Hikvision DS-KD-KK manual

Hikvision DS-KD-KK
7.8 · 1
PDF manual
 · 100 pages
English
manualHikvision DS-KD-KK

DS-KD-KK DS-KD-M(E)

Video Intercom Module Door Staon UD21094B-AENGLISHDiagram References
1
Call Buon
2
Card Reading Area
3
4
5
Module-connecng Interface (Output)
6
Debugging Port
Note: The module-connecng interface is used to connect other funcon module, such as nametag module,
keypad module, card reader module, etc. All these modules are known as sub module.
Appearance
1
1
Nametag
Terminal
2
A1
A2
A3
A4
485-: Module-connecng Interface (Input)
B1
B2
B3
B4
Installaon
3
Note: Video intercom module door staon support one-module installaon, two-module installaon, three-
module installaon and more-than-three-module installaon. Here takes three-module installaon as an
example.
Tools that you need to prepare for installaon: Drill(6), cross screw driver (PH1*150
mm), and gradienter.
Make sure all the related equipment is power-off during the installaon.
Make sure you have configured the sub module address before installaon. Valid sub
module address range is 1 to 8. The No. should be unique for sub modules that
connected to the same main unit. The sub module address and corresponding switch
status is shown as the figure.
Before You StartThree-Module Flush Mounng
1. Cave the installaon hole, and pull the cable out.
Note: The suggested dimension of the installaon hole is 321.8(W) × 108(H) × 45.5(D) mm. The suggested
length of the cables le outside is 270 mm.
2. Select a cable entry and remove the plasc sheet. Route the cables through the gang
box hole. Insert the gang box into the installaon hole. Mark the gang box screw holes’
posion with a marker, and take out the gang box.
3. Drill 4 holes according to the marks on the wall, and insert the expansion sleeves into
the screw holes. Fix the gang box with 4 expansion bolts.
4. Fill the gap between the gang box and wall with concrete or Silicone sealant. Remove
the mounng ears with tool aer concrete is dry.
5. Connect cables and insert the modules.
a.Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the main
unit, then insert the main unit into the upper grid.
b.Connect the other end of Cable 2 to the input interface of Sub Module 1. Connect
one end of Sub Module 1 and insert it into the middle grid.
c.Connect the other end of Cable 3 to the input interface of Sub Module 2. Insert it
into the boom grid.
6. Fix the cover and the main unit with 2 socket head cap screws by using a hexagon
wrench.
Surface Mounng with Protecve Shield
1. Paste the installaon scker 1 onto the wall. Make sure the scker is placed
horizontally via measuring with the gradienter. Drill 4 holes according to the screw holes
on the scker.
Note: The suggested size of hole is 6(diameter) × 25(depth) mm. The suggested length of the cables le
outside is 270 mm.
2. Remove the scker and insert the expansion sleeves into the screw holes. Fix the
mounng frame
onto the wall with 4 expansion bolts.
3. Thread the module-connecng line across the thread holes of the frame. Pass the
main unit
connecng line across the thread hole to the top grid and connect the cables.
a.Connect the lines and module-connecng line 1 to the corresponding interfaces of
the main unit,
then place the main unit into the upper grid.
b.Connect the other end of the module-connecng line 1 to the input interface of the
sub modules via module-connecng line 2.
c.Organize the cables with cable e in the package.
4. Insert the modules into the frame aer wiring. The main unit must be placed in the
top grid.
5. Use the hexagon wrench in the package to fix the cover onto the frame.
Gang Box

1 2 3 4 5 6

13

Expansion BoltMounng EarMain UnitSub Module 1Sub Module 2HexagonalScrew
1
2
2
2
1
3
3
3

13

1
2
3
4
5 6
2
Module-connecng Interface (Input)
A1 A4 B4B1
GND
12V OUT
485+
485-
GND
12V IN
485+
485-
RS485 IN RS485 OUT
485+: Module-connecng Interface (Input)
12V IN: Module-connecng Interface (Input)
GND: Module-connecng Interface (Input)
485-: Module-connecng Interface (Output)
485+: Module-connecng Interface (Output)
12V IN: Module-connecng Interface (Output)
GND: Module-connecng Interface (Output)
Nametag Module Card Reader Module
1

2 3 4 5

Module-Connecng Line1Module-Connecng Line2Thread HoleCables Connectedto Main ModuleMain UnitSub ModuleMounng FrameHexagonalScrewCoverHexagon Wrench

View the manual for the Hikvision DS-KD-KK here, for free. This manual comes under the category intercom systems and has been rated by 1 people with an average of a 7.8. This manual is available in the following languages: English. Do you have a question about the Hikvision DS-KD-KK or do you need help? Ask your question here

Need help?

Do you have a question about the Hikvision and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Hikvision DS-KD-KK intercom system is a single-pack product designed for use with Hikvision brand compatibility. With dimensions of 98.2 millimeters in width, 33.7 millimeters in depth, and 100.2 millimeters in height, this intercom system is compact and suitable for various installation locations. It has received RoHS, WEEE, and REACH sustainability certificates, underscoring its adherence to environmental standards. The product features an International Protection (IP) code of IP65, indicating dust tightness and protection against water jets. With a weight of 190 grams and a package weight of 438 grams, this intercom system is lightweight and easy to handle during installation. It operates on a DC input voltage of 12 volts, providing power efficiency for electronic communication. The KD8 Series Pro Modular Door Station features a sleek design and is suitable for various residential and commercial applications. Its durable construction and reliable performance make it a practical choice for those seeking a functional intercom system.

