Furuno 1954C-BB manual

Furuno 1954C-BB
9.6 · 1
PDF manual
 · 223 pages
English
manualFuruno 1954C-BB
3. PLOTTER OPERATION

3-30

Editing a waypoint from the plotter display
You may edit waypoints from the plotter display as follows:
1. Press the MENU key followed by the C: WAYPOINTS/ROUTES and A: WAYPOINTS
soft key to open the waypoint menu.
2. Press the C: WAYPOINT BY CURSOR soft key.
3. Operate the Trackball to place the cursor on the waypoint which you want to change. A
flashing diamond mark appears on the waypoint when it is correctly selected.
4. Press the D: EDIT/MOVE soft key. Three soft keys replace the D: EDIT/MOVE soft key:
EDIT WPT: Edit from the waypoint entry window.
MOVE WPT: Move waypoint to new position with the cursor.
ERASE WPT: Erase waypoint. See paragraph 3.8.3.
5. Press the appropriate soft key. For the “EDIT WPT,” the waypoint entry window
appears; edit data as appropriate. For “MOVE WPT,” do the following:
a) Operate the Trackball to place the cursor on the location desired for the waypoint. A
line connects previous position and new position.
b) Push the ENTER knob. The waypoint moves to the cursor position and its position is
changed on the waypoint list. If the waypoint is set as destination or is part of a route,
you are asked if you are sure to move the waypoint. In this case, push the ENTER
knob to move the waypoint, or press the CLEAR key to cancel.
6. Press the MENU key to finish.
BRIDGEWP-002 34° 22. 345'N 86.6°
M
TRIP NU080° 22. 345'E 4.53nm 99.9 nmPress to alternately displayrange/bearing from own shipto cursor, range/bearing fromoriginal waypoint position tocursor position.Below is an example of therange/bearing from originalwaypoint position to cursorposition.
FISH
(2) Drag cursor to new position, then push the ENTER knob.(1) Select waypoint to move, then press D: EDIT/MOVE and C: MOVE WPT soft keys. 16.0nm
+
Range and bearing fromown ship to cursor 34° 22. 3456'N FROM 5.3°M080° 22. 3456'E FISH 1.45 nm
+

CANCELE

RNG

BRG

C

Plotter display

3.8.3 Erasing waypoints

Erasing a waypoint directly from the plotter display

1. Operate the Trackball to place the cursor on the waypoint you want to erase. A flashing

diamond mark appears over the waypoint when the waypoint is correctly selected.

2. Press the CLEAR key. You are asked if you are sure to erase the waypoint.
3. Push the ENTER knob. The waypoint is erased from the plotter screen and the waypoint

list.

Manual

View the manual for the Furuno 1954C-BB here, for free. This manual comes under the category marine radars and has been rated by 1 people with an average of a 9.6. This manual is available in the following languages: English. Do you have a question about the Furuno 1954C-BB or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Furuno and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Furuno 1954C-BB specifications

Below you will find the product specifications and the manual specifications of the Furuno 1954C-BB.

General
BrandFuruno
Model1954C-BB
Productmarine radar
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Furuno 1954C-BB below.

Is the manual of the Furuno 1954C-BB available in English?

Yes, the manual of the Furuno 1954C-BB is available in English .

Is your question not listed? Ask your question here

No results