Focusrite Scarlett 6i6 manual

Focusrite Scarlett 6i6
9.6 · 2
PDF manual
 · 34 pages
English
manualFocusrite Scarlett 6i6
33

Scarlett 6i6 Performance Specifications

Configuration
Inputs 6: analogue (4), S/PDIF (2)
Outputs 6: analogue (4), S/PDIF (2)
Mixer Fully assignable 6-in/6-out
Digital Performance
A-D Dynamic Range 104 dB CCIR-RMS (all inputs)
D-A Dynamic Range 102 dB CCIR-RMS (line outputs)
Supported sample rates 44.1 kHz, 48 kHz, 88.2 kHz & 96 kHz
Clock jitter
<250 ps
Microphone Inputs
Frequency Response ±0.5 dB @ 20 Hz, ±0.1 dB @ 20 kHz; min gain
THD+N -96 dB (1 kHz, –1dBFS, 20 kHz BW)
Noise EIN
–122 dBu CCIR-RMS (measured at 60 dB of gain with
150 ohm termination)
Maximum input level +9 dBu (without pad)
Line Inputs
Frequency Response ±0.5dB @ 20 Hz , ±0.1 dB @ 20 kHz (min. gain)
THD+N -80 dB (1 kHz, –1dBFS, 20 kHz BW)
Noise –105 dBFS CCIR-RMS (min. gain, 150 ohm termination)
Maximum input level +28 dBu
Instrument Inputs
Frequency Response ± 0.3 dB @ 20 Hz, ± 0.1 dB @ 20 kHz (min. gain)
Noise –103 dBFS CCIR-RMS (measured at min. gain)
Maximum input level +8 dB (without pad)
Line Outputs
Maximum Output Level (0 dBFS) +11 dBu, balanced
THD+N -100 dB (1 kHz, -1dBFS, 20 kHz BW)

Manual

View the manual for the Focusrite Scarlett 6i6 here, for free. This manual comes under the category hi-fi systems and has been rated by 2 people with an average of a 9.6. This manual is available in the following languages: English. Do you have a question about the Focusrite Scarlett 6i6 or do you need help? Ask your question here

Need help?

Do you have a question about the Focusrite and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Focusrite Scarlett 6i6 specifications

Below you will find the product specifications and the manual specifications of the Focusrite Scarlett 6i6.

General
BrandFocusrite
ModelScarlett 6i6 | SCARLETT 6I6
Producthi-fi system
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Focusrite Scarlett 6i6 below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is HDMI?

HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my hi-fi system?

A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

How do I troubleshoot if I cannot hear any sound from the Scarlett 6i6 hi-fi system when using the example configuration?

To troubleshoot if you cannot hear any sound from the Scarlett 6i6 hi-fi system when using the example configuration, follow these steps: 1. Check the connections: Ensure that the Scarlett 6i6 is properly connected to your computer or audio device. Verify that the input sources, such as microphones and instruments, are correctly plugged into the appropriate input sockets on the front panel of the Scarlett 6i6. 2. Verify the input settings: In Scarlett MixControl software, check the input settings to ensure that the correct input sources are selected and properly configured. Make sure that the input channels corresponding to the connected microphones and instruments are enabled and set to the appropriate level. 3. Check the output settings: Confirm that the output settings in Scarlett MixControl are correctly configured. Ensure that the output channels are enabled and set to an appropriate level. Also, check if the output is routed to the desired playback device, such as speakers or headphones. 4. Test different monitoring options: Try monitoring the playback from the DAW through different output options, such as headphones or different pairs of loudspeakers. This can help identify if the issue is specific to a particular output or monitoring device. 5. Restart the system: Sometimes, a simple restart of your computer or audio device can resolve any temporary software or hardware issues. Restart your system and check if the sound is now audible. By following these troubleshooting steps, you should be able to identify and resolve the issue of not hearing any sound from the Scarlett 6i6 hi-fi system when using the example configuration.

Why is there no audio input signal when connecting a microphone or instrument to the Scarlett 6i6 hi-fi system?

