View the manual for the Fluid Apollo Plus here, for free. This manual comes under the category rowing machines and has been rated by 1 people with an average of a 9. This manual is available in the following languages: English. Do you have a question about the Fluid Apollo Plus or do you need help? Ask your question here
| Brand | Fluid |
| Model | Apollo Plus |
| Product | rowing machine |
| Language | English |
| Filetype | User manual (PDF) |
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Fluid Apollo Plus below.
As an adult, it is recommended to do moderately intensive exercise for at least 2.5 hours per week. Preferably spread over several days.
As a rule of thumb for your maximum heart rate, you can use 220 minus your age.
To adjust the Fluid Resistance Technology on the Fluid Apollo Plus rowing machine, follow these steps: 1. Start by selecting your preferred Fluid Resistance level on the rowing machine. You can adjust the resistance using the UP and DOWN buttons on the monitor. 2. When adjusting the resistance level, allow two strokes to feel an increase in resistance and ten strokes to feel a decrease. 3. To remove or change the water in the tank, follow these steps: a) Set the Adjuster Knob to "1". b) Row at least ten strokes to fill the storage reservoir as completely as possible. c) Remove the Tank Plug. d) Insert the rigid end of the siphon into the tank and the flexible hose into a large bucket. e) Drain approximately 40% of the water from the tank. Some water will remain. f) Refill the tank following the directions for tank filling as described in the manual. Note: It is important to use the water treatment tablets supplied with the rowing machine for proper maintenance. Contact your local First Degree Fitness distributor for replacement tablets. By following these steps, you can easily adjust the Fluid Resistance Technology on the Fluid Apollo Plus rowing machine.
The International Warranty for the Fluid Apollo Plus rowing machine (model APWP / APWPBL) covers the following: 1. Main Frame - 5 Year Limited Warranty: FIRST DEGREE FITNESS will repair or replace the Metal Main Frame of the rower if it fails due to any defect in materials or workmanship within 5 years of the original purchase. Please note that the warranty does not apply to frame coating. 2. Polycarbonate Tank & Seals - 5 Year Limited Warranty: FIRST DEGREE FITNESS will repair or replace the polycarbonate Tank or seals if they fail due to any defect in materials or workmanship within 5 years of the original purchase. 3. Mechanical Components (of a non-wearing nature) - 2 Year Limited Warranty: FIRST DEGREE FITNESS will repair or replace any mechanical component if it fails due to any defect in materials or workmanship within 2 years of the original purchase. This includes the Seat Frame, Seat Rails, and Shaft and Impeller Assembly. 4. All Other Components (of a wearing nature) - 1 Year Limited Warranty: FIRST DEGREE FITNESS will repair or replace any component if it fails due to any defect in materials or workmanship within 1 year of the original purchase. This includes the Bungee Recoil Cord, Hand Grips & Footstraps, Polyester Rowing Belt, Seat and Seat Runners, Pulleys, Rollers & Bearings, and all rubber components. Please note that the warranty does not cover damage to the finish of any part of the machine, damage due to neglect, abuse, incorrect assembly, or use of the machine, charges for freight or customs clearance, damage or loss of goods during transport, or any labor costs associated with a warranty claim. The warranty is valid only for the original purchaser and is not transferable. For warranty claims, the serial number of the machine must be correctly registered with FIRST DEGREE FITNESS or one of its appointed distributors. The product must be returned to the place of purchase in its original packaging, with transportation, insurance, and associated charges paid for by the customer. Please refer to the manual for more detailed information on the International Warranty for the Fluid Apollo Plus rowing machine.
To troubleshoot issues with the metal main frame of the Fluid Apollo Plus rowing machine, follow these steps: 1. Check for any visible damage or signs of wear on the metal main frame. Look for cracks, dents, or loose connections. 2. Ensure that all bolts and nuts securing the main frame are tightened properly. Use the provided tools to tighten any loose connections. 3. If there is excessive noise or vibration coming from the main frame during use, check if any components are loose or misaligned. Tighten or adjust them as necessary. 4. If the main frame is not stable or wobbles during rowing, make sure that the rowing machine is placed on a level surface. Adjust the leveling feet if needed. 5. If you encounter any major issues with the metal main frame, such as structural damage or failure, contact the nearest First Degree Fitness customer service center for further assistance. By following these troubleshooting steps, you can address common issues related to the metal main frame of the Fluid Apollo Plus rowing machine.
The polycarbonate tank and seals of the Fluid Apollo Plus rowing machine (model APWP / APWPBL) are covered under a 5 Year Limited Warranty. This warranty ensures that FIRST DEGREE FITNESS will repair or replace the polycarbonate tank or seals if they fail due to any defect in materials or workmanship within 5 years of the original purchase. It is important to note that the warranty coverage is subject to certain conditions. The warranty does not cover damage caused by neglect, abuse, incorrect assembly, or use of the rowing machine. Additionally, charges for freight or customs clearance, damage or loss of goods during transport, and any labor costs associated with a warranty claim are not covered. To make a warranty claim for the polycarbonate tank or seals, ensure that the serial number of the rowing machine is correctly registered with FIRST DEGREE FITNESS or one of its appointed distributors. The product must be returned to the place of purchase in its original packaging, with transportation, insurance, and associated charges paid for by the customer. For more detailed information on the warranty coverage for the polycarbonate tank and seals of the Fluid Apollo Plus rowing machine, please refer to the manual.
To troubleshoot mechanical component issues that are not subject to wear on the Fluid Apollo Plus rowing machine, follow these steps: 1. If the water in the tank changes color or becomes cloudy, it may be due to direct sunlight exposure or poor-quality tap water. Move the rowing machine to reduce direct sunlight exposure and consider using distilled water or water treatment tablets as directed in the manual. 2. If the rower belt slips off the belt/bungee pulley or the recoil is not strong enough, check if the bungee is under enough tension. Tighten the bungee cord following the instructions in the "Reattaching the Rower Belt" section of the manual. 3. If you experience inconsistent readings on the rower monitor for 500-meter split time and strokes per minute (SPM), it could be due to a faulty sensor, sensor misalignment, or wiring harness issues. Use the battery cover of the monitor as a "gap tool" to check the gap between the sensor head and magnetic ring or contact your nearest FDF customer service center for assistance. 4. If the rower monitor does not illuminate after battery installation, ensure that the batteries are correctly installed and try rotating them slightly. If the issue persists, contact your local service center. 5. If the rower monitor screen illuminates but does not register when rowing, check for loose or failed connections and ensure that the sensor gap is not too wide. If the connections are secure and the issue persists, contact your local service center. By following these troubleshooting steps, you can address common mechanical component issues that are not subject to wear on the Fluid Apollo Plus rowing machine.
Yes, the manual of the Fluid Apollo Plus is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Fluid and is the answer not in the manual?
Question and answer
Number of questions: 0