Hikvision DS-KD-M manual

Hikvision DS-KD-M
7.1 · 1
PDF manual
 · 100 pages
English
manualHikvision DS-KD-M

DS-KD-KK DS-KD-M(E)

Video Intercom Module Door Staon UD21094B-AENGLISHDiagram References
1
Call Buon
2
Card Reading Area
3
4
5
Module-connecng Interface (Output)
6
Debugging Port
Note: The module-connecng interface is used to connect other funcon module, such as nametag module,
keypad module, card reader module, etc. All these modules are known as sub module.
Appearance
1
1
Nametag
Terminal
2
A1
A2
A3
A4
485-: Module-connecng Interface (Input)
B1
B2
B3
B4
Installaon
3
Note: Video intercom module door staon support one-module installaon, two-module installaon, three-
module installaon and more-than-three-module installaon. Here takes three-module installaon as an
example.
Tools that you need to prepare for installaon: Drill(6), cross screw driver (PH1*150
mm), and gradienter.
Make sure all the related equipment is power-off during the installaon.
Make sure you have configured the sub module address before installaon. Valid sub
module address range is 1 to 8. The No. should be unique for sub modules that
connected to the same main unit. The sub module address and corresponding switch
status is shown as the figure.
Before You StartThree-Module Flush Mounng
1. Cave the installaon hole, and pull the cable out.
Note: The suggested dimension of the installaon hole is 321.8(W) × 108(H) × 45.5(D) mm. The suggested
length of the cables le outside is 270 mm.
2. Select a cable entry and remove the plasc sheet. Route the cables through the gang
box hole. Insert the gang box into the installaon hole. Mark the gang box screw holes’
posion with a marker, and take out the gang box.
3. Drill 4 holes according to the marks on the wall, and insert the expansion sleeves into
the screw holes. Fix the gang box with 4 expansion bolts.
4. Fill the gap between the gang box and wall with concrete or Silicone sealant. Remove
the mounng ears with tool aer concrete is dry.
5. Connect cables and insert the modules.
a.Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the main
unit, then insert the main unit into the upper grid.
b.Connect the other end of Cable 2 to the input interface of Sub Module 1. Connect
one end of Sub Module 1 and insert it into the middle grid.
c.Connect the other end of Cable 3 to the input interface of Sub Module 2. Insert it
into the boom grid.
6. Fix the cover and the main unit with 2 socket head cap screws by using a hexagon
wrench.
Surface Mounng with Protecve Shield
1. Paste the installaon scker 1 onto the wall. Make sure the scker is placed
horizontally via measuring with the gradienter. Drill 4 holes according to the screw holes
on the scker.
Note: The suggested size of hole is 6(diameter) × 25(depth) mm. The suggested length of the cables le
outside is 270 mm.
2. Remove the scker and insert the expansion sleeves into the screw holes. Fix the
mounng frame
onto the wall with 4 expansion bolts.
3. Thread the module-connecng line across the thread holes of the frame. Pass the
main unit
connecng line across the thread hole to the top grid and connect the cables.
a.Connect the lines and module-connecng line 1 to the corresponding interfaces of
the main unit,
then place the main unit into the upper grid.
b.Connect the other end of the module-connecng line 1 to the input interface of the
sub modules via module-connecng line 2.
c.Organize the cables with cable e in the package.
4. Insert the modules into the frame aer wiring. The main unit must be placed in the
top grid.
5. Use the hexagon wrench in the package to fix the cover onto the frame.
Gang Box

1 2 3 4 5 6

13

Expansion BoltMounng EarMain UnitSub Module 1Sub Module 2HexagonalScrew
1
2
2
2
1
3
3
3

13

1
2
3
4
5 6
2
Module-connecng Interface (Input)
A1 A4 B4B1
GND
12V OUT
485+
485-
GND
12V IN
485+
485-
RS485 IN RS485 OUT
485+: Module-connecng Interface (Input)
12V IN: Module-connecng Interface (Input)
GND: Module-connecng Interface (Input)
485-: Module-connecng Interface (Output)
485+: Module-connecng Interface (Output)
12V IN: Module-connecng Interface (Output)
GND: Module-connecng Interface (Output)
Nametag Module Card Reader Module
1

2 3 4 5

Module-Connecng Line1Module-Connecng Line2Thread HoleCables Connectedto Main ModuleMain UnitSub ModuleMounng FrameHexagonalScrewCoverHexagon Wrench

View the manual for the Hikvision DS-KD-M here, for free. This manual comes under the category intercom systems and has been rated by 1 people with an average of a 7.1. This manual is available in the following languages: English. Do you have a question about the Hikvision DS-KD-M or do you need help? Ask your question here

Need help?