To troubleshoot the issue of no audio input signal when connecting a microphone or instrument to the Scarlett 6i6 hi-fi system, follow these steps: 1. Check the connections: Ensure that the microphone or instrument is properly connected to the appropriate input sockets on the front panel of the Scarlett 6i6. Use an XLR cable for microphones or a ¼” (6.35 mm) jack plug for instruments. 2. Verify the input settings: Open the Scarlett MixControl software and check the input settings. Make sure that the input channels corresponding to the connected microphone or instrument are enabled and properly configured. Adjust the input gain controls (GAIN 01 and GAIN 02) to an appropriate level. 3. Select the correct input type: In Scarlett MixControl, select the input configuration that matches the connected device. Choose "INST" if you are connecting a musical instrument via a 2-pole guitar jack, or select "LINE" for a line-level source like the balanced output of an external audio mixer. 4. Check the pad settings: If the input signal is too strong, enable the 10 dB pad for the respective input channel in Scarlett MixControl. This will increase the headroom and prevent distortion. Note that the pad should not be used with instrument inputs. 5. Test with different microphones or instruments: If the issue persists, try connecting different microphones or instruments to the Scarlett 6i6 to determine if the problem lies with the specific device being used. By following these troubleshooting steps, you should be able to identify and resolve the issue of no audio input signal when connecting a microphone or instrument to the Scarlett 6i6 hi-fi system.

How can I fix latency issues when monitoring the playback from the DAW using the Scarlett 6i6 hi-fi system?

To fix latency issues when monitoring the playback from the DAW using the Scarlett 6i6 hi-fi system, follow these steps: 1. Understand latency: Latency refers to the delay between when you play or sing a sound and when you hear it through your headphones or speakers. In digital audio systems, this delay is caused by the time it takes for the audio signals to pass through your computer and audio software. 2. Enable low latency monitoring: The Scarlett 6i6, in conjunction with Scarlett MixControl software, allows for low latency monitoring. This means you can route your input signals directly to the Scarlett 6i6's headphone and line outputs, bypassing the computer's processing. This enables you to hear yourself in real-time along with the computer playback. 3. Configure the buffer size: In Scarlett MixControl, you can adjust the buffer size of your ASIO driver. A smaller buffer size will result in lower latency but may increase CPU usage. If you are experiencing high CPU usage, you can increase the buffer size to reduce latency. 4. Avoid input-to-output routing in your DAW: When using direct monitoring, ensure that your DAW software is not set to route any inputs (what you are currently recording) to any outputs. This can cause a delay and result in hearing yourself twice. By following these steps, you can effectively address latency issues when monitoring the playback from the DAW using the Scarlett 6i6 hi-fi system.

What should I do if I cannot hear myself with low latency during direct monitoring with the Scarlett 6i6 hi-fi system?

To fix the issue of not being able to hear yourself with low latency during direct monitoring with the Scarlett 6i6 hi-fi system, follow these steps: 1. Understand latency: Latency refers to the delay between when you play or sing a sound and when you hear it through your headphones or speakers. In digital audio systems, this delay is caused by the time it takes for the audio signals to pass through your computer and audio software. 2. Enable low latency monitoring: The Scarlett 6i6, in conjunction with Scarlett MixControl software, allows for low latency monitoring. This means you can route your input signals directly to the Scarlett 6i6's headphone and line outputs, bypassing the computer's processing. This enables you to hear yourself in real-time along with the computer playback. 3. Check DAW software settings: Ensure that your DAW software is not set to route any inputs (what you are currently recording) to any outputs. If it is, you may hear yourself "twice" with a delayed echo. Adjust the settings to prevent this. By following these steps, you should be able to hear yourself with low latency during direct monitoring with the Scarlett 6i6 hi-fi system.

How do I troubleshoot if the Scarlett 6i6 hi-fi system is not recognized or not working properly in the MixControl software?

To troubleshoot if the Scarlett 6i6 hi-fi system is not recognized or not working properly in the MixControl software, follow these steps: 1. Install Scarlett MixControl: Ensure that you have installed the Scarlett MixControl software on your computer before connecting the Scarlett 6i6. You can download the software from the Focusrite website using the validation codes provided with your Scarlett 6i6. 2. Connect the Scarlett 6i6: After installing the software, connect the Scarlett 6i6 to your computer using the USB cable provided. Make sure to power the Scarlett 6i6 using the supplied mains adaptor. 3. Launch Scarlett MixControl: Open the Scarlett MixControl software by going to Start > Programs > Focusrite > Scarlett MixControl on a Windows PC, or Finder > Applications > Scarlett MixControl on a Mac. 4. Check device recognition: Once Scarlett MixControl is open, verify if the software recognizes the Scarlett 6i6. It should automatically detect the model of the interface and configure the software accordingly. 5. Troubleshoot connection issues: If the Scarlett 6i6 is not recognized, ensure that the USB cable is securely connected and try using a different USB port on your computer. Restart your computer if necessary. By following these steps, you should be able to troubleshoot and resolve any issues with the Scarlett 6i6 not being recognized or not working properly in the MixControl software.

Is the manual of the Focusrite Scarlett 6i6 available in English?

Yes, the manual of the Focusrite Scarlett 6i6 is available in English .

Is your question not listed? Ask your question here

No results