Honeywell RTH8580WF1007/W1 manual

Honeywell RTH8580WF1007/W1
9.7 · 1
PDF manual
 · 2 pages
English
manualHoneywell RTH8580WF1007/W1
Install your thermostat.
Connect your home Wi-Fi network.
Register online for remote access.
Before you begin
1
2
3
This thermostat works with common 24 volt
systems such as forced air, hydronic, heat pump,
oil, gas, and electric.
It will not work with millivolt systems, such as a
gas fireplace, or with 120/240 volt systems such
as baseboard electric heat.
Apple, iPhone, iPad, iPod touch and iTunes are
trademarks of Apple Inc. All other trademarks
are the property of their respective owners.
C
C
MCR31537
Blank
sticky
tag
Terminal
designation
1.3 Label wires Do not label by wire color.
Use the supplied sticky tags to label
each wire as you disconnect it. Label
wires according to old thermostat
terminal designations, not by wire
color.
Note: If no tag matches a terminal
designation, write the appropriate
letter on a blank sticky tag.
1.4 Remove wallplate
Remove the old wallplate from
the wall after all wires are
labeled and disconnected.
M31538
Finger holds
Wallplate (back view)
Thermostat
1.5 Separate Wi-Fi thermostat and its wallplate
On your new thermostat, grasp the
finger holds on the top and bottom of
the wallplate with one hand and the
thermostat (front) with the other
hand. Pull pieces apart.
Quick Start Guide
Wi-Fi Touchscreen Programmable
Thermostat
RTH8500WF Wi-Fi Series
1.1 Switch OFF power to your heating/cooling system
1.1a Important! To protect your
equipment, switch OFF the
power to your heating/cooling
system at the breaker box or
the system switch.
1.1b Confirm power is OFF.
Try to turn on heating/
cooling equipment by
changing temperature
on your old thermostat.
Your power is OFF if your
system does not turn ON.

Install your thermostat

Turn over

Welcome

Getting set up and ready is simple.
1
or
M31535
If you have an older thermostat with a
sealed mercury tube, see warning page
for proper disposal instructions.
1.2 Remove old thermostat faceplate and leave wires connected 1.2a Take a picture of the
wire connections for
later reference.
1.2b If no wire is connected
to a terminal labeled C
or no C terminal exists
on the old thermostat,
view the Alternate Wiring videos at
wifithermostat.com/videos
Important! C wire is required and is the
primary power source for your thermostat.
Without a C wire, your thermostat will not
power up.
C
C
MCR33823
Wallplate
1.6 Mount wallplate for Wi-Fi thermostat
Mount your new wallplate using screws
and anchors included with the
thermostat.
If necessary:
Drill 3/16-in holes for drywall
Drill 7/32-in holes for plaster
Note: You may be able to use your
existing wall anchors. Hold the wallplate
up to the existing anchors to check
for alignment.
M31543
Y2
W2
K
RC
R
W
Y
G
C
RC
R
O/B
Y
G
C
HEAT PUMPCONVENTIONAL
L
E/AUX
K
R
Y
C
W
G
MCR31539
Y2
W2
K
RC
R
W
Y
G
C
RC
R
O/B
Y
G
C
R
W
G
C
Y

HEAT PUMP

CONVENTIONAL

L
E/AUX
K

MCR31541A

1.7 Connect wires 1.7a Starting with the C Wire, match the
sticky tag on the wire to the terminal
labels.
Important! C wire is required and is the
primary power source. Without a C wire,
your thermostat will not power up.
View the Alternate Wiring videos at
wifithermostat.com/videos
1.7b Loosen screw, insert wire on inside
edge of terminal, then tighten screw.
1.7c Verify wire is firmly secured by gently
pulling on wire.
1.7d Repeat steps 1.7a–1.7c for all other wires.
1.7e Push any excess wire back into the wall
opening after all wires are installed.
Note: The wiring for your
application might be different
than the wiring from above.
Labels don’t match or have heat pump system?
See User Guide.
Remove metal jumper only if you
have both R and RC wires
Insert wires here
1.8 Install battery Insert the coin cell battery
(included), observing
the correct polarity.
Note: A correctly inserted battery will
extend about halfway out of the
battery slot on the thermostat,
allowing for easier removal.
This battery maintains time and date
during power outages. It does not
power the thermostat (C wire
required).
1.9 Attach thermostat to wallplate Align the thermostat onto
wallplate and snap into place.
M31542
Thermostat interior
Circuit
breaker
box
Circuit
breaker
box
Heating/
cooling system
power switch
Heating/
cooling system
power switch
Thermostat
Wallplate

M31543

Y2

W2

K

RC

R

W

Y

G

C

RC

R

O/B

Y

G

C

HEAT PUMP

CONVENTIONAL

L

AUX

/E
K
1.10 Switch heating/cooling system ON Important! 1.10a Verify that the C
wire is connected at the
thermostat and at the
heating/cooling system.
1.10b Make sure the heating/
cooling system door is firmly
secured.
1.10c Switch power back ON for
your heating/cooling system
at the breaker box or its
power switch.
or

M31544

69-2717-07

1.11 Set date and time
Touch s or t buttons to change
displayed time and date.
Press and hold a button to
quickly change a setting.
Day
Time
Month
Year, Month, Day(Top)
Year, Month, Day(Top)

Set Time

Year
Sticky
tag
View the installation video
at wifithermostat.com/
support
Gather
Small screw driver
Thermostat ID card
Your home Wi-Fi
network password

Resideo Technologies, Inc.

