DS-KD9613-E6/FE6 Fac e Rec og ni ti on D oo r St ati o n
Diagram References E N G L I S H Appearance Installation Before you begin:
Call from Main/Sub Door Station
Call from Outer Door Station
Accessory (Sales seperately) 1
3
Terminal 2
Light
Camera
Microphone
1 2 3
4
5 6
1. Accessories that you need to pr epare for ins tallation: Junction box and mounting template.
2. Make sure the power supply meet the power requirements of the door station (12 VDC, 2 A).
3. Make sure all the related equipment is power-o during the in stallation.
4. Wire the cables before installation.
The dimension of the junction box is: 406.7 mm(W) × 174.8 mm(H) × 44 mm(D).
The installation hole should be larger than junction box. The suggested dimension of the installation
hole i s 407.5mm(W) × 175.5(H) × 44.5(D) mm.
Noteğ ask our technique supports and sales and purchase DS-KABD9613-G junction box.
Flush Mounting 1. Drill an installation hole on the wall.
Note: The suggested size of hole is 407.5mm(W) × 175.5(H) × 44.5(D) mm.
2. Insert the junction box to the wall. Secure the junction and the wall with 4 supplied screws.
3. Insert the door station to the junction box.
4. Fix the door station with the set screw.
NoteThedoors tati on can be congur ed via iVMS-4 200 Client Soft war e.
Screen
Card Reader Area
NC1/NC2: Door Lock Relay Output (NC)
NO1/NO2: Door Lock Relay Output (NO)
COM1/COM2: Common Interface
DC 12 V: Power Input
AO1+/A O1- : Alarm Relay Output 1
AO2+/A O2- : Alarm Relay Output 2
AI1/AI2/ AI3: Alarm Input
GND: Grounding
485-: RS-485 Communication T erminal
485+: RS-485 Communication T erminal
T A MPWi eg andC ar d Rea der T AMP ER
OK: Card Reader Indicator Output (Valid)
ERR: Card Reader Indicator Output (Invaild)
BZ: Card Reader Buzzer Output
W0: Data Input Interface Wiegand Card Reader
W1: Data Input Interface Wiegand Card Reader
12 V: Power Supply Output
Note: The appearance of the device vary according to dierent model. Refers to the actual device.
Note: Wiring description refers to the User Manual.
Conguration4 Ref er to Video Intercom Face Recognition Door Station User Manual (scan the QR code) for details.
UD 16 88 9B -A
1 2
1
2
3
4
5 6
7
3
3
● All the electronic operation should be strictly compliance with the electrical safety regulations, re prevention regulations and other related regulations in your
local region.
● Please use the power adapter , which is provided by normal company. The power consumption cannot be less than the required value.
● Do not connect several devices to one power adapter as adapter overload may cause over-heat or re hazard.
● Please make sure that the power has been disconnected before you wire, install or dismantle the device.
● When the product is installed on wall or ceiling , the device shall be rmly xed.
● If smoke, odors or noise rise from the device, turn o the power at once and unplug the power cable, and then please contact the service center .
● If the product does not work properly , please contact your dealer or the nearest service center . Never attempt to disassemble the d evice yourself. (We shall
not assume any responsibility for problems caused by unauthorized repair or maintenance.)
● Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equi pment installation on vibrations
surface or places subject to shock (ignorance can cause equipment damage).
● Do not place the device in extremely hot (refer to the specication of the device for the detailed operating temperature), cold, dusty or damp locations, and do
not expose it to high electromagnetic radiation.
● The device cover for indoor use shall be kept from rain and moisture.
● Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause re danger).
● Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and aecting the
endurance of sensor at the same time.
● Please use the provided glove when open up the device cover , avoid direct contact with the device cover , because the acidic sweat of the ngers may erode
the surface coating of the device cover .
● Please use a soft and dry cloth when clean inside and outside surfaces of the device cover , do not use alkaline detergents.
● Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original
wrapper . Tr ansportation without the original wrapper may result in damage on the device and lead to additional costs.
● Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries
according to the instructions provided by the battery manufacturer .
Cautions
Warnings
● T ous les éléments électroniques doivent respecter à la lettre la réglementation locale sur la sécurité des installations électriques, sur la prévention des incendies
et des réglementations connexes en vigueur.
● Utilisez un adaptateur fourni par une entreprise agréée. La consommation électrique ne doit pas être inférieure à la valeur exigée.
