Hikvision DS-K2801 manual

Hikvision DS-K2801
8.7 · 2
PDF manual
 · 88 pages
English
manualHikvision DS-K2801

Access Controller·User Manual

79

Appendix B Custom Wiegand Rule

Take Wiegand 44 as an example, the setting values in the Custom Wiegand tab are as follows:
Custom Wiegand Name:
Wiegand 44
Total Length
44
Transformation Rule (Decimal Digit)
byFormatRule[4]=[1][4][0][0]
Parity Mode
XOR Parity
Odd Parity Start Bit
Length
Even Parity Start Bit
Length
XOR Parity Start Bit
0
Length per Group
4
Total Length
Card ID Start Bit
0
Length
32
Decimal Digit
10
Site Code Start Bit
Length
Decimal Digit
OEM Start Bit
Length
Decimal Digit
Manufacturer Code Start Bit
32
Length
8
Decimal Digit
3
Wiegand Data = Valid Data + Parity Data
Total Length: Wiegand data length.
Transportation Rule: 4 bytes. Display the combination types of valid data. The example displays the combination
of Card ID and Manufacturer Code. The valid data can be single rule, or combination of multiple rules.
Parity Mode: Valid parity for wiegand data. You can select either odd parity or even parity.
Odd Parity Start Bit, and Length: If you select Odd Parity, these items are available. If the odd parity start bit is 1,
and the length is 12, then the system will start odd parity calculation from bit 1. It will calculate 12 bits. The result
will be in bit 0. (Bit 0 is the first bit.)
Even Parity Start Bit, and Length: If you select Even Parity, these items are available. If the even parity start bit is
12, and the length is 12, then the system will start even parity calculation from bit 12. It will calculate 12 bits. The
result will be in the last bit.
XOR Parity Start Bit, Length per Group, and Total Length: If you select XOR Parity, these items are available.
Depending on the table displayed above, the start bit is 0, the length per group is 4, and the total length is 40. It
means that the system will calculate from bit 0, calculate every 4 bit, and calculate 40 bits in total (10 groups in
total). The result will be in the last 4 bits. (The result length is the same as the length per group.)
Card ID Start Bit, Length, and Decimal Digit: If you use the transformation rule, these items are available.
Depending on the table displayed above, the card ID start bit is 0, the length is 32, and the decimal digit is 10. It
represents that from bit 0, there are 32 bits represent the card ID. (The length here is calculated by bit.) And the
decimal digit length is 10 bits.
Site Code Start Bit, Length, and Decimal Digit: If you use the transformation rule, these items are available. For
detailed information, see the explanation of the card ID.
OEM Start Bit, Length, and Decimal Digit: If you use the transformation rule, these items are available. For detailed
information, see the explanation of the card ID.
Manufacturer Code Start Bit, Length, and Decimal Digit: If you use the transformation rule, these items are
available. Depending on the table displayed above, the manufacturer code start bit is 32, length is 8, and decimal
digit is 3. It represents that from bit 32, there are 8 bits are manufacturer code. (The length here is calculated by
bit.) And the decimal length is 3.

020000001080620

View the manual for the Hikvision DS-K2801 here, for free. This manual comes under the category intercom systems and has been rated by 2 people with an average of a 8.7. This manual is available in the following languages: English. Do you have a question about the Hikvision DS-K2801 or do you need help? Ask your question here

Need help?

Do you have a question about the Hikvision and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

General
BrandHikvision
ModelDS-K2801 | DS-K2801
Productintercom system
EAN6954273635640
LanguageEnglish
FiletypeUser manual (PDF), Quickstart Guide (PDF)
Weight & dimensions
Width237 mm
Depth285 mm
Height69 mm
Features
Brand compatibilityHikvision
Product colorBlack
CompatibilityWiegand
CertificationCE, FCC
Product typeAccess controller
Mounting typeWall
Operational conditions
Operating temperature (T-T)-20 - 65 °C
Packaging data
Quantity per pack1 pc(s)
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Hikvision DS-K2801 below.

What certifications does the Hikvision DS-K2801 have?

The Hikvision DS-K2801 has the following certifications: CE, FCC.

What is the height of the Hikvision DS-K2801?

The Hikvision DS-K2801 has a height of 69 mm.

What is the width of the Hikvision DS-K2801?

The Hikvision DS-K2801 has a width of 237 mm.

What is the depth of the Hikvision DS-K2801?

The Hikvision DS-K2801 has a depth of 285 mm.

Is the Hikvision DS-K2801 compatible with other brands?

Yes, the Hikvision DS-K2801 is compatible with other brands.

Does the Hikvision DS-K2801 support Wiegand?

Yes, the Hikvision DS-K2801 supports Wiegand.

What type of product is the Hikvision DS-K2801?

The Hikvision DS-K2801 is an access controller.

How many units are included in a pack of the Hikvision DS-K2801?

A pack of the Hikvision DS-K2801 includes 1 unit.

What is the mounting type of the Hikvision DS-K2801?

The Hikvision DS-K2801 has a wall mounting type.

How can I troubleshoot if the Hikvision DS-K2801 intercom system is not powering on?

