Hikvision DS-2CD2645FWD-IZS manual

Hikvision DS-2CD2645FWD-IZS
5.3 · 1
PDF manual
 · 114 pages
English
manualHikvision DS-2CD2645FWD-IZS

Safety Instrucon

These instrucons are intended to ensure that user can use the product correctly to avoid danger
or property loss.

Laws and Regulaons

The device should be used in compliance with local laws, electrical safety regulaons, and re
prevenon regulaons.

Electricity

In the use of the product, you must be in strict compliance with the electrical safety regulaons
of the naon and region.
The equipment shall not be exposed to dripping or splashing and that no objects lled with
liquids, such as vases, shall be placed on the equipment.
Provide a surge suppressor at the inlet opening of the equipment under special condions such
as the mountain top, iron tower, and forest.
CAUTION: To reduce the risk of re, replace only with the same type and rang of fuse.
The equipment must be connected to an earthed mains socket-outlet.
An appropriate readily accessible disconnect device shall be incorporated external to the
equipment.
An appropriate overcurrent
protecve device shall be incorporated external to the equipment,
not exceeding the specicaon of the building.
An all-pole mains switch shall be incorporated in the electrical
installaon of the building.
Ensure correct wiring of the terminals for connecon to an AC mains supply.
The equipment has been designed, when required,
modied for connecon to an IT power
distribuon system.

Baery

Do not ingest baery. Chemical burn hazard!
This product contains a coin/buon cell baery. If the coin/buon cell baery is swallowed, it
can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used
baeries away from children.
If the
baery compartment does not close securely, stop using the product and keep it away
from children.
If you think
baeries might have been swallowed or placed inside any part of the body, seek
immediate medical aenon.
CAUTION: Risk of explosion if the
baery is replaced by an incorrect type. Dispose of used
baeries according to the instrucons.
ATTENTION: IL Y A RISQUE D'EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR UNE BATTERIE DE
TYPE INCORRECT. METTRE AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX
INSTRUCTIONS.

Network Camera User Manual

vi

Manual

View the manual for the Hikvision DS-2CD2645FWD-IZS here, for free. This manual comes under the category security cameras and has been rated by 1 people with an average of a 5.3. This manual is available in the following languages: English. Do you have a question about the Hikvision DS-2CD2645FWD-IZS or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Hikvision and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Hikvision DS-2CD2645FWD-IZS specifications

Below you will find the product specifications and the manual specifications of the Hikvision DS-2CD2645FWD-IZS.

The Hikvision DS-2CD2645FWD-IZS security camera boasts a total of 4 megapixels, with a maximum resolution of 2688 x 1520 pixels. It features a CMOS sensor with an optical sensor size of 1/2.5 inches, allowing for clear and sharp images. The progressive scan technology ensures smooth video quality without any interlacing. This security camera supports both NTSC and PAL analog signal format systems, providing flexibility for different regions. It has a minimum illumination of 0 lux, enabling it to capture clear images even in low-light conditions. The camera offers a wide angle of rotation of 360 degrees, allowing for comprehensive coverage of the area. With an infrared (IR) cut-off filter and day/night mode, this camera can seamlessly transition between daytime and nighttime surveillance. The IR cut-off filter helps to improve image quality by filtering out unwanted light, while the day/night mode ensures clear and detailed footage regardless of the lighting conditions. Overall, the Hikvision DS-2CD2645FWD-IZS security camera is a reliable and versatile option for monitoring and safeguarding various spaces. Its high-resolution images and advanced features make it a valuable tool for security surveillance.

General
BrandHikvision
ModelDS-2CD2645FWD-IZS | DS-2CD2645FWD-IZS(2.8-12MM)
Productsecurity camera
EAN6954273664176, 0842571118032
LanguageEnglish
FiletypeUser manual (PDF), Quickstart Guide (PDF)
Lens system
Focal length range2.8 - 12 mm
Maximum aperture number1.4
Number of lenses-
Video
Total megapixels4 MP
Maximum resolution2688 x 1520 pixels
Analog signal format systemNTSC, PAL
Noise reductionYes
3D NR (Noise Reduction)Yes
Video compression formatsH.264, H.264+, H.265, H.265+, M-JPEG
Frame rate30 fps
Back Light Compensation (BLC)Yes
Highlight Compensation (HLC)Yes
Region of Interest (ROI) encodingYes
Image quality adjustmentBrightness, Contrast, Saturation, Sharpness
Privacy maskingYes
Image sensor
Sensor typeCMOS
Optical sensor size1/2.5 "
Progressive scanYes
Number of sensors-
Camera
Camera shutter speed1/3 - 100000 s
Minimum illumination0 lx
Tilt angle range0 - 90 °
Pan range0 - 360 °
Angle of rotation360 °
Camera pan control-
Camera tilt control-
Performance
Infrared (IR) cut-off filterYes
Day/night modeYes
Wide Dynamic Range (WDR)Yes
Alarm input/outputYes
Connectivity technologyWired
TypeIP security camera
Placement supportedIndoor & outdoor
Audio
Audio formats supportedG.711, G.722.1, G.726, MP2L2, PCM
Audio input channels1 channels
Audio output channels1 channels
Storage
Card reader integratedYes
Compatible memory cardsMicroSD (TransFlash), MicroSDHC, MicroSDXC
Built-in HDD-
Maximum memory card size128 GB
Security
Video motion detectionYes
Active tampering alarmYes
Anti-flickerYes
HeartbeatYes
Digital watermarkYes
MirrorYes
Password protectionYes
IP address filteringYes
Network
Supported network protocolsTCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, PPPoE, NTP, UPnP, SMTP, SNMP, IGMP, 802.1X, QoS, IPv6, Bonjour
Quality of Service (QoS) supportYes
Networking standardsIEEE 802.1x, IEEE 802.3at
Ethernet LANYes
Wi-Fi-
Bluetooth-
Ethernet interface typeFast Ethernet
Cabling technology10/100Base-T(X)
Number of users32 user(s)
Ports & interfaces
Composite video out1
Ethernet LAN (RJ-45) ports1
InterfaceRJ-45
Management features
Reset buttonYes
Behavior analysisIntrusion detection, Line crossing detection, Object removal detection, Unattended baggage detection
Operational conditions
Operating temperature (T-T)-30 - 60 °C
Operating relative humidity (H-H)0 - 95 %
Power
DC output voltage12
Power source typeDC, PoE
Power consumption (max)14.4 W
Power consumption (Power over Ethernet (PoE))18 W
DC output current1.2 A
Design
WeatherproofYes
International Protection (IP) codeIP67
IK codeIK10
Form factorBullet
Product colorBlack, White
Mounting type-
Night vision
Night vision distance50 m
Night visionYes
LED typeIR
Infra-red wavelength850 nm
Packaging content
Number of cameras1
Weight & dimensions
Width144.1 mm
Length332.7 mm
Weight1893 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Hikvision DS-2CD2645FWD-IZS below.

