Honeywell Chronotherm IV T8602D manual

Honeywell Chronotherm IV T8602D
8.1 · 2
PDF manual
 · 12 pages
English
manualHoneywell Chronotherm IV T8602D
® U.S. Registered Trademark
Copyright © 2003 Honeywell International Inc. • • All Rights Reserved
INSTALLATION INSTRUCTIONS
69-1510-
4

T8602D Chronotherm® IV

Programmable Thermostats

APPLICATION

The T8602 Chronotherm® IV Programmable Thermostat
provides electronic control of 24 Vac single-stage heating
and cooling systems or 750 mV heating and 750 mV
cooling. Refer to Table 1 for a general description of the
thermostat. All T8602 Thermostats are powered by
batteries.

MERCURY NOTICE

If this control is replacing a control that contains
mercury in a sealed tube, do not place your old
control in the trash. Dispose of properly.
Contact your local waste management authority
for instructions regarding recycling and the
proper disposal of the old control.

INSTALLATION

When Installing this Product...
1. Read these instructions carefully. Failure to follow
the instructions can damage the product or cause
a hazardous condition.
2. Check the ratings given in the instructions and on
the product to make sure the product is suitable for
your application.
3. Installer must be a trained, experienced service
technician.
4. After completing installation, use these instructions
to check out the product operation.
Location
Install the thermostat about 1.5m (5 ft) above the floor in
an area with good air circulation at average temperature.
See Fig. 1.
Do not install the thermostat where it can be affected by:
drafts, or dead spots behind doors and in corners.
hot or cold air from ducts.
radiant heat from sun or appliances.
concealed pipes and chimneys.
unheated (uncooled) areas such as an outside wall
behind the thermostat.
Wallplate Installation
The thermostat can be mounted horizontally on the wall
or on a 50.8 mm x 101.6 mm (2 in. x 4 in.) wiring box.
Position wallplate horizontally on the wall or on a
50.8 mm x 101.6 mm (2 in. x 4 in.) wiring box.
1. Position and level the wallplate (for appearance
only). The thermostat will function properly even
when not level.
2. Use a pencil to mark the mounting holes. See Fig.
2.
3. Remove the wallplate from the wall and drill two
4.76 mm (3/16 in.) holes in the wall (if drywall) as
marked. For firmer material such as plaster, drill
two 5.56 mm (7/32 in.) holes. Gently tap anchors
(provided) into the drilled holes until flush with the
wall.
4. Position the wallplate over the holes, pulling wires
through the wiring opening.
5. Loosely insert the mounting screws into the holes.
6. Tighten mounting screws.
Table 1. Description of T8602 Thermostats.
T8602 System Changeover
System
Selection
Fan
Selection Comments
D Heat-Cool Manual or
Automatic
Selectable
Heat-Off-Cool or
Heat-Off-Cool-Auto
On-Auto System and fan selections are done
by keyboard.

View the manual for the Honeywell Chronotherm IV T8602D here, for free. This manual comes under the category thermostat and has been rated by 2 people with an average of a 8.1. This manual is available in the following languages: English. Do you have a question about the Honeywell Chronotherm IV T8602D or do you need help? Ask your question here

Need help?

Do you have a question about the Honeywell and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 12
O
OscarFebruary 21, 2023

Why appears filter blinking in the screen

Why appears filter blinking in the screen
zoom-in
View photo
R
Randal MorrisOctober 2, 2022

how do I reset the filter alert

1 comment
C
Cynthia FrenchOctober 5, 2022

How do I reset the filter alert?

N
Nadine MartinDecember 3, 2022

How can i see the times that are set?

C
CkJanuary 16, 2023

How do you use the copy program function?

V
Vaughn CassinghamMarch 6, 2023

How do I turn off “Filter” message on display?

