Fujitsu TFM Module f/FBU option manual

Fujitsu TFM Module f/FBU option
9 · 1
PDF manual
 · 116 pages
English
manualFujitsu TFM Module f/FBU option
76
Modular RAID Controllers
Modular RAID 12Gb/s (SAS3.0)

5.1.1 Features

The RAID controller "PRAID EP400i / EP420i" implements the LSI SAS3108
which is an integrated SAS and I/O controller with dual embedded Power PC
476 cores running at speeds up to 1.2 GHz. The LSI SAS3108 also provides the
following functionalities:
Provides an 8-lane 5.0 / 8.0 Gbit PCIe 3.0 host bus.
Provides an 8-port 12Gb/s SAS3 and 6Gb/s SATA3 interface.
Provides a 1866-MHz DDR3 SDRAM interface with a hardware RAID assist
engine for parity calculations.
Provides a full-featured hardware-based RAID solution that supports RAID
levels 0, 1, 1E, 5, 6, 10, 50, and 60.
Six I
2
C interfaces used for Serial Boot strap ROM connection, memory
detection, PCI-E SMBus connectivity, battery / smart charger control, and
SAS sideband control.
Integrated dual UART for MegaRAID
®
diagnostic use only.
Two banks of SGPIO signals to accompany the two sets of x4 SAS / SATA
ports.
16MB Flash
1kB Bootstrap EEPROM
Mounting holes for TFM
Raid-key chip onboard

5.1.2 Controller versions

Name Chip PCIe Cache
No. of SAS
channels
Bracket
type
PRAID EP400i
S26361-
D3216-Axx
LSI SAS3108 PCIe 3.0 1 GB 8
low profile
full height
PRAID EP420i
S26361-
D3216-Bxx
LSI SAS3108 PCIe 3.0 2 GB 8
low profile
full height

Manual

View the manual for the Fujitsu TFM Module f/FBU option here, for free. This manual comes under the category controllers and has been rated by 1 people with an average of a 9. This manual is available in the following languages: English. Do you have a question about the Fujitsu TFM Module f/FBU option or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Fujitsu and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Fujitsu TFM Module f/FBU option specifications

Below you will find the product specifications and the manual specifications of the Fujitsu TFM Module f/FBU option.

General
BrandFujitsu
ModelTFM Module f/FBU option | S26361-F3669-L100
Productcontroller
EAN4051554398217, 4053162300125, 5053866578300
LanguageEnglish
FiletypeUser manual (PDF)
Ports & interfaces
PCI Express slots version2.0
Host interfacePCI Express
Supported storage drive interfacesSerial ATA
Performance
RAID levels0, 1,5, 6
SSD supportYes
Data transfer rate6 Gbit/s
Internal memory1000 MB
Memory clock speed1333 MHz
Compatible productsD3116
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Fujitsu TFM Module f/FBU option below.

A battery in my controller has started to corrode. Is the device still safe to use?

The product can still be used safely after proper cleaning. Remove the battery with gloves and clean the battery compartment with a toothbrush and vinegar. After drying, new batteries can be inserted into the device.

Does the Fujitsu TFM Module f/FBU option support SSDs?

Yes, the Fujitsu TFM Module f/FBU option supports SSDs, allowing for faster data transfer rates and improved performance for the user compared to traditional HDDs.

What is the data transfer rate of the Fujitsu TFM Module f/FBU option?

The data transfer rate of the Fujitsu TFM Module f/FBU option is 6 Gbit/s, which is quite high and ensures quick access to and retrieval of data for the user.

What types of RAID levels are supported by the Fujitsu TFM Module f/FBU option?

The Fujitsu TFM Module f/FBU option supports RAID levels 0, 1, 5, and 6, providing users with a range of options for data redundancy and performance optimization.

How much internal memory does the Fujitsu TFM Module f/FBU option have?

The Fujitsu TFM Module f/FBU option has 1000 MB of internal memory, which is sufficient for handling storage operations effectively and efficiently.

What is the host interface of the Fujitsu TFM Module f/FBU option?

The host interface of the Fujitsu TFM Module f/FBU option is PCI Express, which is a commonly used and reliable interface for connecting the module to the motherboard and other components in the system.

How should the FBU be mounted inside the chassis during installation?

To mount the FBU inside the chassis during installation of the Fujitsu TFM Module f/FBU option controller, follow these steps: 1. Fit the FBU under both retaining brackets of the FBU holder at a slight angle. 2. Push the FBU in until it locks in place. 3. Connect the cable end of the FBU cable to the FBU adapter cable. 4. Secure the FBU to the server chassis according to the server documentation. 5. Connect the loose end of the FBU adapter cable to the TFM on the RAID controller. These steps ensure proper installation of the FBU within the chassis.

What steps are involved in connecting the FBU to the TFM on the RAID controller using the supplied cables?

To connect the Fujitsu TFM Module f/FBU option to the RAID controller using the supplied cables, follow these steps: 1. Connect the cable end of the FBU cable to the FBU adapter cable. 2. Secure the FBU to the server chassis according to the server documentation. 3. Connect the loose end of the FBU adapter cable to the TFM on the RAID controller. Ensure proper connection as shown in the manual for seamless integration.

Is the manual of the Fujitsu TFM Module f/FBU option available in English?

Yes, the manual of the Fujitsu TFM Module f/FBU option is available in English .

Is your question not listed? Ask your question here

No results