View the manual for the Filex SB 3 here, for free. This manual comes under the category safes and has been rated by 1 people with an average of a 6.3. This manual is available in the following languages: English. Do you have a question about the Filex SB 3 or do you need help? Ask your question here
Below you will find the product specifications and the manual specifications of the Filex SB 3.
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Filex SB 3 below.
To troubleshoot if the Filex SB 3 safe door does not open or close smoothly, follow these steps: 1. Check the door: Ensure that there are no obstructions blocking the door's movement. Remove any debris or objects that may be preventing the door from opening or closing smoothly. 2. Lubricate the hinges: Apply a small amount of lubricant, such as WD-40, to the hinges of the safe door. This can help reduce friction and improve the smoothness of the door's operation. Be sure to wipe off any excess lubricant. 3. Inspect the locking mechanism: Check if the locking mechanism is properly aligned and functioning correctly. Make sure that the bolts or locking mechanism are not loose or damaged. Tighten any loose bolts or screws if necessary. 4. Test the batteries: If the safe is equipped with an electronic lock, check the batteries. Replace them if they are low or depleted. A weak battery can cause issues with the door's operation. 5. Contact customer support: If the above steps do not resolve the issue, it is recommended to contact the dealer or customer support where you purchased the Filex SB 3 safe. They can provide further assistance and troubleshooting guidance specific to your safe model. By following these steps, you should be able to troubleshoot and resolve any issues with the Filex SB 3 safe door not opening or closing smoothly.
If you encounter difficulties during the installation of the Filex SB 3 safe, follow these steps: 1. Place the Filex SB 3 safe in the desired position. 2. Check if the door opens and closes smoothly without any obstructions. 3. Mark the drill points on the floor and/or wall through the pre-drilled holes of the safe. 4. Remove the Filex SB 3 safe and drill 8 mm fixing holes at the marked points. 5. Clean any dust or debris from the fixing holes. 6. Place the Filex SB 3 safe back in position and insert the fixing bolts. 7. Tighten the fixing bolts securely to anchor the safe to the floor and/or wall. By following these steps, you should be able to overcome any difficulties you may encounter during the installation of the Filex SB 3 safe.
To troubleshoot if the Filex SB 3 safe is not securely fixed to the floor and/or wall, follow these steps: 1. Ensure that the safe is placed in the desired position. 2. Check if the door of the safe opens and closes smoothly without any obstructions. 3. Mark the drill points on the floor and/or wall through the pre-drilled holes of the safe. 4. Remove the safe from its position and drill 8 mm fixing holes at the marked points. 5. Clean any dust or debris from the fixing holes to ensure a proper fit. 6. Place the safe back in its position and insert the fixing bolts. 7. Tighten the fixing bolts securely to anchor the safe to the floor and/or wall. By following these steps, you can troubleshoot and ensure that the Filex SB 3 safe is securely fixed to the floor and/or wall.
If any of the components of the Filex SB 3 safe are missing or not functioning properly, follow these steps: 1. Check the components: Verify if all the components listed in the manual are present. These may include the reset button, battery compartment, bolts, lock, green light (OK), yellow light (J), red light, confirmation button, and emergency lock cover. 2. Contact customer support: If any components are missing or not functioning properly, it is recommended to contact the dealer or customer support where you purchased the Filex SB 3 safe. They can provide assistance in obtaining the missing components or troubleshooting any issues with the existing components. By following these steps, you can address any concerns regarding missing or malfunctioning components of the Filex SB 3 safe.
To troubleshoot if the lights on the Filex SB 3 safe are not functioning as expected, follow these steps: 1. Check the power source: Ensure that the safe has a reliable power source. If the safe uses batteries, check if they are properly installed and not depleted. Replace the batteries if necessary. 2. Inspect the lights: Examine the lights on the safe, such as the green light (OK), yellow light (J), and red light. Check if any of the lights are dim, flickering, or not illuminating at all. 3. Clean the contacts: If the lights are not functioning properly, clean the contacts of the lights and the corresponding connectors inside the safe. Use a soft cloth or cotton swab to remove any dirt or debris that may be affecting the electrical connection. 4. Reset the safe: If cleaning the contacts does not resolve the issue, try resetting the safe. Locate the reset button, usually located inside the battery compartment or near the control panel. Press and hold the reset button for a few seconds until the lights on the safe flash or reset. 5. Contact customer support: If the lights still do not function as expected after following the above steps, it is recommended to contact the dealer or customer support where you purchased the Filex SB 3 safe. They can provide further assistance and troubleshooting guidance specific to your safe model. By following these steps, you can troubleshoot and address any issues with the lights on the Filex SB 3 safe.
Yes, the manual of the Filex SB 3 is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Filex and is the answer not in the manual?
Question and answer
Number of questions: 0