Hikvision DS-2AE4215T-A manual

Hikvision DS-2AE4215T-A
6.8 · 1
PDF manual
 · 48 pages
English
manualHikvision DS-2AE4215T-A
HD-TVI Speed Dome User Manual
33
2. Choose the alarm number.
Steps:
(1) Move the cursor to ALARM NUM and click the IRIS+ to enter the editing mode.
(2) Click the up and down direction buttons to select the number of the alarm which is to be
configured.
(3) Click IRIS+ again to confirm and exit editing mode of this column.
You can configure up to 2 alarm inputs.
3. Move the cursor to ALARM SETTING and click the IRIS+ to enter the setting alarm submenu.
4. Configure the alarm input.
Steps:
(1) Move the cursor to ALARM INPUT and click the IRIS+ to enter the editing mode.
(2) Click the up and down direction buttons to set the input status. You can configure it as OPEN
(Normally open), CLOSE (Normally closed) or OFF (disable the alarm input).
(3) Click IRIS+ again to confirm.
If you set the status as OPEN, alarm will be triggered by high electricity level; if you set the
status as CLOSE, alarm will be triggered by low electricity level; if you set the status as OFF, it
will be triggered when this input channel is shut off.
5. Configure the alarm linkage action.
You can specify the linked action when an alarm occurs.
(1) Move the cursor to ALARM AC and click the IRIS+ to enter the editing mode.
(2) Click the up and down direction buttons to choose the desired linkage action. You can set
the alarm action as preset from 1 to 8, pattern from 1 to 5, patrol from 1 to 10, panning
scan, tilting scan, panoramic scan, day mode, night mode or none. You can also set the
alarm output for the alarm. Refer to Section 3.5.3 Configuring Auxiliary Alarm Output for
details.
6. Configure alarm priority.
Enter the PRIORITY menu and set the alarm priority as HIGH, MIDUEM or LOW.
If multiple alarms with different priorities are triggered at the same time, the dome only
responds to the alarm with the highest priority. If multiple alarms with the same priority are
triggered at the same time, then the dome will respond to each alarm according to the defined
alarm sequence.

3.5.2 Configuring Alarm Parameters

Purpose:
You can set the alarm related parameters following below instructions, including linkage action
interval, alarm duration, and dome activity resumption.
Steps:
1. Enter the alarm parameter configuration menu:
MAIN MENUS > DOME SETTINGS > ALARMS

Manual

View the manual for the Hikvision DS-2AE4215T-A here, for free. This manual comes under the category security cameras and has been rated by 1 people with an average of a 6.8. This manual is available in the following languages: English. Do you have a question about the Hikvision DS-2AE4215T-A or do you need help? Ask your question here

Need help?

Do you have a question about the Hikvision and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Hikvision DS-2AE4215T-A specifications

Below you will find the product specifications and the manual specifications of the Hikvision DS-2AE4215T-A.

General
BrandHikvision
ModelDS-2AE4215T-A | DS-2AE4215T-A
Productsecurity camera
LanguageEnglish
FiletypeUser manual (PDF)
Image sensor
Sensor typeCMOS
Number of sensors1
Optical sensor size1/2.8 "
Progressive scanYes
Number of effective pixels (H x V)1920 x 1080 pixels
Video
Maximum resolution1920 x 1080 pixels
Total megapixels2 MP
Analog signal format systemNTSC, PAL
Automatic gain controlYes
Gain control typeAuto/Manual
Back Light Compensation (BLC)Yes
Highlight Compensation (HLC)Yes
Full HDYes
Supported graphics resolutions1920 x 1080 (HD 1080)
Supported video modes1080p
Privacy maskingYes
Camera
Minimum illumination0.001 lx
White balanceATW, Auto, Indoor, Manual, Outdoor
Camera shutter speed1-1/10000 s
53.8 °
31.9 °
60.4 °
Pan range0 - 360 °
Pan speed100 °/sec
Pan preset speed100 °/sec
Tilt angle range5 - 90 °
Tilt speed80 °/sec
Tilt preset speed80 °/sec
Preset programs quantity256
Performance
Wide Dynamic Range (WDR)Yes
Day/night modeYes
Infrared (IR) cut-off filterYes
TypeCCTV security camera
Placement supportedIndoor & outdoor
PTZ controlYes
PTZ modes5 Pattern
Alarm input/outputYes
Connectivity technologyWired
PTZ protocolsPelco-P/D
Number of languages1
Languages supportEnglish
Lens system
Digital zoom16 x
Optical zoom15 x
Number of lenses1
Auto focusYes
FocusMotorized/Manual
Focal length range5 - 75 mm
Detect distance (tele)1.5 m
Detect distance (wide)0.01 m
Maximum aperture number3.5
Minimum aperture number1.6
Power
Power source typeAC
AC input voltage24 V
Power consumption (max)14 W
Operational conditions
Operating temperature (T-T)-30 - 65 °C
Operating relative humidity (H-H)0 - 90 %
Design
International Protection (IP) codeIP66
Form factorDome
Product colorBlack, White
Mounting typeCeiling
Packaging content
Number of cameras1
Weight & dimensions
Diameter180 mm
Height239.5 mm
Weight2000 g
Network
Ethernet LANNo
Wi-FiNo
BluetoothNo
Ports & interfaces
InterfaceBNC
Storage
Built-in HDDNo
Night vision
Night vision-
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Hikvision DS-2AE4215T-A below.

What is the weight of the Hikvision DS-2AE4215T-A?

The Hikvision DS-2AE4215T-A has a weight of 2000 g.

What is a megapixel?

The number of megapixels denotes how many pixels there are in the sensor. 1 megapixel equals 1 million pixels. The more pixels, the higher the potential image quality.

What does the abbreviation 'MP' stand for?

MP stands for MegaPixels.

What is the height of the Hikvision DS-2AE4215T-A?

The Hikvision DS-2AE4215T-A has a height of 239.5 mm.

Is the manual of the Hikvision DS-2AE4215T-A available in English?

Yes, the manual of the Hikvision DS-2AE4215T-A is available in English .

Is your question not listed? Ask your question here

No results