Hikvision DS-KD-DIS manual

Hikvision DS-KD-DIS
9.2 · 1
PDF manual
 · 100 pages
English
manualHikvision DS-KD-DIS

DS-KD-DIS DS-KD-KP

Video Intercom Module Door Staon UD20201B-AENGLISHDiagram References
1
Screen
2
Down Buon
3
Confirm Buon
4
5
Module-connecng Interface (Output)
6
7
Debugging Port
8
Note: The module-connecng interface is used to connect other funcon module, such as nametag module,
keypad module, card reader module, etc. All these modules are known as sub module.
Appearance
1
1
Up Buon
Back Buon
Terminal
2
A1
A2
A3
A4
485-: Module-connecng Interface (Input)
B1
B2
B3
B4
Installaon
3
Note: Video intercom module door staon support one-module installaon, two-module installaon, three-
module installaon and more-than-three-module installaon. Here takes three-module installaon as an
example.
Tools that you need to prepare for installaon: Drill(6), cross screw driver (PH1*150
mm), and gradienter.
Make sure all the related equipment is power-off during the installaon.
Make sure you have configured the sub module address before installaon. Valid sub
module address range is 1 to 8. The No. should be unique for sub modules that
connected to the same main unit. The sub module address and corresponding switch
status is shown as the figure.
Before You StartThree-Module Flush Mounng
1. Cave the installaon hole, and pull the cable out.
Note: The suggested dimension of the installaon hole is 321.8(W) × 108(H) × 45.5(D) mm. The suggested
length of the cables le outside is 270 mm.
2. Select a cable entry and remove the plasc sheet. Route the cables through the gang
box hole. Insert the gang box into the installaon hole. Mark the gang box screw holes’
posion with a marker, and take out the gang box.
3. Drill 4 holes according to the marks on the wall, and insert the expansion sleeves into
the screw holes. Fix the gang box with 4 expansion bolts.
4. Fill the gap between the gang box and wall with concrete or Silicone sealant. Remove
the mounng ears with tool aer concrete is dry.
5. Connect cables and insert the modules.
a.Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the main
unit, then insert the main unit into the upper grid.
b.Connect the other end of Cable 2 to the input interface of Sub Module 1. Connect
one end of Sub Module 1 and insert it into the middle grid.
c.Connect the other end of Cable 3 to the input interface of Sub Module 2. Insert it
into the boom grid.
6. Fix the cover and the main unit with 2 socket head cap screws by using a hexagon
wrench.
Surface Mounng with Protecve Shield
1. Paste the installaon scker 1 onto the wall. Make sure the scker is placed
horizontally via measuring with the gradienter. Drill 4 holes according to the screw holes
on the scker.
Note: The suggested size of hole is 6(diameter) × 25(depth) mm. The suggested length of the cables le
outside is 270 mm.
2. Remove the scker and insert the expansion sleeves into the screw holes. Fix the
mounng frame
onto the wall with 4 expansion bolts.
3. Thread the module-connecng line across the thread holes of the frame. Pass the
main unit
connecng line across the thread hole to the top grid and connect the cables.
a.Connect the lines and module-connecng line 1 to the corresponding interfaces of
the main unit,
then place the main unit into the upper grid.
b.Connect the other end of the module-connecng line 1 to the input interface of the
sub modules via module-connecng line 2.
c.Organize the cables with cable e in the package.
4. Insert the modules into the frame aer wiring. The main unit must be placed in the
top grid.
5. Use the hexagon wrench in the package to fix the cover onto the frame.
Gang Box

1 2 3 4 5 6

13

1

2 3 4 5

Expansion BoltMounng EarMain UnitSub Module 1Sub Module 2HexagonalScrew
1
2
2
2
1
3
3
3
Module-Connecng
Line1
Module-Connecng
Line2
Thread Hole
Cables Connected
to Main Module
Main Unit
Sub Module
Mounng Frame
HexagonalScrewCoverHexagon Wrench

13

1
2
3
4
5
6
7 8
2
Module-connecng Interface (Input)
A1 A4 B4B1
GND
12V OUT
485+
485-
GND
12V IN
485+
485-
RS485 IN RS485 OUT
485+: Module-connecng Interface (Input)
12V IN: Module-connecng Interface (Input)
GND: Module-connecng Interface (Input)
485-: Module-connecng Interface (Output)
485+: Module-connecng Interface (Output)
12V IN: Module-connecng Interface (Output)
GND: Module-connecng Interface (Output)
9
Display Module Keypad Module
Keypad
9

View the manual for the Hikvision DS-KD-DIS here, for free. This manual comes under the category intercom systems and has been rated by 1 people with an average of a 9.2. This manual is available in the following languages: English. Do you have a question about the Hikvision DS-KD-DIS or do you need help? Ask your question here

Need help?

Do you have a question about the Hikvision and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Hikvision DS-KD-DIS intercom system is a communication device designed for secure entry control in various settings. It features a durable and sleek design that is suitable for both indoor and outdoor installations. The intercom system allows for clear two-way audio communication between a visitor and the user, ensuring effective and reliable communication. Equipped with a high-definition camera, the Hikvision DS-KD-DIS provides crisp video streaming for visual verification of visitors. The system also offers infrared night vision capabilities for enhanced security during low-light conditions. Additionally, it is equipped with noise suppression and echo cancellation technology to ensure clear audio quality even in noisy environments. The Hikvision DS-KD-DIS intercom system is compatible with other Hikvision products, allowing for seamless integration with existing security systems. It also supports remote access through mobile devices, enabling users to monitor and control access from anywhere at any time. Overall, the Hikvision DS-KD-DIS intercom system is a reliable and effective solution for enhancing security and communication in various settings.

General
BrandHikvision
ModelDS-KD-DIS
Productintercom system
LanguageEnglish
FiletypeUser manual (PDF), Quickstart Guide (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Hikvision DS-KD-DIS below.

Is the manual of the Hikvision DS-KD-DIS available in English?

Yes, the manual of the Hikvision DS-KD-DIS is available in English .

Is your question not listed? Ask your question here

No results