Graef Euro 3020 manual

Graef Euro 3020
9.9 · 1
PDF manual
 · 72 pages
English
manualGraef Euro 3020
1 Sicherheit 4
1 Saftey 4
1 Sécurité 4
1 Veiligheid 5
2 Beschreibung, Technische Daten 15
2 Description, technical data 15
2 Description, caractéristiques techniques 15
2 Omschrijving, technische gegevens 15
3 Transportieren, Aufstellen 18
3 Transport, installation 18
3 Transport, installation 18
3 Verplaatsen, plaatsen 18
4 Bedienen 24
4 Operation 24
4 Utilisation 24
4 Het bedienen 24
5 Reinigen 42
5 Cleaning 43
5 Nettoyage 43
5 Schoonmaken 44
6 Wartung 50
6 Servicing 50
6 Entretien 50
6 Servicebeurt 50
7 Messer schärfen 51
7 Sharpening of knife 51
7 Affûtage du couteau 51
7 Het mes slijpe 51
8 Fehler beseitigen 60
8Faultnding 60
8 Elimination de problèmes 60
8 Problem corrigiren 60

Inhalt / Table of content / Sommaire / Inhoud

2

View the manual for the Graef Euro 3020 here, for free. This manual comes under the category cutting machines and has been rated by 1 people with an average of a 9.9. This manual is available in the following languages: English. Do you have a question about the Graef Euro 3020 or do you need help? Ask your question here

Need help?

Do you have a question about the Graef and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

General
BrandGraef
ModelEuro 3020
Productcutting machine
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Graef Euro 3020 below.

How can I troubleshoot if the Graef Euro 3020 cutting machine is not cutting properly?

To troubleshoot if the Graef Euro 3020 cutting machine is not cutting properly, follow these steps: 1. Check the direction of blade rotation: Press the On button to start the machine and observe the direction of the blade rotation. The blade should turn from the top downwards against the product. If the rotation is incorrect, it may cause cutting issues. 2. Remove any burrs on the knife: If a burr has formed on the knife edge, turn the adjusting knob to the honing position. Allow the machine to run for a few revolutions until the burr is removed. This can help improve the cutting performance. 3. Clean the machine and the knife: After removing the knife sharpener (if applicable), fully close the thickness plate. Then, clean the machine and the knife from any grinding dust or debris. This ensures optimal cutting performance and prevents any obstructions. By following these steps, you can troubleshoot and improve the cutting performance of the Graef Euro 3020 cutting machine.

What should I do if the Graef Euro 3020 cutting machine is not turning on?

If the Graef Euro 3020 cutting machine is not turning on, there are a few steps you can take to troubleshoot the issue: 1. Check the power supply: Ensure that the machine is properly plugged into a functioning power outlet. Verify that the local operating voltage matches the specifications on the machine's typeplate. If there are any deviations, do not connect the machine. 2. Inspect the mains fuse: Verify that the mains fuse corresponds to the information provided in chapter 2.2 of the manual. If there are any discrepancies, do not connect the machine. 3. Press the red off switch: In case of an emergency, press the red off switch immediately. This may reset the machine and allow it to turn on. 4. Check for defects and deviations: Prior to the initial operation, inspect the safety equipment according to chapter 1.9 and ensure that the equipment and function of the machine align with chapters 2.1 and 2.2. Any defects or deviations should be addressed before operating the machine. By following these steps, you can troubleshoot the issue of the Graef Euro 3020 cutting machine not turning on.

How can I troubleshoot if the Graef Euro 3020 cutting machine is making unusual noises during operation?

To troubleshoot unusual noises during operation of the Graef Euro 3020 cutting machine, follow these steps: 1. Before starting the machine, check the safety equipment as described in section 1.9 of the manual. 2. Thoroughly clean the machine, including all parts and components, as explained in chapter 6 of the manual. 3. Ensure that the machine is placed on a stable and level surface to prevent any vibrations or instability during operation. 4. Check for any loose or damaged parts, such as blades or screws, and tighten or replace them if necessary. 5. Make sure that the material being cut is properly aligned and positioned on the cutting surface to avoid any obstructions or irregularities that may cause noise. 6. Lubricate the moving parts of the machine, following the instructions provided in the manual, to reduce friction and noise. 7. If the unusual noise persists, turn off the machine immediately by pressing the red off switch, as indicated in section 1.10 of the manual, and contact the manufacturer or a qualified technician for further assistance. By following these steps, you can troubleshoot and address any unusual noises that may occur during the operation of the Graef Euro 3020 cutting machine.

Is the manual of the Graef Euro 3020 available in English?

Yes, the manual of the Graef Euro 3020 is available in English .

Is your question not listed? Ask your question here

No results