P
Paul OppenheimJuly 3, 2023

We have a Honeywell Chronotherm IV Plus thermostat. It was installed in 2003. When the air conditioning is turned on, the temperature reading will increase to about 8 -10 degrees over the set temperature (i.e. temperature set at 75 degrees, but thermostat temperature will climb to 85 degrees). The AC system will continue running until we either turn it off manually, or reset the programmed temperatuture to 85 degrees. (By the way, there don't appear to be any batteries for this model) How do we fix this?

2 comments
M
Mary AnnSeptember 4, 2023

I have the exact same problem. Is there an answer?

D
Don GroeneveldMarch 17, 2024

@Paul Oppenheim Did they answer you

J
John E AndersonJuly 28, 2023

My filter is flashing and I can't remember sequence to reset to 30 days

J
John JacobsonNovember 16, 2023

How to set another time for the wake setting

P
Patrick April 15, 2023

How to replace cover plate

CortMay 28, 2023

How to reset filter replacement

The Honeywell Chronotherm IV T8602D is a thermostat designed for residential use. It offers basic functions to regulate temperature within a home, ensuring optimal comfort for its users. The thermostat features a clear and easy-to-read digital display, allowing for precise temperature adjustments. With a sleek and minimalistic design, the Honeywell Chronotherm IV T8602D seamlessly blends into any home decor. It is designed to be wall-mounted and can be easily installed by a professional technician. The thermostat offers a variety of programming options, allowing users to schedule temperature changes throughout the day. This ensures energy efficiency by automatically adjusting the temperature based on the user's preferences and schedule. While specific technical specifications are not provided, the Honeywell Chronotherm IV T8602D likely includes features such as temperature control range, programmable set points, and compatibility with various heating and cooling systems. It may also have advanced features such as vacation mode, fan control, and filter change reminders. Overall, the Honeywell Chronotherm IV T8602D is a reliable and user-friendly thermostat that provides effective temperature control for residential use. Its design, functionality, and programmable features make it a practical choice for homeowners looking to optimize energy efficiency and comfort in their homes.

General
BrandHoneywell
ModelChronotherm IV T8602D
Productthermostats
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Honeywell Chronotherm IV T8602D below.

Where is the best location to place the thermostat?

The best place for the thermostat is the room where you spend the most time, in many cases the living room or kitchen. Place the thermostat about one and a half metres above the floor, not in the sun and not on an outside wall.

What is the dead band of a thermostat?

If your thermostat has a dead band, your installation is, as it were, 'at rest'. The thermostat only switches on when, for example, the difference deviates more than 2˚C from the set room temperature.

What is the ideal room temperature?

Most people find that the ideal room temperature is between 19 and 22 degrees Celsius.

How do I set the thermostat to a specific temperature?

To set the thermostat to a specific temperature, press the "Set" button, followed by the up or down arrow buttons to adjust the desired temperature.

What should I do if the display on the thermostat is not turning on?

If the display is not turning on, check the power supply by ensuring the thermostat is properly connected to the electrical source. If the issue persists, verify the circuit breaker for the thermostat is not tripped.

How can I program the thermostat to automatically adjust temperature at specific times?

To program automatic temperature adjustments, press the "Program" button, followed by selecting the desired day(s) using the arrow buttons. Then, set the desired heating or cooling temperature for each time period using the up or down arrow buttons.

How do I override the programmed temperature and manually adjust it temporarily?

To temporarily override the programmed temperature, press the "Hold" button. Then, use the up or down arrow buttons to set the desired temperature. The manual override will remain in effect until the next scheduled program change, or until the "Hold" button is pressed again to cancel it.

What should I do if the thermostat is not turning on the heating or cooling system?

If the thermostat is not turning on the heating or cooling system, check if the thermostat is set to the correct mode (heat, cool, or auto). Additionally, ensure the heating or cooling system itself is functioning properly and that the thermostat is set to a temperature requiring activation. If the issue persists, it is recommended to contact a professional technician for further assistance.

Is the manual of the Honeywell Chronotherm IV T8602D available in English?

Yes, the manual of the Honeywell Chronotherm IV T8602D is available in English .

Is your question not listed? Ask your question here

No results