● Ne branchez pas plusieurs appareils sur un même adaptateur ; toute surcharge de l'adaptateur pouvant entraîner sa surchaue ou provoquer un incendie.
● Veillez à bien déconnecter la source d’ alimentation avant de câbler , installer ou démonter l’appareil.
● Lors de l'installation au mur ou au plafond, assurez-vous que l'appareil est bien xé.
● Si l'appareil dégage de la fumée ou une odeur suspecte, ou s'il émet des bruits inhabituels, éteignez-le et débranchez le câble d'alimentation, puis contactez le
SAV .
● Si le produit ne fonctionne pas correctement, contactez votre revendeur ou le SAV le plus proche. Vous ne devez en aucun cas essayer de démonter le produit
vous-même. (Nous déclinons toute responsabilité en cas de problèmes découlant d'une intervention ou d'une réparation eectuée sans autorisation.)
● Évitez de faire tomber l’ appareil, de le heurter et de l'exposer à d es rayonnement s électromagnétiques de forte intensité. Évitez d'installer l'équipement sur des
surfaces vibrantes ou à des emplacements subissant des chocs fréquents (au risque de l'endommager).
● N'installez pas l’appareil à un emplacement trop chaud ou trop froid (reportez-vous à la spécication de l’appareil pour connaître la température de
fonctionnement précise), poussiéreux ou humide. Ne l'exposez pas non plus à des rayonnements électromagnétiques élevés.
● Le capot de l’ appareil pour installation intérieure ne doit pas être exposé à la pluie, ni à l'humidité.
● Il est formellement interdit d'exposer l'équipement directement au soleil, à un environnement mal ventilé ou à une source de chaleur telle qu'une chaudière ou
un radiateur (au risque de provoquer un incendie).
● N'orientez pas l’appareil vers le soleil ou des sources de lumière très vive. Dans le cas contraire, un voile ou des traînées risquent de se former (ce qui ne
constitue toutefois pas un dysfonctionnement) et la résistance du capteur peut également être aectée.
● Utilisez le gant fourni pour ouvrir le capot du dôme et évitez tout contact direct avec celui-ci, l'acidité de la sudation des doigts pouvant éroder le revêtement du
capot de l’ appareil.
● Utilisez un chion doux et sec pour nettoy er les surfaces intérieures et extérieures du capot de l’ appareil. N'utilisez pas de détergents alcalins.
● Conservez tous les emballages ; ils pourront vous resservir ultérieurement. En cas de panne, renvoyez l’appareil à l'usine dans son emballage d'origine. Si
l’ appareil est transporté hors de son emballage d'origine, il risque d'être abîmé, entraînant des frais supplémentaires.
● Une mauvaise utilisation de la batterie ou un remplacement erroné peut entraîner un risque d'explosion. Ne la remplacez que par une batterie identique ou de
type équivalent. Mettez les batteries usagées au rebut conformément aux instructions du fabricant.
Précautions
Avertissements :
Activate Device 1. Power on the device to enter the activation page automatically .
2. Create a password and conrm it.
3. Tap OK to activate the door station.
Y ou are required to activate the device rst by setting a strong password for it before you can use the
device.
1
Edit Network Parameters 1.Long tap on the initial page for 3 s and slide to the left/right and log in the backend.
Note: By default, the admin password is activation password.
2. Tap Network Settings.
3. Edit IP address, Subnet Mask, Gateway , S IP IP , Master Station IP and Center IP according to your needs.
4. Tap < on the top left of the page to save the settings.
1.Long tap on the initial page for 3 s and slide to the left/right and log in the backend.
Note: By default, the admin password is activation password.
2. Tap Local Settings.
3. Set project No., buliding No., unit No. and oor No.
4. Set No. for sub door station.
5. Tap < on the top left of the page to save the settings.
Note:
1. The No. of the main door station is 0.
2. The No. of the sub door stations should be set from 1 to 99.
3. The No. of the outer door station should be set from 1 to 99.
4. E very unit should have at least one main door station. Up to 8 sub door stations can be linked to the
same main door station.
1.Long tap on the initial page for 3 s and slide to the left/right and log in the backend.
Note: By default, the admin password is activation password.
2. Tap User Management. Swipe the main card or enter the user ’s password.
3. Add user ’s parameters according to the notice on the page.
- Set Room No.
