enable the function. Position, size, and the defog
gradation are configurable.
3.3.4 Backlight
Backlight Compensation (BLC):
Set the gain of BLC as High, Middle, or Low.-GAIN:
Press the up/down/left/right button to-AREA:
define the BLC position and size. Select RET or
AGAIN to go back the BLC menu or re-define the
BLC area.
Restore the BLC settings to the default.-Default:
HSBLC:Select an HSBLC area. Set the DISPLAY
status as ON. Press the up/down/left/right button
to define the area position and size. Set the HSBLC
LEVEL from 0 to 100. Select ALL DAY or Night for the
HSBLC mode. Set the BLACK MASK status as ON or
OFF.
HSBLC
1. SELECTAREA 1
2. DISPLAYON8
3. LEVEL---|------ 40
4. MODEALL DAY
5. BLACK MASKON
6. DEFAULT8
7. RETURNRET
Figure 3-3 HSBLC
3.3.5 White Balance (WB)
INDOOR, OUTDOOR, MANUAL, ATW (Auto-tracking
White Balance), AWC→SET are selectable.
3.3.6 Day & Night
Color, B/W, and EXT are selectable for DAY and
NIGHT switches.
3.3.7 NR
: You can set 2D NR status as ON or OFF.2D NR
: Set the Smart NR status as ON and adjust3D NR
the 3D smart NR sensitivity ranges from 0 to 100.
Set the 3D NR LEVEL ranges from 0 to 100. Set the
2D&3DNR
1. 2DNROFF
2. 3DNRON
8
3. RETURNRET
3DNR
1. SMART NRON
8
2. LEVEL------|--8 0
3. START. AGC-|--------10
4. END. AGC-|--------10
5. RETURNRET
Figure 3-5 NR
Figure 3-6 3D NR
3.3.8 SPECIAL
Edit the camera title on this section.Camera Title:
D-effect:
Set the freeze function as ON or OFF.-FREEZE:
OFF, MIRROR, V-FLIP, and ROTATE are-MIRROR:
selectable for mirror.
Define the zoom area by configuring-D-ZOOM:
the position from PAN & TILT.
The D-Zoom area, sensitivity-SMART D-ZOOM:
and time are configurable.
Set the NEG IMAGE as ON or OFF.-NEG.IMAGE:
SPECIAL
1. CAM TITLEON
8
2. D-DFFECT8
3. MOTIONOFF
4. PRIVACYOFF
5. LANGUAGEENG
8
6. DEFECT8
7. VERSION130722
8. RETURNRET
Figure 3-7 Special
MOTION
1. SELECTAREA 1
2. DISPLAYON8
3. SENSITIVITY----|---- 30
4. MOTIONVIEWON
5. DEFAULT8
6. RETURNRET
Figure 3-8 Motion Detection
Motion: Select a MOTION area. Set the DISPLAY
status as ON or OFF. Press the up/down/left/right
button to define the position and size of the area.
Set the SENSITIVITY from 0 to 60. Set the MOTION
VIEW status as ON or OFF.
Privacy: Select a PRIVACY area. Set the DISPLAY
status as INV, MOSAIC, COLOR or OFF. Press the
up/down/left/right button to define the position
and size of the area.
Defect: LIVE DPC, STATIC DPC and Black DPC are
adjustable in this section.
: You can check the software version of theVersion
device.
PRIVACY
1. SELECTAREA1
2. DISPLAYMOSAIC
8
3. COLOR10
4. TRANS.1
5. DEFAULT
8
6. RETURNRET
ADJUST
1. SHARPNESS
--------|15
2. MONITORLCD8
3. LSCOFF
4. VIDEO. OUTPAL
5. RETURNRET
3.3.9 ADJUST
: Adjust the sharpness from 0 to 15.Sharpness
: Monitor CRT, and Monitor LCD areMonitor
selectable.
: Set the LSC status as ON or OFF.LSC
3.3.10 RESET
Reset all the settings to the default.
3.3.11 EXIT
Press OK to exit the menu.
