Hikvision DS-K2802 manual

Hikvision DS-K2802
9 · 4
PDF manual
 · 88 pages
English
manualHikvision DS-K2802
Access Controller·User Manual
i
User Manual
©2018 Hangzhou Hikvision Digital Technology Co., Ltd.
This manual is applied for access controller.
Product Name
Serials
Access
Controller
DS-K2801 Serials Access Controller
DS-K2802 Serials Access Controller
DS-K2804 Serials Access Controller
It includes instructions on how to use the Product. The software embodied in the Product is
governed by the user license agreement covering that Product.
About this Manual
This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision
Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This manual cannot be
reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior
written permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are registered trademarks
or the subject of applications for the same by Hikvision and/or its affiliates. Other trademarks
mentioned in this manual are the properties of their respective owners. No right of license is given
to use such trademarks without express permission.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL.
HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE
USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION
CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE
WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY
AT YOUR OWN RISKS. OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER
ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, OUR COMPANY WILL
PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE
APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED
WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER
PREVAILS.
Support
Should you have any questions, please do not hesitate to contact your local dealer.

View the manual for the Hikvision DS-K2802 here, for free. This manual comes under the category intercom systems and has been rated by 4 people with an average of a 9. This manual is available in the following languages: English. Do you have a question about the Hikvision DS-K2802 or do you need help? Ask your question here

Need help?

Do you have a question about the Hikvision and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Hikvision DS-K2802 is an access controller intercom system designed for seamless integration with Wiegand-compatible devices. With dimensions of 237 millimeters in width, 285 millimeters in depth, and 69 millimeters in height, this wall-mounted system is certified by CE and FCC for quality assurance. Specifically tailored for use with Hikvision brand products, the DS-K2802 ensures compatibility and easy setup within existing security systems. As an access controller, it provides a reliable means of managing entry points and regulating access within a designated area. Constructed with durability in mind, the DS-K2802 is built to withstand long-term use and ensure consistent performance. Each pack contains 1 piece of this access controller, offering a singular solution for enhancing security measures in various settings. Ideal for commercial or residential applications, the Hikvision DS-K2802 offers a practical and efficient solution for controlling access and maintaining security. With its reliable construction and certifications, it provides peace of mind for users seeking a dependable access control system.

General
BrandHikvision
ModelDS-K2802 | DS-K2802
Productintercom system
EAN6954273635657
LanguageEnglish
FiletypeUser manual (PDF), Quickstart Guide (PDF)
Weight & dimensions
Width237 mm
Depth285 mm
Height69 mm
Features
CompatibilityWiegand
Product colorBlack
Brand compatibilityHikvision
CertificationCE, FCC
Product typeAccess controller
Mounting typeWall
Operational conditions
Operating temperature (T-T)-20 - 65 °C
Packaging data
Quantity per pack1 pc(s)
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Hikvision DS-K2802 below.

What certifications does the Hikvision DS-K2802 have?

The Hikvision DS-K2802 has the following certifications: CE, FCC.

What is the height of the Hikvision DS-K2802?

The Hikvision DS-K2802 has a height of 69 mm.

What is the width of the Hikvision DS-K2802?

The Hikvision DS-K2802 has a width of 237 mm.

What is the depth of the Hikvision DS-K2802?

The Hikvision DS-K2802 has a depth of 285 mm.

Is Hikvision DS-K2802 compatible with Wiegand?

Yes, Hikvision DS-K2802 is compatible with Wiegand. This means that it can work with other devices that use the same communication protocol, providing seamless integration in a security system.

Is Hikvision DS-K2802 compatible with other Hikvision products?

Yes, Hikvision DS-K2802 is specifically designed to be compatible with other Hikvision products. This ensures a smooth and efficient operation when used within a Hikvision ecosystem.

What type of product is Hikvision DS-K2802?

Hikvision DS-K2802 is an access controller. This means it is responsible for controlling access to a particular area, such as a building or room, by granting or denying entry based on authorized credentials.

Can Hikvision DS-K2802 be mounted on a wall?

Yes, Hikvision DS-K2802 can be mounted on a wall. This allows for easy installation and placement in a convenient location, ensuring accessibility for authorized personnel.

How many units of Hikvision DS-K2802 are included in a pack?

Each pack of Hikvision DS-K2802 contains 1 unit. This indicates that the product is sold individually and not in bulk quantities, making it suitable for specific installation requirements.

How can I reset the Hikvision DS-K2802 intercom system to its factory settings?