What is the weight of the Hikvision DS-2CD2645FWD-IZS?

The Hikvision DS-2CD2645FWD-IZS has a weight of 1893 g.

What is a megapixel?

The number of megapixels denotes how many pixels there are in the sensor. 1 megapixel equals 1 million pixels. The more pixels, the higher the potential image quality.

What does the abbreviation 'MP' stand for?

MP stands for MegaPixels.

What is the width of the Hikvision DS-2CD2645FWD-IZS?

The Hikvision DS-2CD2645FWD-IZS has a width of 144.1 mm.

Does the Hikvision DS-2CD2645FWD-IZS have a total of 4 MP?

Yes, the Hikvision DS-2CD2645FWD-IZS has a total of 4 MP. This means that the camera is able to capture high-resolution images and videos, providing clear and detailed footage for the user.

Is the Hikvision DS-2CD2645FWD-IZS equipped with a Progressive scan feature?

Yes, the Hikvision DS-2CD2645FWD-IZS has a Progressive scan feature. This allows for smoother images with reduced flicker, making it suitable for capturing fast-moving objects.

Does the Hikvision DS-2CD2645FWD-IZS have a Wide Dynamic Range (WDR)?

Yes, the Hikvision DS-2CD2645FWD-IZS is equipped with Wide Dynamic Range (WDR). This feature helps balance lighting conditions in scenes with both bright and dark areas, ensuring clear details in the footage.

Does the Hikvision DS-2CD2645FWD-IZS support audio formats such as G.711, G.722.1, and G.726?

Yes, the Hikvision DS-2CD2645FWD-IZS supports audio formats including G.711, G.722.1, and G.726. This allows the user to capture audio along with video, enhancing the overall surveillance capabilities of the camera.

What is the maximum resolution of the Hikvision DS-2CD2645FWD-IZS?

The maximum resolution of the Hikvision DS-2CD2645FWD-IZS is 2688 x 1520 pixels. This high resolution ensures that the user can capture clear and detailed images and videos, making it a competitive option compared to other security cameras on the market.

How can I install and configure third-party applications on the Hikvision DS-2CD2645FWD-IZS security camera using the HEOP (Hikvision Embedded Open Platform)?

To install and configure third-party applications on the Hikvision DS-2CD2645FWD-IZS security camera using the HEOP (Hikvision Embedded Open Platform), follow these steps: 1. Access the camera's settings and navigate to VCA → APP. 2. Select the desired third-party application to install. 3. Follow the instructions to import and run the smart application. 4. Get and install the Hik-Connect application from the official website or app store. 5. Register for a Hik-Connect user account and log in. 6. Scan the QR code of the camera to add it to the Hik-Connect account. 7. Set up the network connection and add the camera to your account. 8. Enable the Hik-Connect service on the camera through SADP software or a web browser. These steps will allow you to successfully install and configure third-party applications on your Hikvision security camera using the HEOP.

What steps should I follow to enable Hik-Connect service on the Hikvision DS-2CD2645FWD-IZS security camera and create a verification code for camera access?

To enable Hik-Connect service on the Hikvision DS-2CD2645FWD-IZS security camera and create a verification code for camera access, follow these steps: 1. Enter the platform access configuration interface by navigating to Configuration → Network → Advanced Settings → Platform Access. 2. Select Hik-Connect as the Platform Access Mode and check Enable. 3. Read and accept the "Terms of Service" and "Privacy Policy" in the pop-up window. 4. Create a verification code for the camera. 5. Save the settings. To enable Hik-Connect service via SADP software: 1. Run the SADP software. 2. Select the camera and enter Modify Network Parameters. 3. Check Enable Hik-Connect. 4. Create or change the verification code. 5. Confirm the settings. To set up Hik-Connect: 1. Install the Hik-Connect application from the official website or app store. 2. Register for a Hik-Connect user account and log in. 3. Scan the QR code of the camera to add it to your account. 4. Follow the prompts to complete the network connection setup.

Is the manual of the Hikvision DS-2CD2645FWD-IZS available in English?

Yes, the manual of the Hikvision DS-2CD2645FWD-IZS is available in English .

Is your question not listed? Ask your question here

No results