Do you have a question about the Hikvision and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Hikvision DS-KD-M is a card reader product designed for use with Hikvision brand intercom systems. This product is sold individually and has dimensions of 33.7 millimeters in depth, 100 millimeters in height, and 98.5 millimeters in width. It operates on a DC input voltage of 12 volts and has an International Protection (IP) code of IP65, indicating it is protected against dust and water ingress. The weight of the card reader is 160 grams, while the package weight is 421 grams. It is designed for surface mounting and comes with sustainability certificates including REACH, RoHS, and WEEE. This ensures that the product is compliant with environmental regulations. The Hikvision DS-KD-M is a compact and lightweight card reader that is suitable for use in a variety of settings where secure access control is required. With its durable construction and compatibility with Hikvision intercom systems, this product is a reliable choice for those in need of a card reader solution.

General
BrandHikvision
ModelDS-KD-M | DS-KD-M
Productintercom system
EAN0842571124774, 6954273691516
LanguageEnglish
FiletypeUser manual (PDF), Quickstart Guide (PDF)
Features
Product typeCard reader
Product colorBlack
Brand compatibilityHikvision
International Protection (IP) codeIP65
Mounting typeSurface
Packaging data
Quantity per pack1 pc(s)
Package weight421 g
Weight & dimensions
Depth33.7 mm
Height100 mm
Width98.5 mm
Weight160 g
Operational conditions
Operating temperature (T-T)-40 - 55 °C
Storage temperature (T-T)10 - 95 °C
Power
DC input voltage12 V
Technical details
Sustainability certificatesREACH, RoHS, WEEE
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Hikvision DS-KD-M below.

What is the weight of the Hikvision DS-KD-M?

The Hikvision DS-KD-M has a weight of 160 g.

What is the height of the Hikvision DS-KD-M?

The Hikvision DS-KD-M has a height of 100 mm.

What is the width of the Hikvision DS-KD-M?

The Hikvision DS-KD-M has a width of 98.5 mm.

What is the depth of the Hikvision DS-KD-M?

The Hikvision DS-KD-M has a depth of 33.7 mm.

Is Hikvision DS-KD-M a card reader?

Yes, Hikvision DS-KD-M is a card reader, making it ideal for secure access control systems.

What is the DC input voltage for Hikvision DS-KD-M?

The DC input voltage for Hikvision DS-KD-M is 12 V, providing stable and reliable power for the system.

What is the International Protection (IP) code for Hikvision DS-KD-M?

The International Protection (IP) code for Hikvision DS-KD-M is IP65, indicating that it is dust-tight and protected against water jets, making it suitable for outdoor use.

How is Hikvision DS-KD-M mounted?

Hikvision DS-KD-M is mounted using a surface mounting type, making installation quick and easy.

Does Hikvision DS-KD-M have any sustainability certificates?

Yes, Hikvision DS-KD-M has sustainability certificates including REACH, RoHS, and WEEE, indicating that it meets strict environmental standards and regulations.

What should I do if I encounter issues while setting and confirming the encryption password for exporting parameters?

To resolve issues while setting and confirming the encryption password for exporting parameters on the Hikvision DS-KD-M intercom system, follow these steps: 1. Select "Device Parameters" and click "Export" to open the dialog box. 2. Set and confirm the encryption password in the dialog box. 3. Click "OK" to export the parameters. Remember to choose a strong password with a minimum of 8 characters, including uppercase letters, lowercase letters, numbers, and special characters. It is advisable to change your password regularly for enhanced security.

How long does the upgrading process typically take, and what should I avoid doing during the upgrade?

To upgrade the Hikvision DS-KD-M intercom system, follow these steps: - Click on the browse icon to select the upgrade file. - The upgrading process typically lasts between 1 to 10 minutes. - Avoid powering off the device during the upgrade to prevent interruptions. - The device will reboot automatically after the upgrade is complete. - Ensure not to interrupt the process to avoid any potential issues. - It is recommended to create a strong password with a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters. - Change your password regularly for increased security, especially in high-security systems. - Enable SSH in the Security Service settings according to your needs. - Edit user permissions in the User Management settings. - Regularly check online users and manage them accordingly.

Is the manual of the Hikvision DS-KD-M available in English?

Yes, the manual of the Hikvision DS-KD-M is available in English .

Is your question not listed? Ask your question here

No results