To troubleshoot if the Hikvision DS-K2801 intercom system is not powering on, you can follow these steps: 1. Check the power supply: Ensure that the power adapter is properly connected to the intercom system and the power source. Make sure the power adapter is functioning correctly and providing the correct voltage. 2. Verify the power switch: Check if the power switch on the intercom system is turned on. Sometimes, it may accidentally get switched off. 3. Reset the intercom system: If the system is unresponsive, you can try resetting it. To do this, disconnect the power supply, wait for a few seconds, and then reconnect it. This can help resolve any temporary issues. 4. Check the power source: Ensure that the power source you are using is working correctly. Try plugging in another device to the same power source to verify if it is functioning properly. 5. Contact customer support: If the above steps do not resolve the issue, it is recommended to contact Hikvision customer support for further assistance. They can provide specific troubleshooting steps or arrange for repairs if necessary. Remember to always follow safety precautions and refer to the user manual for any specific instructions related to your Hikvision DS-K2801 intercom system.

What should I do if the Hikvision DS-K2801 intercom system is not functioning properly after connecting multiple devices to one power adapter?

To troubleshoot if the Hikvision DS-K2801 intercom system is not functioning properly after connecting multiple devices to one power adapter, you can follow these steps: 1. Ensure electrical safety: Make sure that all electronic operations comply with electrical safety regulations, fire prevention regulations, and other related regulations in your local region. 2. Use the correct power adapter: Use the power adapter provided by the company and ensure that its power consumption meets the required value. Do not connect several devices to one power adapter as it may cause overload, overheat, or fire hazard. 3. Firmly fix the device: If the intercom system is installed on a wall or ceiling, ensure that it is firmly fixed to prevent vibrations or shocks that can cause equipment damage. 4. Check for smoke, odors, or noise: If any smoke, odors, or unusual noise arise from the device, immediately turn off the power, unplug the power cable, and contact the service center. 5. Contact the dealer or service center: If the intercom system still does not work properly after following the above steps, it is recommended to contact your dealer or the nearest service center for further assistance. Do not attempt to disassemble the device yourself. Remember to always prioritize safety and consult the user manual for any specific instructions related to your Hikvision DS-K2801 intercom system.

How can I troubleshoot if the Hikvision DS-K2801 intercom system is not securely fixed on the wall or ceiling?

To troubleshoot if the Hikvision DS-K2801 intercom system is not securely fixed on the wall or ceiling, you can follow these steps: 1. Ensure firm fixing: Check if the intercom system is securely mounted on the wall or ceiling. Make sure that all screws and brackets are properly tightened to prevent any movement or instability. 2. Verify the installation surface: Ensure that the surface where the intercom system is installed is suitable for mounting. Avoid installing it on vibrating surfaces or places subject to shock, as this can cause damage to the equipment. 3. Use appropriate mounting hardware: Use the recommended screws and brackets provided by Hikvision for mounting the intercom system. Ensure that the chosen hardware is suitable for the type of surface and can provide a secure hold. 4. Check for any loose components: Inspect the intercom system for any loose components or connections. Tighten any loose screws or connectors to ensure a secure fit. 5. Seek professional assistance if needed: If you are unable to securely fix the intercom system or if you have any doubts about the installation process, it is recommended to seek professional assistance from a qualified technician or contact Hikvision customer support for further guidance. Remember to always prioritize safety and refer to the user manual for any specific instructions related to securely fixing the Hikvision DS-K2801 intercom system on the wall or ceiling.

What should I do if the Hikvision DS-K2801 intercom system is not operating within the specified temperature range?

To troubleshoot if the Hikvision DS-K2801 intercom system is not operating within the specified temperature range, you can follow these steps: 1. Check the operating temperature range: Refer to the specifications in the user manual to determine the recommended operating temperature range for the DS-K2801 intercom system. 2. Ensure proper ventilation: Make sure that the intercom system is installed in a well-ventilated area. Ensure that there is sufficient airflow around the device to prevent overheating. 3. Remove any obstructions: Check for any obstructions around the intercom system that may be blocking airflow. Remove any objects or debris that may be hindering proper ventilation. 4. Avoid extreme temperatures: Ensure that the intercom system is not exposed to extreme temperatures outside the specified operating range. Avoid placing it in areas that are too hot, cold, dusty, or damp. 5. Contact customer support: If the intercom system continues to have temperature-related issues, it is recommended to contact Hikvision customer support for further assistance. They can provide specific troubleshooting steps or arrange for repairs if necessary. Remember to always refer to the user manual for any specific instructions related to the operating temperature range and maintenance of the Hikvision DS-K2801 intercom system.

How can I troubleshoot if the Hikvision DS-K2801 intercom system is not functioning properly after exposure to moisture or direct sunlight?

To troubleshoot if the Hikvision DS-K2801 intercom system is not functioning properly after exposure to moisture or direct sunlight, you can follow these steps: 1. Avoid direct sunlight: Ensure that the intercom system is not exposed to direct sunlight for prolonged periods. Direct sunlight can cause overheating and damage to the device. Install the intercom system in a shaded area if possible. 2. Protect from moisture: Prevent the intercom system from being exposed to moisture or water. Moisture can damage the internal components and affect the performance of the device. Install the intercom system in a dry location and avoid placing it near water sources. 3. Check for signs of damage: Inspect the intercom system for any visible signs of damage or corrosion caused by exposure to moisture or direct sunlight. If you notice any damage, contact Hikvision customer support for further assistance. 4. Clean the device properly: Use a soft and dry cloth to clean the intercom system's surfaces. Avoid using alkaline detergents or abrasive materials that can damage the device. 5. Contact customer support: If the intercom system continues to have issues after following the above steps, it is recommended to contact Hikvision customer support for further troubleshooting and assistance. Remember to always prioritize the protection of the intercom system from moisture and direct sunlight to ensure its proper functioning and longevity.

Is the manual of the Hikvision DS-K2801 available in English?

Yes, the manual of the Hikvision DS-K2801 is available in English .

Is your question not listed? Ask your question here

No results