If you need to
remove a wire, use a pen tip to
press the terminal release and
then pull the wire out.)
Note: Refer to the wiring picture
you took in Step 1.2.
Tip: To make it easier to slide the
wire into place, use a pen tip to
hold down the terminal release.
Note: The wiring for your
application might be different
than the wiring shown below.
Labels don’t match or have
heat pump system?
See User Guide.
Labels don’t match or have
heat pump system?
See User Guide.
1.7 Attach thermostat to wallplate Align the thermostat with
wallplate and snap into
place.
Before you beginThermostatWallplate
LEVEL
HERE
M34498A
1.8 Switch heating/cooling system ON Important! 1.8a Verify that the C wire is
connected at the thermostat
and at the heating/cooling
system.
1.8b Make sure the heating/
cooling system door is
firmly secured.
1.8c Switch power back ON for
your heating/cooling system
at the breaker box or its
power switch.
Turn over
or
M31535
1.6c In the image on the right, check
the box next to each connection.
You will use this checklist in
Step 1.9.
1.6d Verify wire is firmly secured by
gently pulling on wire.
1.6e Repeat steps a–d for all other
wires.
1.6f Push any excess wire back into
the wall opening after all wires
are installed.
Note: The L terminal on the lower right is used only for Heat Pump systems.Note: If the old thermostat for Heat Pump System has separate wires on Aux and E, use a wire nut to attach both wires to a separate wire. Slide this third wire into the W2-Aux/E terminal.Terminal release
Circuit
breaker
box
Heating/
cooling system
power switch
or
M31535
View the installation video
at wifithermostat.com/
support
You will also need:
Small screw driver
• Pen
Your home WiFi
network password
You will need your
camera to take a
picture of your old wire
connections.
Note: You will need a
picture of your wire
connections to wire
the new thermostat.
Remove jumper loop ONLY if you have both R and Rc wires.
Important!
Check the box for each wire
you connect. You will need
this information in Step 1.9.
C
K
Rc
R
W-O/B
Y
G
W2-
Aux/E
Y2
L
EXAMPLE WIRING
Yours may look different
Resideo Inc., 1985 Douglas Drive North,
Golden Valley, MN 55422
33-00268—05 M.S. Rev. 04-22 | Printed in United States
© 2022 Resideo Technologies, Inc. All rights reserved. The Honeywell Home trademark is used under license from Honeywell International, Inc.
This product is manufactured by Resideo Technologies, Inc. and its affiliates.
www.resideo.com
Electrical Ratings
Terminal Voltage (50/60Hz) Max. Current Rating
W-O/B 2030 Vac 1.0 A
W2 (Aux/E) 2030 Vac 1.0 A
Y Cooling 2030 Vac 1.0 A
Y2 Cooling 2030 Vac 1.0 A
G Fan 2030 Vac 0.5 A
33-00268-05
M38031A
HOME FAN
MODE
SETTINGS
SET TO
INDOOR
54% Humidity
FOLLOWING SCHEDULE
OUTDOOR
55% Humidity
Cool On
6:30 pm
74
°
72
°
72
°

View the manual for the Honeywell RTH9585WF1004 here, for free. This manual comes under the category thermostat and has been rated by 8 people with an average of a 9.3. This manual is available in the following languages: English. Do you have a question about the Honeywell RTH9585WF1004 or do you need help? Ask your question here

Need help?

Do you have a question about the Honeywell and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 211
C
ConnieJune 3, 2023

How do you remove the cover on the Honeywell RTH9585WF from the wall plate. Does it just snap on & off?

K
Kenneth August 20, 2023

After installing air conditioning why does the thermostat say updating system

P
Philip ScottSeptember 19, 2023

how to change temperature setting from Fahrenheit to Celsius

The Honeywell RTH9585WF1004 thermostat is a home heating and cooling device designed to provide efficient climate control. This thermostat features a sleek and modern design that can seamlessly blend with any interior decor. Its Wi-Fi capability allows users to control their home's temperature remotely using their smartphone, tablet, or computer. The Honeywell RTH9585WF1004 thermostat is specifically designed to be compatible with the majority of heating and cooling systems, including heat pumps, gas furnaces, and electric heating systems. It offers a user-friendly interface with a customizable color touchscreen display, making it easy to navigate and adjust settings. With its advanced programming capabilities, this thermostat can create a personalized schedule to optimize energy usage and save on utility bills. It also has a Smart Response feature that learns the preferred temperature settings and adapts accordingly. The Honeywell RTH9585WF1004 thermostat has intelligent alerts that notify users about various system issues, such as filter changes or maintenance requirements. It is equipped with geofencing technology, which allows the thermostat to automatically adjust the temperature based on the occupants' location. This thermostat also has voice control compatibility, allowing users to adjust temperature settings using popular voice assistants, such as Amazon Alexa or Google Assistant. Overall, the Honeywell RTH9585WF1004 thermostat provides reliable and convenient climate control for homes, with its user-friendly interface, energy-saving features, and compatibility with a wide range of heating and cooling systems.

General
BrandHoneywell
ModelRTH9585WF1004 | RTH9585WF1004
Productthermostats
EAN0085267911313
LanguageEnglish
FiletypeUser manual (PDF), Quickstart Guide (PDF), Installation Guide (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Honeywell RTH9585WF1004 below.

Where is the best location to place the thermostat?

The best place for the thermostat is the room where you spend the most time, in many cases the living room or kitchen. Place the thermostat about one and a half metres above the floor, not in the sun and not on an outside wall.

What is the dead band of a thermostat?

If your thermostat has a dead band, your installation is, as it were, 'at rest'. The thermostat only switches on when, for example, the difference deviates more than 2˚C from the set room temperature.

What is the ideal room temperature?

Most people find that the ideal room temperature is between 19 and 22 degrees Celsius.

How do I connect my Honeywell RTH9585WF1004 thermostat to my Wi-Fi network?

Simply go to the thermostat settings menu, and select the "Wi-Fi Setup" option. Follow the on-screen prompts to connect the thermostat to your Wi-Fi network.

How do I adjust the temperature setpoints on my thermostat?

Press the "Up" or "Down" arrow buttons on the thermostat's display to adjust the temperature setpoint to your desired level. The changes will be saved automatically.

What should I do if my thermostat is not responding to my commands?

Firstly, ensure that the thermostat is powered on. If it is, try resetting it by pressing the "Menu" button, then selecting "Preferences," and finally choosing "Restore Factory Defaults." If the issue persists, you might need to check the wiring connections or contact customer support for further assistance.

How can I program a schedule on my Honeywell RTH9585WF1004 thermostat?

Press the "Menu" button, select "Program," and then choose "Schedule." From there, you can set different temperature settings for various times of the day. Make sure to save your changes once you've finished programming the schedule.

Can I control my thermostat remotely using my smartphone?

Absolutely! Download and install the Honeywell Home app on your smartphone, create an account, and then follow the app's instructions to pair it with your thermostat. Once paired, you can control and adjust your thermostat from anywhere as long as you have an internet connection.

Is the manual of the Honeywell RTH9585WF1004 available in English?

Yes, the manual of the Honeywell RTH9585WF1004 is available in English .

Is your question not listed? Ask your question here

No results