Honeywell RTH9585WF1004 manual

Honeywell RTH9585WF1004
9.3 · 8
PDF manual
 · 76 pages
English
manualHoneywell RTH9585WF1004
M34540
C
K
Rc
R
W-
O/B
Y
G
W2-
Aux/E
Y2
L
W
Y
G
R
C
Quick Start Guide
Smart Color Touchscreen Programmable ThermostatRTH9585WFSearch for local rebates: HoneywellHome.com/Rebates
Install your thermostat.
Connect your home Wi-Fi network.
Register online for remote access.
1
2
3
Welcome
Getting set up and ready is simple. Read before installing.
This thermostat works with common 24 volt
systems such as forced air, hydronic, heat
pump, oil, gas, and electric. It will not
work with millivolt systems, such as a gas
fireplace, or with 120/240 volt systems such
as baseboard electric heat.
1.1 Switch OFF power to your heating/cooling system
1.1a Important! To protect your
equipment, switch OFF the
power to your heating/
cooling system at the
breaker box or the system
switch.
1.1b Confirm power is OFF.
Try to turn on heating/
cooling equipment by
changing temperature
on your old thermostat.
Your power is OFF if your
system does not turn ON.
Install your thermostat
1
Circuit
breaker
box
Heating/
cooling system
power switch
C
M33823A
Terminal designation
If you have an older thermostat with a
sealed mercury tube, see warning page
for proper disposal instructions.
1.2 Remove old thermostat faceplate and leave wires connected 1.2a Take a picture of the wire connections for later reference. 1.2b If no wire is connected to a terminal labeled C or no C terminal exists on the old thermostat, view the Alternate Wiring videos at wifithermostat.com/videos
Important! C wire is required
and is the power source for your
thermostat. Without a C
wire, your thermostat will
not power up.
1.3 Label wires Do not label by wire color.
Use the supplied sticky tags to label
each wire as you disconnect it. Label
wires according to old thermostat
terminal designations, not by wire
color.
Note: If no tag matches a terminal
designation, write the appropriate
letter on a blank sticky tag.
Note: Wrap the wires around a pencil
to prevent them from falling back into
the wall.
1.4 Remove wallplate
Remove the old wallplate from
the wall after all wires are
labeled and disconnected.
Blank tagsSticky tagTerminal designation
M31537
C
C
M31545
1.5 Mount wallplate for thermostat
Mount your new wallplate using
screws and anchors included
with the thermostat.
If necessary:
Drill 3/16-in holes for drywall
Drill 7/32-in holes for plaster
Note: You may be able to use
your existing wall anchors. Hold
the wallplate up to the existing
anchors to check for alignment.
M34499
LEVEL
HERE
R
Y
C
W
G
C
K
Rc
R
W-
O/B
Y
G
W2-
Aux/ E
Y2
L
Wallplate1.6 Connect wires
Important! C wire is required and
is the power source. Without a C wire,
your thermostat will not power up.
See the C Wire Addendum document for more information.
View the Alternate Wiring videos
at wifithermostat.com/videos
1.6a Starting with the C Wire, match
the sticky tag on the wire to the
terminal labels.
1.6b Straighten wire and gently slide
into terminal hole until it clicks
into place. (If you need to
remove a wire, use a pen tip to
press the terminal release and
then pull the wire out.)
Note: Refer to the wiring picture
you took in Step 1.2.
Tip: To make it easier to slide the
wire into place, use a pen tip to
hold down the terminal release.
Note: The wiring for your
application might be different
than the wiring shown below.
Labels don’t match or have
heat pump system?
See User Guide.
Labels don’t match or have
heat pump system?
See User Guide.
1.7 Attach thermostat to wallplate Align the thermostat with
wallplate and snap into
place.
Before you beginThermostatWallplate
LEVEL
HERE
M34498A
1.8 Switch heating/cooling system ON Important! 1.8a Verify that the C wire is
connected at the thermostat
and at the heating/cooling
system.
1.8b Make sure the heating/
cooling system door is
firmly secured.
1.8c Switch power back ON for
your heating/cooling system
at the breaker box or its
power switch.
Turn over
or
M31535
1.6c In the image on the right, check
the box next to each connection.
You will use this checklist in
Step 1.9.
1.6d Verify wire is firmly secured by
gently pulling on wire.
1.6e Repeat steps a–d for all other
wires.
1.6f Push any excess wire back into
the wall opening after all wires
are installed.
Note: The L terminal on the lower right is used only for Heat Pump systems.Note: If the old thermostat for Heat Pump System has separate wires on Aux and E, use a wire nut to attach both wires to a separate wire. Slide this third wire into the W2-Aux/E terminal.Terminal release
Circuit
breaker
box
Heating/
cooling system
power switch
or
M31535
View the installation video
at wifithermostat.com/
support
You will also need:
Small screw driver
• Pen
Your home WiFi
network password
You will need your
camera to take a
picture of your old wire
connections.
Note: You will need a
picture of your wire
connections to wire
the new thermostat.
Remove jumper loop ONLY if you have both R and Rc wires.
Important!
Check the box for each wire
you connect. You will need
this information in Step 1.9.
C
K
Rc
R
W-O/B
Y
G
W2-
Aux/E
Y2
L
EXAMPLE WIRING
Yours may look different
Resideo Inc., 1985 Douglas Drive North,
Golden Valley, MN 55422
33-00268—05 M.S. Rev. 04-22 | Printed in United States
© 2022 Resideo Technologies, Inc. All rights reserved. The Honeywell Home trademark is used under license from Honeywell International, Inc.
This product is manufactured by Resideo Technologies, Inc. and its affiliates.
www.resideo.com
Electrical Ratings
Terminal Voltage (50/60Hz) Max. Current Rating
W-O/B 2030 Vac 1.0 A
W2 (Aux/E) 2030 Vac 1.0 A
Y Cooling 2030 Vac 1.0 A
Y2 Cooling 2030 Vac 1.0 A
G Fan 2030 Vac 0.5 A
33-00268-05
M38031A
HOME FAN
MODE
SETTINGS
SET TO
INDOOR
54% Humidity
FOLLOWING SCHEDULE
OUTDOOR
55% Humidity
Cool On
6:30 pm
74
°
72
°
72
°

