Honeywell RedLINK THM5320R1000 manual

Honeywell RedLINK THM5320R1000
7.5 · 1
PDF manual
 · 60 pages
English
manualHoneywell RedLINK THM5320R1000

RedLINK™ Wireless System

With Equipment Interface Module
® U.S. Registered Trademark.
Copyright © 2011 Honeywell International Inc.
All rights reserved.

System

Installation

Guide

69-2091EFS-07
Wireless control for up to 3 Heat/2 Cool heat pump systems or up to 2 Heat/2
Cool conventional systems.

Installation guide for:

• Wireless equipment interface module
• FocusPRO
®
wireless thermostats
• Wireless remote control
• Wireless outdoor air sensor
• Return air sensor
DISCONNECT POWER BEFORE BEGINNING INSTALLATION. Can cause
electrical shock or equipment damage.
MERCURY NOTICE: If this product is replacing a control that contains mercury in
a sealed tube, do not place the old control in the trash. Contact your local waste
management authority for instructions regarding recycling and proper disposal.
Must be installed by a trained, experienced technician. Read these
instructions carefully. Failure to follow these instructions can damage the product or
cause a hazardous condition.
Français : voir la page 21 Español: vea la página 41

View the manual for the Honeywell RedLINK THM5320R1000 here, for free. This manual comes under the category not categorized and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Honeywell RedLINK THM5320R1000 or do you need help? Ask your question here

Need help?

Do you have a question about the Honeywell and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Honeywell RedLINK THM5320R1000 is a device that falls into the uncategorized category. While there is limited information available on this specific product, it is designed to work with the Honeywell RedLINK wireless technology. RedLINK is a wireless communication protocol that enables various Honeywell devices to connect and interact with each other. The THM5320R1000 likely serves as a thermostat or remote control that is compatible with the RedLINK system. It may allow users to control their HVAC (heating, ventilation, and air conditioning) systems remotely, offering convenience and flexibility in managing indoor temperatures. However, without specific details, it is difficult to determine the exact features and capabilities of this particular model. As with other Honeywell products, the THM5320R1000 is expected to be manufactured with high-quality materials to ensure reliability and long-lasting performance. Honeywell is known for its commitment to delivering dependable solutions, and it is likely that this device adheres to those standards. Additionally, being part of the RedLINK system, it is intended to work seamlessly with other RedLINK-enabled devices to create a comprehensive home automation system. While the THM5320R1000 may have additional specifications and functionalities, these details are currently unavailable. It is recommended to refer to the product documentation or contact Honeywell directly for specific information regarding this device.

General
BrandHoneywell
ModelRedLINK THM5320R1000
Productnot categorized
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Honeywell RedLINK THM5320R1000 below.

What should I do if the wireless devices are not linking to the wireless network as instructed in the installation guide for the RedLINK THM5320R1000?

To link the wireless devices to the wireless network for the Honeywell RedLINK THM5320R1000, follow these steps: 1. Install batteries in all wireless devices, ensuring they are inserted correctly. 2. Restore AC power and press the CONNECT button at the Equipment Interface Module (EIM). 3. Wait for the green flashing light to start linking the devices to the wireless network. 4. If the light stops flashing before all devices are linked, press the CONNECT button again. 5. If the light does not flash, another EIM or wireless adapter may be in wireless setup mode. Exit wireless setup on the other EIM or adapter. 6. Press NEXT on the thermostat to leave the zone number set to zero. 7. Press CONNECT to establish a link to the wireless network. 8. Verify the wireless connection on the confirmation screen and press DONE to display the home screen.

How can I customize the thermostat settings during the installer setup for the RedLINK THM5320R1000?

To customize the thermostat settings during the installer setup for the Honeywell RedLINK THM5320R1000, follow these steps: 1. Press the CONNECT button on the Equipment Interface Module (EIM) to exit wireless setup. 2. Press and hold the FAN and s buttons on the thermostat until the display changes (about 3 seconds). 3. Use the s or t buttons to change the setting as desired at each function screen. 4. Press NEXT to advance to the next function screen. 5. Refer to the tables on pages 9-11 for a description of options for each function. 6. Press DONE to save and exit the customized settings. 7. Remember that the EIM will automatically exit wireless setup after 15 minutes of inactivity. 8. If installing multiple thermostats and EIMs, exit wireless setup before installing additional devices.

What are the risks of not having the Honeywell RedLINK THM5320R1000 system installed by a trained, experienced technician?

Not having the Honeywell RedLINK THM5320R1000 system installed by a trained, experienced technician can lead to potential risks. Failure to follow installation instructions carefully may result in product damage or create hazardous conditions. The system must be installed by a professional to ensure proper setup and functionality. Incorrect installation can cause electrical shock or equipment damage, posing safety hazards. It is crucial to have a trained technician handle the installation to prevent these risks. Always prioritize safety and adhere to the manufacturer's guidelines for installation to avoid any potential issues.

Is the manual of the Honeywell RedLINK THM5320R1000 available in English?

Yes, the manual of the Honeywell RedLINK THM5320R1000 is available in English .

Is your question not listed? Ask your question here

No results