- Add card, face, ngerprint for the user .
- Sel ect User Type.
4. Tap √ to save the settings.
Note: The page may vary according to dierent device models. Refer s to the actual page for details.
Set the network parameter s of the door sta tion and linked devices.
2
Set Door Station No. 3
User Management T ap Call/Open, enter the room No. and press the call button.
T ap Call/Open, enter community No. + building No. + # + u nit No. + # + room No. and press call button.
4
Call Resident 5
Unlock by Entering Password
Unlock by Swiping Card
The device support unlock the door by swiping card, entering password, scanning QR code, and ngerprint.
Here takes unlock by entering password and unlock by swiping card for example.
Note: You should create the password and add the card to the device rst.
Normal Password
T ap Call/Open, enter # + room No. + password and press the un lock button.
Note: By default, the password is 123456.
Public Password
Note: Create the public password via iVMS-4200 Client Software remotely rst.
T ap Call/Open, enter # + public password and press the unlock button.
Present the card on the card reading area to unlock the door .
Unlock Door 6
Regulatory Information FCC Information Please take attention that changes or modication not expressly approved by
the party responsible for compliance could void the user’s authority to operate
the equipment.
FCC compliance: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection agains t harmful
interf erence in a residential installa tion. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interf erence to radio communications.
However , there is no guarant ee that interfe rence will not occur in a particular
installation. If this equipment does cause harmful interfer ence to radio or
television reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
—Reorient or reloca te the receiving antenna.
—Increase the separation between the equipment and receiver .
—Connect the equipment into an outlet on a circuit di er ent from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interf erence received, including interfere nce th at
may cause undesired operation.
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable
harmonized European standards listed under the RE Directive
2014/53/EU, the EMC Directive 2014/30/EU, the LVD Directive
2014/35/EU, the RoHS Directive 2011/65/EU
2012/19/EU (WEEE directive): Products mark ed with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see: www .recycle-
this.info
2006/66/EC (battery directive): This product contains a batt ery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specic batt ery information.
The battery is marked with this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling,
return the batt er y to your supplier or to a designated collection point.
For more informa tion see:www.recy clethis.info
Product Inf ormation ©2021 Hangzhou Hikvision Digital T echnology Co., Ltd. It includes instructions on how to use the Product. The software embodied in the Product is governed by the user license agreement covering that Product. About this Manual This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision Digital T echnology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This manual cannot be reproduced, changed, translated, or distributed, partially or wholly , by any means, without the prior written permission of Hikvision. T rademarks and other Hikvision marks are the property of Hikvision and are registered trademarks or the subject of applications for the same by Hikvision and/or its aliates. Other trademarks mentioned in this manual are the properties of their respective owners. No right of license is given to use such trademarks without express permission. Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDW ARE, SOFTWARE AND FIRMWARE, IS PROVIDED “ AS IS” , WITH ALL FA UL TS AND ERRORS, AND HIKVISION MAKES
NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMIT A TION, MERCHANT ABILITY , SA TISFA CTORY QUALITY , FITNESS FOR A P ARTICULAR
PURPOSE, AND NON-INFRINGEMENT OF THIRD P ARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLO YEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DA T A OR DOCUMENT A TION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY A T YOUR OWN RISKS. HIKVISION SHALL NOT T AKE ANY RESPONSIBILITIES FOR ABNORMAL OPERA TION, PRIVACY LEAKAGE OR OTHER DAMAGES RESUL TING FROM CYBER A TTACK, HACKER A TT ACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMEL Y TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THA T YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THA T THIS PRODUCT IS USED WITH ILLEGITIMA TE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Data Protection During the use of device, personal data will be collected, stored and processed. T o protect data, the development of Hikvision devices incorporates privacy by design principles. For example, for device with facial recognition features, biometrics data is stored in your device with encryption method; for ngerprint device, only ngerprint template will be saved, which is impossible to reconstruct a ngerprint image. As data controller, you are advised to collect, store, process and transf er data in accordance with the applicable data protection laws and regulations, including without limitation, conducting security controls to safeguard personal data, such as, implementing reasonable administrative and physical security controls, conduct periodic reviews and assessments of the eectiveness of your security controls. 7Card Reading & Fingerprint Recognition Area T AMPER
Need help?
Do you have a question about the Hikvision and is the answer not in the manual?
Question and answer
Number of questions: 0