View the manual for the Honeywell RTH9585WF1004 here, for free. This manual comes under the category thermostat and has been rated by 8 people with an average of a 9.3. This manual is available in the following languages: English. Do you have a question about the Honeywell RTH9585WF1004 or do you need help? Ask your question here

Need help?

Do you have a question about the Honeywell and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 211
G
GEORGE GILLHAMDecember 3, 2020

Why does my t-stat not read the inside temp anymore? My heater runs constant now at 70* setpoint. When i shut it down and unplug 30 secs, it reads a higher temp & stays off until it reaches setpoint, and the cycle begins again until I unplug t-stat

1 comment
E
Emma of manua.lsDecember 21, 2023

The temperature reading issue on your Honeywell RTH9585WF1004 thermostat may be caused by a few factors. Here are some troubleshooting steps you can try: 1. Check the power: Make sure the circuit breaker is not tripped and the power switch at the heating and cooling system is turned on. Also, ensure that the furnace door is securely closed. 2. Verify the C wire connection: The C wire provides power to the thermostat. Ensure that the C wire is properly connected. 3. System setup settings: Check the "Your thermostat controls" or "Your system type" setting on the System Setup screen to ensure it matches your heating and cooling equipment. 4. Fan control setting: Verify that the "Your fan control" setting on the System Setup screen is set correctly for your heating equipment. 5. Compressor protection feature: If the thermostat displays "Wait," wait for 5 minutes to allow the system to restart safely without damaging the compressor. 6. Changeover valve configuration: If your heat pump is blowing cool air in heat mode or warm air in cool mode, check the "Type of changeover valve" setting on the System Setup screen to ensure it is properly configured for your system. 7. Check temperature settings: Make sure the temperature setting is higher than the current inside temperature when setting the system to Heat, and lower than the inside temperature when setting it to Cool. If the issue persists after trying these steps, please contact customer support for further assistance.

This answer is automatically generated
A
Al DelaparteFebruary 19, 2021

I am replacing Carrier Thermostat with RTH9585. Old unit has six wires--WOGRCY. What are the proper connections for these wires on the new unit?