To reset the Hikvision DS-K2802 intercom system to its factory settings, follow these steps: 1. Access the Remote Configuration interface by clicking on "System" and then "System Maintenance". 2. In the System Maintenance section, you will find different options for system settings. 3. To reset the device to its default settings, click on "Restore Default Settings". This will restore all the device settings to their original factory defaults, except for the IP address. 4. Alternatively, you can click on "Restore All" to restore all the device parameters to their default values. After restoring, the device should be activated again. 5. If you want to reboot the device, click on "Reboot". This will restart the device. 6. Additionally, you have the option to perform a remote upgrade of the device. In the Remote Upgrade section, select the type of upgrade file (Controller Upgrade File or Card Reader Upgrade) and click on "Upgrade" to start the upgrading process. Note that only card readers connected via RS-485 can be upgraded. Please note that the configuration file contains the device parameters, and the DS-K2800 series access controller only supports Wiegand card readers for upgrading.

Why is the Hikvision DS-K2802 intercom system not turning on?

There could be several reasons why the Hikvision DS-K2802 intercom system is not turning on. Here are some possible causes and troubleshooting steps: 1. Power Supply: Check if the power adapter is properly connected to the intercom system and the power source. Ensure that the power adapter is providing the correct voltage and current as specified in the manual. 2. Power Outlet: Verify that the power outlet is functioning correctly by plugging in another device. If the outlet is not working, try using a different outlet or check the circuit breaker. 3. Power Adapter Issue: If the power adapter is not working, try using a different power adapter with the same voltage and current specifications. 4. Faulty Wiring: Inspect the wiring connections between the intercom system and the power source. Ensure that all connections are secure and there are no loose or damaged wires. 5. Device Malfunction: If none of the above steps resolve the issue, there may be a malfunction with the intercom system itself. In this case, it is recommended to contact your dealer or the nearest service center for further assistance. Please note that these troubleshooting steps are general guidelines, and it is always advisable to refer to the specific instructions provided in the manual for the Hikvision DS-K2802 intercom system.

How do I properly install the Hikvision DS-K2802 intercom system on a wall?

To properly install the Hikvision DS-K2802 intercom system on a wall, follow these steps: 1. Ensure that the installation location is suitable, providing a well-ventilated and dust-free environment for the intercom system. 2. Securely mount the intercom system on the wall using the provided mounting brackets and screws. Make sure the device is firmly fixed to prevent accidents or damage. 3. Connect the necessary cables to the appropriate ports on the intercom system. Refer to the manual for the specific cable connections required for your installation. 4. Ensure that the power has been disconnected before wiring or installing the device. This is important for safety reasons. 5. Once the intercom system is securely mounted and the cables are properly connected, restore power to the device. 6. Test the functionality of the intercom system by following the instructions provided in the manual for setup and configuration. Please note that these steps are general guidelines for installing the Hikvision DS-K2802 intercom system on a wall. For detailed instructions and specific requirements, refer to the manual provided with the product.

What should I do if the Hikvision DS-K2802 intercom system is not functioning properly after installation?

If the Hikvision DS-K2802 intercom system is not functioning properly after installation, follow these steps for troubleshooting: 1. Check the power supply: Ensure that the power adapter is properly connected and providing the correct voltage and current as specified in the manual. Make sure the power outlet is functioning correctly. 2. Verify the wiring connections: Inspect the wiring connections between the intercom system and other devices or components. Ensure that all connections are secure and properly connected. 3. Restart the system: Try restarting the intercom system by disconnecting the power supply, waiting for a few seconds, and then reconnecting it. This can help resolve temporary issues. 4. Reset the system: If the problem persists, you can try resetting the intercom system to its factory settings. Refer to the manual for specific instructions on how to perform a reset. 5. Contact support: If none of the above steps resolve the issue, it is recommended to contact your dealer or the nearest service center for further assistance. They can provide specialized support and guidance to troubleshoot and resolve any technical issues. Please note that these troubleshooting steps are general guidelines, and it is always advisable to refer to the specific instructions provided in the manual for the Hikvision DS-K2802 intercom system.

How do I clean the Hikvision DS-K2802 intercom system without damaging it?

To clean the Hikvision DS-K2802 intercom system without damaging it, follow these steps: 1. Power off the intercom system and disconnect it from the power source to ensure safety during the cleaning process. 2. Use a soft, lint-free cloth or microfiber cloth to gently wipe the exterior surfaces of the intercom system. Avoid using abrasive materials or harsh chemicals that may scratch or damage the device. 3. For stubborn dirt or stains, dampen the cloth with a mild, non-abrasive cleaning solution or water. Do not spray liquid directly onto the device; instead, apply the solution to the cloth and then wipe the surface. 4. Pay special attention to the buttons, display screen, and speaker areas. Use a soft brush or cotton swab to clean hard-to-reach areas and remove any debris or dust. 5. Allow the intercom system to dry completely before reconnecting it to the power source. Ensure that no moisture remains on the device to prevent any potential damage. Remember to always follow the manufacturer's guidelines and recommendations for cleaning the Hikvision DS-K2802 intercom system.

Is the manual of the Hikvision DS-K2802 available in English?

Yes, the manual of the Hikvision DS-K2802 is available in English .

Is your question not listed? Ask your question here

No results