Hikvision DS-2AE4215T-A manual

Hikvision DS-2AE4215T-A
6.8 · 1
PDF manual
 · 48 pages
English
manualHikvision DS-2AE4215T-A
HD-TVI Speed Dome User Manual
34
2. Configure the interval of the alarm sequence.
When more than one alarm of the same priority occurs at the same time, the speed dome will
respond to one alarm first and then respond to the next one after the user-defined interval. You
can set the on SEQUENCE submenu from 1 to 200 seconds.
3. Configure the alarm rest delay.
If theres a linkage action has already been triggered by an alarm input, the speed dome will
only respond to the input from the same channel again after the user-defined reset delay time.
This is the rest time that the speed dome considers an alarm to be active when its physically
cleared. You can set the DELAY TIME from 0 to 300 seconds.
4. Resume the dome activity.
You can set ALARM RESUME as ON to enable the speed dome to resume its previous activity
after the triggered actions finished.
If the speed dome is moving when a linkage action is triggered, it will stop at the current
position and resume from this position after the linkage action is finished.
The speed dome can be configured to resume the PTZ positions, focus, and iris value.

3.5.3 Configuring Auxiliary Alarm Output

Purpose:
An auxiliary alarm output is a configurable alarm output interface on the speed dome back box
which can connect and trigger another alarm device to operate.
Steps:
1. Enter the alarm output configuration submenu:
MAIN MENUS > DOME SETTINGS > AUXS
AUXS
AUX 1 CLOSE
DWELL TIME 2
AUX 2 OPEN
DWELL TIME 0
BACK EXIT
Figure 3-23 Configure the Alarm Output
2. Click IRIS+ to edit the status of the alarm outputs. You can set the auxiliary alarm output type as
OPEN (normally open) and CLOSE (normally closed).
3. Move the cursor to DWELL TIME to set the duration of the alarm output signal. The configurable
rage is 0 to 60 seconds.
4. Link the alarm output to the configured alarm.
Steps:

Manual

View the manual for the Hikvision DS-2AE4215T-A here, for free. This manual comes under the category security cameras and has been rated by 1 people with an average of a 6.8. This manual is available in the following languages: English. Do you have a question about the Hikvision DS-2AE4215T-A or do you need help? Ask your question here

Need help?

Do you have a question about the Hikvision and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Hikvision DS-2AE4215T-A specifications

Below you will find the product specifications and the manual specifications of the Hikvision DS-2AE4215T-A.

General
BrandHikvision
ModelDS-2AE4215T-A | DS-2AE4215T-A
Productsecurity camera
LanguageEnglish
FiletypeUser manual (PDF)
Image sensor
Sensor typeCMOS
Number of sensors1
Optical sensor size1/2.8 "
Progressive scanYes
Number of effective pixels (H x V)1920 x 1080 pixels
Video
Maximum resolution1920 x 1080 pixels
Total megapixels2 MP
Analog signal format systemNTSC, PAL
Automatic gain controlYes
Gain control typeAuto/Manual
Back Light Compensation (BLC)Yes
Highlight Compensation (HLC)Yes
Full HDYes
Supported graphics resolutions1920 x 1080 (HD 1080)
Supported video modes1080p
Privacy maskingYes
Camera
Minimum illumination0.001 lx
White balanceATW, Auto, Indoor, Manual, Outdoor
Camera shutter speed1-1/10000 s
53.8 °
31.9 °
60.4 °
Pan range0 - 360 °
Pan speed100 °/sec
Pan preset speed100 °/sec
Tilt angle range5 - 90 °
Tilt speed80 °/sec
Tilt preset speed80 °/sec
Preset programs quantity256
Performance
Wide Dynamic Range (WDR)Yes
Day/night modeYes
Infrared (IR) cut-off filterYes
TypeCCTV security camera
Placement supportedIndoor & outdoor
PTZ controlYes
PTZ modes5 Pattern
Alarm input/outputYes
Connectivity technologyWired
PTZ protocolsPelco-P/D
Number of languages1
Languages supportEnglish
Lens system
Digital zoom16 x
Optical zoom15 x
Number of lenses1
Auto focusYes
FocusMotorized/Manual
Focal length range5 - 75 mm
Detect distance (tele)1.5 m
Detect distance (wide)0.01 m
Maximum aperture number3.5
Minimum aperture number1.6
Power
Power source typeAC
AC input voltage24 V
Power consumption (max)14 W
Operational conditions
Operating temperature (T-T)-30 - 65 °C
Operating relative humidity (H-H)0 - 90 %
Design
International Protection (IP) codeIP66
Form factorDome
Product colorBlack, White
Mounting typeCeiling
Packaging content
Number of cameras1
Weight & dimensions
Diameter180 mm
Height239.5 mm
Weight2000 g
Network
Ethernet LANNo
Wi-FiNo
BluetoothNo
Ports & interfaces
InterfaceBNC
Storage
Built-in HDDNo
Night vision
Night vision-
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Hikvision DS-2AE4215T-A below.

What is the weight of the Hikvision DS-2AE4215T-A?

The Hikvision DS-2AE4215T-A has a weight of 2000 g.

What is a megapixel?

The number of megapixels denotes how many pixels there are in the sensor. 1 megapixel equals 1 million pixels. The more pixels, the higher the potential image quality.

What does the abbreviation 'MP' stand for?

MP stands for MegaPixels.

What is the height of the Hikvision DS-2AE4215T-A?

The Hikvision DS-2AE4215T-A has a height of 239.5 mm.

Is the manual of the Hikvision DS-2AE4215T-A available in English?

Yes, the manual of the Hikvision DS-2AE4215T-A is available in English .

Is your question not listed? Ask your question here

No results