START. AGC level as the threshold to enable AGC,
and set the END. AGC level as the threshold to
disable AGC.
Figure 3-9 Privacy Mask
Figure 3-10 Adjust
3.Route the cables to the cable hole and connect
the corresponding power cable and video cable.
4.Fix the camera to the ceiling with the supplied
screws.
Figure 2-2 Fix the Camera to the Ceiling
5.Adjust the surveillance angle.
1).Loosen No.3 adjusting screw to adjust the
panning position0~ 360.(°°)
.2).Tighten No.3 adjusting screw
3).Loosen the No.2 adjusting screw to adjust the
tilting position0~ 90(°°).
4).Tighten No.2 adjusting screw.
5).Loosen No.1 adjusting screw to adjust the
azimuth angle of the image0~ 360(°°).
.6).Tighten No.1 adjusting screw
Figure 2-3 3-axis Adjustment
Steps:
1.Drill the screw holes and the cable hole in the
ceiling according to the supplied drill template.
2.Hammer the supplied plastic expansion bolt into
the screw holes.
2.2 Wall Mounting for Type /IIIII
Camera
Figure 2-4 Drill Template
2
1
Ceiling Mounting
2
2
2
1
1
1
No.2 Screw Hole
for Mounting
Base
No.1 Screw Hole
for Bracket
Figure 2-5 Fix the Camera to the Wall
Figure 2-6 3-axis Adjustment
90°
360°
360°
3
2
1
5. Adjust the surveillance angle.
1). Loosen No.3 adjusting screw to adjust the pan
position (0~ 360).°°
2).Tighten No.3 adjusting screw.
3). Loosen No.2 adjusting screw to adjust the
tilting position(0~ 90).°°
4).Tighten No.2 adjusting screw.
5). Loosen No.1 adjusting screw to adjust the
rotation position0~ 360.(°°)
6).Tighten No.1 adjusting screw.
3.Route the cables to the cable hole and connect
the corresponding power cable and video cable.
4.Fix the camera to the ceiling with the supplied
screws.
Adjusting Screw
l A coaxial camera controller (purchase separately)
is required to select the menu and adjust the
camera parameters.
Cameras with a 720p resolution of these three
l
types do not support menu operation.
Manual
View the manual for the Hikvision Turbo HD Bullet Camera here, for free. This manual comes under the category security cameras and has been rated by 1 people with an average of a 7.9. This manual is available in the following languages: English. Do you have a question about the Hikvision Turbo HD Bullet Camera or do you need help? Ask your question here
Need help?
Do you have a question about the Hikvision and is the answer not in the manual?
Receive updates on solutions
Get answers to your question
Question and answer
Number of questions: 0
Hikvision Turbo HD Bullet Camera specifications
Below you will find the product specifications and the manual specifications of the Hikvision Turbo HD Bullet Camera.
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Hikvision Turbo HD Bullet Camera below.
What is the weight of the Hikvision Turbo HD Bullet Camera?
The Hikvision Turbo HD Bullet Camera has a weight of 700 g.
What is a megapixel?
The number of megapixels denotes how many pixels there are in the sensor. 1 megapixel equals 1 million pixels. The more pixels, the higher the potential image quality.
What does the abbreviation 'MP' stand for?
MP stands for MegaPixels.
What is the height of the Hikvision Turbo HD Bullet Camera?
The Hikvision Turbo HD Bullet Camera has a height of 210.8 mm.
What is the width of the Hikvision Turbo HD Bullet Camera?
The Hikvision Turbo HD Bullet Camera has a width of 94.6 mm.
What is the depth of the Hikvision Turbo HD Bullet Camera?
The Hikvision Turbo HD Bullet Camera has a depth of 83 mm.
Is the manual of the Hikvision Turbo HD Bullet Camera available in English?
Yes, the manual of the Hikvision Turbo HD Bullet Camera is available in English .
Need help?
Do you have a question about the Hikvision and is the answer not in the manual?
Question and answer
Number of questions: 0