General
BrandHikvision
ModelDS-KD-KK | DS-KD-KK
Productintercom system
EAN0842571124767, 5420016866899, 6954273689698
LanguageEnglish
FiletypeUser manual (PDF), Quickstart Guide (PDF)
Features
Product colorBlack, Grey, White
Brand compatibilityHikvision
International Protection (IP) codeIP65
Packaging data
Quantity per pack1 pc(s)
Package weight438 g
Operational conditions
Operating temperature (T-T)-40 - 55 °C
Storage temperature (T-T)10 - 95 °C
Weight & dimensions
Width98.2 mm
Depth33.7 mm
Height100.2 mm
Weight190 g
Technical details
Sustainability certificatesRoHS, WEEE, REACH
Power
DC input voltage12 V
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Hikvision DS-KD-KK below.

What is the weight of the Hikvision DS-KD-KK?

The Hikvision DS-KD-KK has a weight of 190 g.

What is the height of the Hikvision DS-KD-KK?

The Hikvision DS-KD-KK has a height of 100.2 mm.

What is the width of the Hikvision DS-KD-KK?

The Hikvision DS-KD-KK has a width of 98.2 mm.

What is the depth of the Hikvision DS-KD-KK?

The Hikvision DS-KD-KK has a depth of 33.7 mm.

Is Hikvision DS-KD-KK suitable for outdoor use?

Yes, with an International Protection (IP) code of IP65, Hikvision DS-KD-KK is suitable for outdoor use, providing protection against dust and water ingress.

What is the DC input voltage requirement for Hikvision DS-KD-KK?

The DC input voltage requirement for Hikvision DS-KD-KK is 12 V, ensuring compatibility with most standard power sources.

Does Hikvision DS-KD-KK come with any sustainability certificates?

Yes, Hikvision DS-KD-KK comes with sustainability certificates including RoHS, WEEE, and REACH, highlighting the brand's commitment to environmentally-friendly practices.

How many pieces are included in a pack of Hikvision DS-KD-KK?

A pack of Hikvision DS-KD-KK includes 1 pc(s), making it suitable for individual use or small-scale installations.

Is Hikvision DS-KD-KK compatible with other brands?

Hikvision DS-KD-KK is specifically designed for Hikvision products, ensuring seamless integration and optimal performance within the brand's ecosystem.

How can I configure the Video Intercom Settings on the Hikvision DS-KD-KK intercom system?

To configure the Video Intercom Settings on the Hikvision DS-KD-KK intercom system, follow these steps: 1. Set the play schedule by selecting a theme and dragging the time interval on the timeline. You can also edit the time manually and delete selected areas if needed. 2. Adjust the Slide Show Interval by setting the slide show interval for changing pictures. 3. Enable show custom content and edit custom content if desired. 4. Add the device to the software and configure the person to link the device in the Access Control module before remote configuration. 5. Go to AccessControlInfo → Video Intercom → Video Intercom to enter the Video Intercom page. 6. To receive a call from the door station, select the client software to start calling, answer the call by clicking Answer, or decline it by clicking Hang Up. These steps will help you configure the Video Intercom Settings on your Hikvision DS-KD-KK intercom system.

What should I do if I encounter issues receiving a call from the door station on the Hikvision DS-KD-KK intercom system?

To resolve issues receiving a call from the door station on the Hikvision DS-KD-KK intercom system, follow these steps: 1. Set the Main Station IP and Video Intercom Server IP. 2. Enable Protocol 1.0. 3. Configure the maximum call duration, message duration, and ring duration in the Time Parameters settings. 4. Set the Ring-Back Tone by selecting a ring tone from the PC. 5. Go to Press Button to Call settings and configure as needed. 6. Click Save to apply the settings. 7. Select a picture to be played in standby mode and set the play schedule. 8. Adjust the Slide Show Interval for the picture display. 9. Optionally enable and edit custom content. 10. Use the Video Intercom Management module in the iVMS-4200 Client Software to receive calls from the door station. Answer or decline calls as needed.

How can I configure the Video Intercom Settings on the Hikvision DS-KD-KK intercom system?

To configure the Video Intercom Settings on the Hikvision DS-KD-KK intercom system, follow these steps: 1. Set the play schedule by selecting a theme and dragging the time interval on the timeline. You can also edit the time manually and delete selected areas if needed. 2. Adjust the Slide Show Interval by setting the interval for changing pictures. 3. Enable show custom content and edit custom content if desired for display on the main page of the device. 4. Add the device to the software and configure the person to link the device in the Access Control module before remote configuration. 5. Access the Video Intercom page by clicking on AccessControlInfo → Video Intercom on the left bar of the main page. 6. To receive a call from the door station, select the client software to start calling, answer the call by clicking Answer, or decline it by clicking Hang Up.

What should I do if I am unable to receive a call from the door station on the Hikvision DS-KD-KK intercom system?

To troubleshoot the issue of being unable to receive a call from the door station on the Hikvision DS-KD-KK intercom system, follow these steps: 1. Set the Main Station IP and Video Intercom Server IP. 2. Enable Protocol 1.0. 3. Click Save to apply the settings. 4. Configure the Max. Call Duration, Max. Message Duration, and Max. Ring Duration in the Time Parameters section. 5. Save the configured time parameters. 6. Check the Ring-Back Tone Settings and select a suitable ring tone from the PC. 7. Navigate to the Press Button to Call settings and ensure the configurations are correct. These steps should help resolve the issue of not being able to receive calls from the door station on the Hikvision DS-KD-KK intercom system.

Is the manual of the Hikvision DS-KD-KK available in English?

Yes, the manual of the Hikvision DS-KD-KK is available in English .

Is your question not listed? Ask your question here

No results