2 comments
E
Emma of manua.lsOctober 25, 2023

To determine which wires should be connected to the new Honeywell RTH9585WF1004 thermostat for the letters WOGRCY, please follow these steps: 1. Find the terminal block on the thermostat. 2. Identify the corresponding terminals for each letter: - W: This is for the heating wire. - O: This is for the reversing valve wire for heat pumps. - G: This is for the fan wire. - R: This is for the power wire. - C: This is for the common wire. - Y: This is for the cooling wire. 3. Connect the wires from your HVAC system to the corresponding terminals on the thermostat, following the color-coding or labeling of the wires.

This answer is automatically generated
T
Tim RinglerDecember 15, 2021

I am replacing Carrier Thermostat with RTH9585. Old unit has six wires--WOGRCY. What are the proper connections for these wires on the new unit?

L
Lee OrigerApril 4, 2021

Is there a remote sensor I can connect to my thermostat? I have a Honeywell Home RTH9585WF1004 Wi-Fi Smart Color Thermostat. It is connected to the internet but the outdoor temps vary from app to app to thermostat and I would like to know what the ~temp is outside my home.

Is there a remote sensor I can connect to my thermostat? I have a Honeywell Home RTH9585WF1004 Wi-Fi Smart Color Thermostat. ...
zoom-in
View photo
2 comments
E
Emma of manua.lsOctober 26, 2023

Yes, there is a remote sensor that you can connect to your Honeywell Home RTH9585WF1004 Wi-Fi Smart Color Thermostat. By connecting the remote sensor, you can monitor the temperature outside your home.

This answer is automatically generated
R
Russ BasiuraSeptember 2, 2023

Same unit, same question??

G
Gene CiabattariDecember 11, 2022

I have an old White Rodger’s thermostat with only 4 wires and a jumper. Can I connect your RTH9585WE with the existing wires? Photo below.

I have an old White Rodger’s thermostat with only 4 wires and a jumper. Can I connect your RTH9585WE with the existing wires?...
zoom-in
View photo
1 comment
E
Emma of manua.lsDecember 25, 2023

Yes, you can connect the Honeywell RTH9585WF1004 thermostat with the existing wires of your old White Rodger's thermostat that has only 4 wires and a jumper. Here are the steps to follow: 1. Make sure you have a C wire or equivalent. 2. Attach the thermostat to the wallplate. 3. If your old thermostat had both an R and Rc wire, unplug the jumper loop. 4. If your old thermostat had both an R and RH wire, connect the R wire to the Rc terminal, the RH wire to the R terminal, and unplug the jumper loop. 5. If your old thermostat had both V and VR wires, you can refer to the Honeywell website for help. 6. If your old thermostat had separate O and B wires and is controlling a single zone heat pump system, attach the B wire to the C terminal. If there is more than one thermostat controlling the system, you may need to contact Resideo zoning for wiring assistance. 7. If your old thermostat had separate Y1, W1, and W2 wires, you can refer to the Honeywell website for help. 8. If the old thermostat has separate wires on Aux and E, use a wire nut to attach both wires to a separate wire. Slide this third wire into the W2-Aux/E terminal.

This answer is automatically generated
W
Wendy DickensMay 9, 2023

My panel is not displaying at times and when it does the temperature that is set is different from the actual temperature display on screen. Has this unit gone bad. It started doing this today. How do I fix this.

My panel is not displaying at times and when it does the temperature that is set is different from the actual temperature dis...
zoom-in
View photo
1 comment
E
Emma of manua.lsDecember 18, 2023

The Honeywell RTH9585WF1004 thermostat has a manual available in English. However, I couldn't find specific information about the panel not displaying at times and the temperature being different from the actual temperature. To solve this problem, you can try these steps: 1. Check the power supply: Make sure the thermostat is getting power. Check if the display is lit up and if there are any error messages indicating a power issue. 2. Restart the thermostat: Try restarting the thermostat by removing it from the wall plate and disconnecting the power for a few minutes. Then, reconnect the thermostat and see if the issue persists. 3. Check the wiring: Ensure that the thermostat is properly wired and connected to the HVAC system. Make sure all wires are securely connected and not damaged. 4. Reset the thermostat: If the issue continues, you can try resetting the thermostat to its factory settings. 5. Contact customer support: If none of the above steps resolve the issue, it is recommended to contact Honeywell customer support for further assistance. Please note that these steps are general troubleshooting suggestions and may vary depending on the specific model of the thermostat.

