Honeywell MagicStat 32 manual

Honeywell MagicStat 32
7.5 · 2
PDF manual
 · 24 pages
English
manualHoneywell MagicStat 32

MagicStat

®

CT3200 Programmable Thermostat

Installation and Programming Instructions

Welcome
to the world of comfort and energy savings
with your new Honeywell MagicStat
®
Programmable
Thermostat. Your new thermostat will automatically
control the temperature in your home, keeping you
comfortable while saving energy.
If you have any questions about using this thermostat,
visit our home expert Web site at
www.honeywell.com/yourhome
or call Honeywell
Customer Relations at 1-800-468-1502.
®U.S. Registered Trademark
Copyright © 2001 Honeywell • All Rights Reserved
Weekday/Weekend (5-day/2-day)
Programmable Heat and/or Cool
Low Voltage (20 to 30 Vac)
Thermostat and Mounting Plate
Model CT3200

Table of Contents

Installation 2
Programming 11
Operation 17
Change the clock for Daylight/
Standard Time
17
Set the Fan and System switches 17
Replace the batteries 18
Override the program settings 19
Frequently asked questions 21
Limited 1-Year Warranty 23
69- 0653- 6

View the manual for the Honeywell MagicStat 32 here, for free. This manual comes under the category thermostat and has been rated by 2 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Honeywell MagicStat 32 or do you need help? Ask your question here

Need help?

Do you have a question about the Honeywell and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 7
A
Amber MarkhamAugust 8, 2023

We can’t get the cover off our thermostat and need to know if it has a c wire or if we need to get an adapter when we buy a new thermostat

We can’t get the cover off our thermostat and need to know if it has a c wire or if we need to get an adapter when we buy a n...
zoom-in
View photo
1 comment
E
Emma of manua.lsDecember 19, 2023

To remove the cover of the Honeywell MagicStat 32 thermostat, follow these steps: 1. Turn off power to the heating/cooling system. 2. Remove the cover of your old thermostat. 3. Unscrew and remove the old thermostat's mounting plate from the wall, but do not disconnect the wires. 4. Inspect the old thermostat wiring. If the wiring meets any of the following conditions, refer to the special wiring instructions: - The old thermostat is a clock thermostat with wires attached to the C or C1 terminals. - The old thermostat has 6 or more wires, excluding wires attached to C or C1 terminals. - The old thermostat has 3 wires. - There are 5 wires connected to the old thermostat. - There are extra wires that are not connected to the old thermostat. 5. Using the enclosed labels, mark the wires with the letter of the terminal that it is attached to on the old thermostat. Do not label the wires by color. If the labels do not match the letters on the old thermostat terminals, refer to the wiring cross reference table. 6. Disconnect the wires from the old thermostat and wrap the wires around a pencil to keep them from falling back into the wall.

This answer is automatically generated
J
jerry fictumNovember 20, 2023

I set my program ..I press run program but the system on arrow doesn’t show up..why? I had it set to 72..I reprogrammed for 71.

I set my program ..I press run program but the system on arrow doesn’t show up..why? I had it set to 72..I reprogrammed  for ...
zoom-in
View photo
1 comment
E
Emma of manua.lsDecember 19, 2023

The system on arrow may not appear when you set your program and press run program on the Honeywell MagicStat 32 thermostat for a few possible reasons: 1. Make sure the System switch is set to either HEAT or COOL before making any changes to the schedule. The arrow indicating the temporary change will only be displayed if the System switch is set correctly. 2. If you reprogrammed the thermostat for a lower temperature, such as 71, and the arrow is not appearing, it could be because the temporary change to the temperature lasts for the current program period only. The heating/cooling schedule that you programmed will resume when the next scheduled program period is reached. To cancel the temporary change before the next scheduled program period, press the cancel button. 3. If the display is not turning on at all, make sure the batteries are fresh and installed correctly. You can also try removing the batteries and inserting them backwards for five to ten seconds to reset the thermostat. Replace the batteries correctly and the display should turn on. 4. If the temperature display is not going lower than 45°F (7°C) or higher than 88°F (31°C) during programming, it means you have reached the temperature limit. The setting range for the thermostat is 45°F–88°F (7°C–31°C). 5. If the display shows flashing or steady "bAt Lo," it means the batteries are low and need to be replaced. Set the System switch to OFF and insert the batteries backwards for five to ten seconds. Then replace the batteries correctly and the display should turn on. 6. If the temperature change occurs at the wrong times, check the program times for the period in question. Make sure the AM and PM indications are correct and that the current day and time are accurate. Reprogram if necessary. 7. If the heating is not turning on, check that the System switch is set to HEAT. Also, check the system fuse or circuit breaker and replace or reset if necessary. Ensure that the wiring is correct and the connections are good. If the display is blank or displays "bAt Lo," install fresh batteries. Allow time for the furnace to heat up and the fan to come on before checking for heat at the register. If the temperature setting is higher than the current room temperature and the SYSTEM ON arrow is displayed, the thermostat is operating correctly. Contact a heating contractor for assistance if needed.

