FireAngel WTSL-F-1EU manual

FireAngel WTSL-F-1EU
8.7 · 1
PDF manual
 · 92 pages
English
manualFireAngel WTSL-F-1EU
22
Battery operated alarm control unit for testing, mute and localization. Hereby, Sprue Safety Products Ltd, declares that this
WTSL-F-1EU is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The
declaration of conformity may be consulted at http://spru.es/WTSL-1EU
Batteriebetriebenes Controller Modul zum Testen, Stummschalten und Lokalisieren. Sprue Safety Products Ltd
erklärt hiermit, dass der WTSL-F-1EU in Übereinstimmung mit den wesentlichen Anforderungen und anderer
relevanter Vorschriften der Directive 2014/53/EU ist. Die Konformitätserklärung kann hier angefragt werden
http://spru.es/WTSL-1EU
Bloc de contrôle d’alarme : Test, Silence, Localisation alimenté par pile. Par la présente déclaration, Sprue Safety Products
conrme que le WTSL-F-1EU est en conformité avec les exigences essentielles et aux autres dispositions pertinentes de la
Directive 2014/53/EU. La déclaration de conformité peut être consultée au http://spru.es/WTSL-1EU
Test, pauze en locatieschakelaar, batterij gevoed. Hierbij verklaard Sprue Safety Products Ltd, dat de WTSL-F-1EU
in overeenstemming is met de essentiele eisen en andere relevante bepalingen van Richtlijn 2014/53/EU.
De verklaring van overeenstemming CE (declaration of conformity) kan worden geraadpleegd op
http://spru.es/WTSL-1EU.
WTSL-F-1EU
GN3244 / R6
Sprue Safety Products Ltd.
Vanguard Centre, Sir William Lyons Road, Coventry CV4 7EZ UK, www.fireangel.eu
A Sprue Brand
Independently tested to RF standard / Unabhängig getested nach / Testé indépendamment pour / Onafhankelijk getest door:
EN 301 489-1 V1.9.2 / EN 301 489-3 V1.6.1 / EN 300 220-2 V3.1.1
Fréquence: 868MHz

Manual

View the manual for the FireAngel WTSL-F-1EU here, for free. This manual comes under the category remote controllers and has been rated by 1 people with an average of a 8.7. This manual is available in the following languages: English. Do you have a question about the FireAngel WTSL-F-1EU or do you need help? Ask your question here

Need help?

Do you have a question about the FireAngel and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

FireAngel WTSL-F-1EU specifications

Below you will find the product specifications and the manual specifications of the FireAngel WTSL-F-1EU.

General
BrandFireAngel
ModelWTSL-F-1EU
Productremote controller
LanguageEnglish
FiletypeUser manual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the FireAngel WTSL-F-1EU below.

A battery in my remote controller has started to corrode. Is the device still safe to use?

The product can still be used safely after proper cleaning. Remove the battery with gloves and clean the battery compartment with a toothbrush and vinegar. After drying, new batteries can be inserted into the device.

How do I activate the wireless interlink feature on the FireAngel WTSL-F-1EU remote controller?

To activate the wireless interlink feature on the FireAngel WTSL-F-1EU remote controller, follow these steps: 1. Ensure that the FireAngel WTSL-F-1EU remote controller is within the Wi-Safe 2 range and compatible with other Wi-Safe 2 devices. 2. Press and hold the interlink button on the remote controller for a few seconds until the LED indicator starts flashing. 3. Release the interlink button and wait for the LED indicator to stop flashing and remain solid. 4. The FireAngel WTSL-F-1EU remote controller is now activated and ready to communicate with other Wi-Safe 2 devices within the network. 5. Test the wireless interlink by triggering an alarm on one device, such as a smoke detector, and check if the remote controller receives the signal and responds accordingly. 6. If the wireless interlink is not functioning properly, ensure that all devices are properly installed, powered on, and within the specified range. 7. If the issue persists, refer to the troubleshooting section of the manual or contact FireAngel customer support for further assistance. Please note that these steps are specific to the FireAngel WTSL-F-1EU remote controller and may vary for other models or brands.

