Furuno 1954C-BB manual

Furuno 1954C-BB
9.6 · 1
PDF manual
 · 223 pages
English
manualFuruno 1954C-BB
3. PLOTTER OPERATION

3-40

Navigating to a single quick point
1. Place the cursor on an existing waypoint (D: GOTO WPT soft key appears) or a new
location (D: GOTO CURSOR soft key appears).
2. Select “1 POINT” following the procedure in the above paragraph.
3. Depending on the selection you made at step 1, press the D: GOTO CURSOR or D:
GOTO WPT soft key.
A solid blue line with arrows connects between own ship and destination, which is marked
as “<QP01>” for cursor-selected location or waypoint name in case of waypoint. This line
shows the shortest course to the destination. Arrows on the line show the direction to follow
to get to the quick point. Range and bearing from own ship to the destination appear at the
top of screen. The quick point location is saved to the waypoint list as waypoint “QP01.”
Navigating to multiple quick points
1. Select “35 POINTS” following the procedure in “Selecting quick point entry method” on
the previous page.
2. Press the D: GOTO soft key.
3. Place the cursor on an existing waypoint (C: SELECT WPT soft key appears) or a new
location (C: ADD QP soft key appears).
4. Depending on the action taken at step 3, press the C: SELECT WPT or C: ADD QP soft
key. “QP<01>” appears at the cursor location if a quick point is selected. To erase
last-entered quick point (waypoint), press the D: ERASE LST QP (D: ERASE LST WP)
soft key.
5. Repeat steps 3 and 4 to complete the route.
6. Push the ENTER knob to finish.
A solid light-blue line with arrows connects between own ship and the first point and all
other points are connected with a green dashed line with arrows. Arrows on the line show
the direction to follow to get to your destination. Quick points are numbered in sequential
order from QP<01> and are saved to the waypoint list. Range and bearing from own ship to
the first destination appear at the top of screen. The quick points are saved as a route,
under the name “Q>RTE” (Quick Route).

3.10.2 Navigating to waypoints

Selecting a waypoint from the plotter display
1. Operate the Trackball to select a waypoint.
2. Press the D: GOTO WPT soft key.
Note: GOTO method should be selected to “1 POINT” on the PLOTTER SETUP menu.
Selecting a waypoint from the waypoint list
1. Press the MENU key to open the menu.
2. Press the C: WAYPOINTS/ROUTES soft key.
3. Press the A: WAYPOINTS soft key to open the waypoint menu.
4. Press the A: LOCAL LIST or B: ALPHANUMERIC LIST soft key as desired.
5. Use the Trackball to select a waypoint.

Manual

View the manual for the Furuno 1954C-BB here, for free. This manual comes under the category marine radars and has been rated by 1 people with an average of a 9.6. This manual is available in the following languages: English. Do you have a question about the Furuno 1954C-BB or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Furuno and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Furuno 1954C-BB specifications

Below you will find the product specifications and the manual specifications of the Furuno 1954C-BB.

General
BrandFuruno
Model1954C-BB
Productmarine radar
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Furuno 1954C-BB below.

Is the manual of the Furuno 1954C-BB available in English?

Yes, the manual of the Furuno 1954C-BB is available in English .

Is your question not listed? Ask your question here

No results