This answer is automatically generated
C
claire wrightFebruary 3, 2023

can i buy a replacement door - the part that flips up? the little prong on the side broke off so it doesn't stay on anymore...

W
WILLIAM MCDONALDOctober 10, 2019

the read out of the room tempiture is too dim, is there an brightness adjustment?

S
Sharon StoneFebruary 24, 2022

How do you cancel the programs?

S
ScottJanuary 17, 2024

Change from C to F

J
Jerry March 18, 2024

change from celsius to farenheit

The Honeywell MagicStat 32 is a thermostat that is designed to provide efficient temperature control for residential and commercial settings. With its sleek and compact design, it can easily blend in with any decor. The MagicStat 32 boasts precise temperature regulation, allowing users to set their preferred temperature with accuracy. It features a clear and easy-to-read digital display, making it simple to navigate and adjust settings. With its programmable capabilities, users can schedule temperature changes based on their daily routines, improving energy efficiency and reducing utility bills. This thermostat is compatible with a wide range of heating and cooling systems, including gas, oil, electric, and heat pump systems. It also offers a vacation mode, which allows users to save energy while they are away. Installation of the MagicStat 32 is straightforward, and it can be mounted on the wall or placed on a tabletop. It requires a simple wiring connection to the heating and cooling system, ensuring a hassle-free setup process. With its reliable performance and durable construction, the MagicStat 32 is built to last. It is designed to withstand daily use and offers long-term dependability. Overall, the Honeywell MagicStat 32 is a reliable and efficient thermostat that provides precise temperature control and energy savings. With its user-friendly features and durable design, it is a popular choice for both residential and commercial applications.

General
BrandHoneywell
ModelMagicStat 32
Productthermostats
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Honeywell MagicStat 32 below.

Where is the best location to place the thermostat?

The best place for the thermostat is the room where you spend the most time, in many cases the living room or kitchen. Place the thermostat about one and a half metres above the floor, not in the sun and not on an outside wall.

What is the dead band of a thermostat?

If your thermostat has a dead band, your installation is, as it were, 'at rest'. The thermostat only switches on when, for example, the difference deviates more than 2˚C from the set room temperature.

What is the ideal room temperature?

Most people find that the ideal room temperature is between 19 and 22 degrees Celsius.

How do I program the thermostat to automatically adjust the temperature at different times of the day?

Start by pressing the "Program" button on the thermostat, then use the arrow keys to select the desired time period. Adjust the temperature using the arrow keys and press "Set" to save the setting.

Why is my Honeywell MagicStat 32 thermostat not turning on the heating/cooling system?

Firstly, check if the thermostat is set to the correct mode (Heat, Cool, or Auto). Ensure the desired temperature is set higher or lower than the current room temperature, depending on your requirements. Also, make sure the system switch is set to On or Auto. If the issue persists, check the circuit breaker to ensure power supply and verify the thermostat's wiring connections.

How can I override the programmed schedule and manually adjust the temperature?

Press the "Hold" button on the thermostat to temporarily override the programmed schedule and switch to manual control. Adjust the temperature using the arrow keys as needed. To cancel the override and resume the programmed schedule, press the "Hold" button again.

How can I change the display from Fahrenheit to Celsius or vice versa?

Press and hold both the "Up" and "Down" arrow keys simultaneously for a few seconds. The display will switch between Fahrenheit and Celsius units.

How do I adjust the temperature calibration if the thermostat temperature reading seems inaccurate?

Start by pressing the "Up" and "Down" arrow keys at the same time for a few seconds to enter the calibration menu. Then, use the arrow keys to adjust the calibration offset value up or down until the desired accuracy is achieved.

Is the manual of the Honeywell MagicStat 32 available in English?

Yes, the manual of the Honeywell MagicStat 32 is available in English .

Is your question not listed? Ask your question here

No results