1985 Douglas Drive North, Golden Valley, MN 55422

1-800-468-1502

69-2717—07 M.S. Rev. 06-21 | Printed in United States

© 2020 Resideo Technologies, Inc. All rights reserved.

This product is manufactured by Resideo Technologies, Inc. and its affiliates.

www.resideo.com

View the manual for the Honeywell RTH8580WF1007/W1 here, for free. This manual comes under the category thermostat and has been rated by 1 people with an average of a 9.7. This manual is available in the following languages: English. Do you have a question about the Honeywell RTH8580WF1007/W1 or do you need help? Ask your question here

Need help?

Do you have a question about the Honeywell and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 1
J
johnMarch 30, 2024

why doesnt my new honeywell thermostat have a w1 slot

The Honeywell RTH8580WF1007/W1 thermostat is a home heating and cooling device that allows for easy and precise temperature control. This thermostat is designed with the latest technology to provide convenience and energy efficiency. One of the key features of the Honeywell thermostat is its Wi-Fi connectivity, which allows users to control the temperature settings remotely using their smartphones or tablets. This means that homeowners can adjust the temperature of their homes from anywhere, which can lead to energy savings and increased comfort. The thermostat also features a customizable touchscreen display, making it easy to navigate and program. Users can easily set up a schedule for different temperature settings throughout the day, and the thermostat will automatically adjust the temperature based on the programmed schedule. The Honeywell thermostat is also equipped with a Smart Response Learning feature, which allows the thermostat to learn the heating and cooling patterns of the home to optimize energy usage. This feature ensures that the home is always at the desired temperature when needed, while saving energy when the home is unoccupied. Furthermore, the thermostat is compatible with most heating and cooling systems, including conventional systems, heat pumps, and multi-stage systems. This makes it a versatile option for homeowners looking to upgrade their existing thermostats. Overall, the Honeywell RTH8580WF1007/W1 thermostat offers a range of features and functions to provide precise temperature control, energy savings, and convenience for homeowners. With its Wi-Fi connectivity and user-friendly interface, it is a reliable and durable option for controlling the heating and cooling of a home.

General
BrandHoneywell
ModelRTH8580WF1007/W1
Productthermostats
LanguageEnglish
FiletypeQuickstart Guide (PDF), Installation Guide (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Honeywell RTH8580WF1007/W1 below.

Where is the best location to place the thermostat?

The best place for the thermostat is the room where you spend the most time, in many cases the living room or kitchen. Place the thermostat about one and a half metres above the floor, not in the sun and not on an outside wall.

What is the dead band of a thermostat?

If your thermostat has a dead band, your installation is, as it were, 'at rest'. The thermostat only switches on when, for example, the difference deviates more than 2˚C from the set room temperature.

What is the ideal room temperature?

Most people find that the ideal room temperature is between 19 and 22 degrees Celsius.

How do I switch the heating/cooling system ON using the thermostat?

To switch the heating/cooling system ON using the Honeywell RTH8580WF1007/W1 thermostat, follow these steps: 1. Verify that the C wire is connected at the thermostat and at the heating/cooling system. 2. Ensure the heating/cooling system door is firmly secured. 3. Switch the power back ON for your heating/cooling system at the breaker box or its power switch. By following these steps, you can successfully switch ON the heating/cooling system using your Honeywell RTH8580WF1007/W1 thermostat.

What should I do if the heating/cooling system does not turn on after switching it ON?

To troubleshoot if the heating/cooling system does not turn on after switching it ON for the Honeywell RTH8580WF1007/W1 thermostat, follow these steps: 1. Verify that the C wire is connected at both the thermostat and the heating/cooling system. 2. Ensure that the heating/cooling system door is securely closed. 3. Switch the power back ON for your heating/cooling system at the breaker box or its power switch. After completing these steps, test your thermostat by touching the SYSTEM button to change to heating or cooling mode. If the issue persists, refer to the User Guide or FAQ at wifithermostat.com/support for further assistance.

Is the manual of the Honeywell RTH8580WF1007/W1 available in English?

Yes, the manual of the Honeywell RTH8580WF1007/W1 is available in English .

Is your question not listed? Ask your question here

No results