This answer is automatically generated
M
Michael March 5, 2022

Is there a battery? If so, where is it located? I've had this thermostat for a couple of years and it just started crashing and losing connection. It's currently on and set to 70, but the temperature is 65. It won't respond. I've checked breakers, furnace, everything.

This message has been automatically translated
T
Terry sloanApril 27, 2024

I have a rth9585wf1004 thermostat doesn't have auto changeover listed in mode how do I get it in auto changeover

I have a rth9585wf1004 thermostat doesn't have auto changeover listed in mode how do I get it in auto changeover
zoom-in
View photo
W
William SandersJanuary 6, 2021

I own a honeywell home rth9585wf1004 which was left by the previous owner of the house. Im trying to connect to the total connect comfort app but I can't set it up because the previous owners never delete there account. Any suggestions on how to resolve this problem????

The Honeywell RTH9585WF1004 thermostat is a home heating and cooling device designed to provide efficient climate control. This thermostat features a sleek and modern design that can seamlessly blend with any interior decor. Its Wi-Fi capability allows users to control their home's temperature remotely using their smartphone, tablet, or computer. The Honeywell RTH9585WF1004 thermostat is specifically designed to be compatible with the majority of heating and cooling systems, including heat pumps, gas furnaces, and electric heating systems. It offers a user-friendly interface with a customizable color touchscreen display, making it easy to navigate and adjust settings. With its advanced programming capabilities, this thermostat can create a personalized schedule to optimize energy usage and save on utility bills. It also has a Smart Response feature that learns the preferred temperature settings and adapts accordingly. The Honeywell RTH9585WF1004 thermostat has intelligent alerts that notify users about various system issues, such as filter changes or maintenance requirements. It is equipped with geofencing technology, which allows the thermostat to automatically adjust the temperature based on the occupants' location. This thermostat also has voice control compatibility, allowing users to adjust temperature settings using popular voice assistants, such as Amazon Alexa or Google Assistant. Overall, the Honeywell RTH9585WF1004 thermostat provides reliable and convenient climate control for homes, with its user-friendly interface, energy-saving features, and compatibility with a wide range of heating and cooling systems.

General
BrandHoneywell
ModelRTH9585WF1004 | RTH9585WF1004
Productthermostats
EAN0085267911313
LanguageEnglish
FiletypeUser manual (PDF), Quickstart Guide (PDF), Installation Guide (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Honeywell RTH9585WF1004 below.

Where is the best location to place the thermostat?

The best place for the thermostat is the room where you spend the most time, in many cases the living room or kitchen. Place the thermostat about one and a half metres above the floor, not in the sun and not on an outside wall.

What is the dead band of a thermostat?

If your thermostat has a dead band, your installation is, as it were, 'at rest'. The thermostat only switches on when, for example, the difference deviates more than 2˚C from the set room temperature.

What is the ideal room temperature?

Most people find that the ideal room temperature is between 19 and 22 degrees Celsius.

How do I connect my Honeywell RTH9585WF1004 thermostat to my Wi-Fi network?

Simply go to the thermostat settings menu, and select the "Wi-Fi Setup" option. Follow the on-screen prompts to connect the thermostat to your Wi-Fi network.

How do I adjust the temperature setpoints on my thermostat?

Press the "Up" or "Down" arrow buttons on the thermostat's display to adjust the temperature setpoint to your desired level. The changes will be saved automatically.

What should I do if my thermostat is not responding to my commands?

Firstly, ensure that the thermostat is powered on. If it is, try resetting it by pressing the "Menu" button, then selecting "Preferences," and finally choosing "Restore Factory Defaults." If the issue persists, you might need to check the wiring connections or contact customer support for further assistance.

How can I program a schedule on my Honeywell RTH9585WF1004 thermostat?

Press the "Menu" button, select "Program," and then choose "Schedule." From there, you can set different temperature settings for various times of the day. Make sure to save your changes once you've finished programming the schedule.

Can I control my thermostat remotely using my smartphone?

Absolutely! Download and install the Honeywell Home app on your smartphone, create an account, and then follow the app's instructions to pair it with your thermostat. Once paired, you can control and adjust your thermostat from anywhere as long as you have an internet connection.

Is the manual of the Honeywell RTH9585WF1004 available in English?

Yes, the manual of the Honeywell RTH9585WF1004 is available in English .

Is your question not listed? Ask your question here

No results