What should I do if the FireAngel WTSL-F-1EU remote controller is not responding to my commands?

If the FireAngel WTSL-F-1EU remote controller is not responding to your commands, you can try the following troubleshooting steps: 1. Check if the remote controller has been successfully activated. If not, refer to the "Activating the Alarm Control Unit" section in the manual for instructions on how to activate it properly. 2. Ensure that the batteries in the remote controller are properly installed and have sufficient power. Replace the batteries if necessary. 3. Make sure that the remote controller is within the specified range of the devices it is supposed to control. Move closer to the devices and try again. 4. Check if there are any obstructions between the remote controller and the devices. Remove any obstacles that may be blocking the signal. 5. If the remote controller is still not responding, try resetting it by removing the batteries and waiting for a few minutes before reinserting them. 6. If none of the above steps resolve the issue, please contact FireAngel Technical Support for further assistance. You can reach them via email at technicalsupport@fireangel.co.uk or by calling 0800 171 2009. Please note that these troubleshooting steps are specific to the FireAngel WTSL-F-1EU remote controller and may not apply to other models or brands.

How do I properly position the FireAngel WTSL-F-1EU remote controller for optimal performance?

To properly position the FireAngel WTSL-F-1EU remote controller for optimal performance, follow these steps: 1. Choose a central location within your home or building to place the remote controller. This will ensure that it can communicate effectively with all the devices it is intended to control. 2. Avoid placing the remote controller near large metal objects or appliances that may interfere with the wireless signal. Keep it away from sources of electromagnetic interference, such as microwaves or cordless phones. 3. Position the remote controller at a height of approximately 1.5 meters (5 feet) from the ground. This will help ensure that it is within reach and easily accessible. 4. Make sure that there are no obstructions between the remote controller and the devices it needs to control. Remove any objects or furniture that may block the signal. 5. If you have multiple floors in your home or building, consider placing additional remote controllers on each floor to ensure optimal coverage and control. By following these steps, you can position the FireAngel WTSL-F-1EU remote controller in a way that maximizes its performance and allows for seamless communication with the devices in your network.

What steps should I follow to install the FireAngel WTSL-F-1EU remote controller?

To install the FireAngel WTSL-F-1EU remote controller, follow these steps: 1. Begin by removing the two cover plates located at the top right of the controller's support using a small screwdriver. Take care to hold the support securely during this step. 2. Once the cover plates are removed, proceed with the rest of the installation. Attach the control unit to its support, ensuring it is securely fixed in place. 3. To remove the control unit from its support, insert a small screwdriver into the hole at the top right corner of the unit until it stops. This will disengage the locking mechanism. 4. After disengaging the lock, gently lift the control unit slightly upward to release it from the support. These steps will guide you through the installation process of the FireAngel WTSL-F-1EU remote controller. Please note that these instructions are specific to this model and may differ for other products.

How can I test the alarm system using the FireAngel WTSL-F-1EU remote controller?

To test the alarm system using the FireAngel WTSL-F-1EU remote controller, follow these steps: 1. Locate the Test/Silence button on the remote controller. It is usually labeled with the word "Test" or an icon representing a test button. 2. Press the Test/Silence button once to initiate the test. This will activate a three-minute test period. 3. During the test, all networked alarms should sound to indicate that the system is functioning properly. Listen for the alarms to ensure they are audible and functioning correctly. 4. If you need to stop the test before the three-minute period is over, simply press the Test/Silence button again. 5. It is recommended to perform this test on a weekly basis to ensure the alarm system is in proper working condition. Please note that pressing the Test button on the FireAngel WTSL-F-1EU remote controller may generate RF traffic. If you need to use this feature multiple times, it is advisable to wait for 5 minutes to allow the network to settle down. These steps will help you test the alarm system using the FireAngel WTSL-F-1EU remote controller.

Is the manual of the FireAngel WTSL-F-1EU available in English?

Yes, the manual of the FireAngel WTSL-F-1EU is available in English .

Is your question not listed? Ask your question here

No results