Ferroli Egea Lt manual

Ferroli Egea Lt
7.5 · 1
PDF manual
 · 168 pages
English
manualFerroli Egea Lt

EGEA 90LT - 120LT

cod. 3541T580 - Rev. 03 - 05/2020
IT
- MANUALE D’USO, INSTALLAZIONE E MANUTENZIONE
ES - MANUAL DE USO, INSTALACIÓN Y MANTENIMIENTO
EN
- USER, INSTALLATION AND MAINTENANCE MANUAL
PT
- MANUAL DE USO, INSTALAÇÃO E MANUTENÇÃO
FR
- MANUEL D’UTILISATION, INSTALLATION ET ENTRETIEN

View the manual for the Ferroli Egea Lt here, for free. This manual comes under the category water heaters & boilers and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Ferroli Egea Lt or do you need help? Ask your question here

Need help?

Do you have a question about the Ferroli and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 1
H
Hymad Mohammed November 1, 2023

Hi I need water heater 150 L v

Hi I need water heater 150 L v
zoom-in
View photo

General
BrandFerroli
ModelEgea Lt
Productwater heater & boiler
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Ferroli Egea Lt below.

What is the ideal room temperature?

Most people find that the ideal room temperature is between 19 and 22 degrees Celsius.

How can I troubleshoot if the Ferroli Egea Lt water heater & boiler is not commissioning properly?

To troubleshoot if the Ferroli Egea Lt water heater & boiler is not commissioning properly, you can follow these steps: 1. Check the power supply: Ensure that the product is actually powered by the mains. Verify that the power cable inside the product is securely connected. Also, check if the fuse on the power board is intact. If not, replace it with a certified time-delay 5 A fuse. 2. Restart the equipment: Disconnect the equipment from the mains and wait for a few minutes before reconnecting it. This can help reset any temporary issues. 3. Verify the heat pump operation: If the water cannot be heated via the heat pump in ECO or AUTOMATIC mode, switch off the equipment and wait for a few hours. Then, switch it on again. If the issue persists, drain approximately 50% of the water from the tank, refill it, and switch the equipment back on in ECO mode. 4. Check the heating element: If the water cannot be heated via the integrated heating element in AUTOMATIC mode, switch off the equipment and check the safety thermostat of the heating element. Reset it if necessary. You can also increase the value of parameter P32 in the installer menu to ensure proper heating. 5. Troubleshoot Wi-Fi connectivity: If you are unable to control the product via the app, check if there is Wi-Fi network coverage where the product is installed. Reconfigure the Wi-Fi connection with the router and ensure that the Wi-Fi symbol on the display is lit up steadily. If these troubleshooting steps do not resolve the issue, it is recommended to contact the manufacturer's technical assistance service, providing them with any error codes displayed on the equipment or app.

What should I do if I am unable to access or edit the operating parameters of the Ferroli Egea Lt water heater & boiler?

To access or edit the operating parameters of the Ferroli Egea Lt water heater & boiler, follow these steps: 1. Unlock the buttons: With the equipment operating, unlock the buttons by pressing and holding the " " and "+" buttons together for 3 seconds. This will allow you to access the parameter menu. 2. Navigate through the parameter list: Once the buttons are unlocked, the display will show the first parameter labeled with the letter "A". Press the "+" button to display its value. Press the "+" button again to move to the next parameter labeled with the letter "B", and so on. Use the "+" and "-" buttons to scroll forward or backward through the parameter list. 3. Enter the editing mode: To edit the operating parameters, the equipment must be in standby mode. Press and hold the " " and "+" buttons together for 3 seconds to access the parameter editing menu. Enter the password when prompted. 4. Modify the parameters: Once in the editing mode, the display will show the first parameter (e.g., P1). Press the "+" button to display its default value. Use the "+" and "-" buttons to change the value within the permissible range for that parameter. Press " " to confirm the new value and move on to the next parameter. Repeat this process for each parameter you want to edit. 5. Save and exit: After editing the desired parameters, press the on/off button to save the changes and exit the editing mode. The equipment will return to standby mode. Please note that the password for accessing and editing the parameters is reserved for qualified personnel. Incorrect parameter settings may result in product issues, and any interventions requested due to incorrect settings may not be covered by the standard warranty.

What troubleshooting steps should I take if there are water leaks in the Ferroli Egea Lt water heater & boiler?

If there are water leaks in the Ferroli Egea Lt water heater & boiler, you can take the following troubleshooting steps: 1. Check the plumbing connections: Inspect the plumbing connections of the water heater & boiler. Ensure that all connections are tight and secure. Look for any signs of water leakage around the connections. 2. Verify the shutoff cock: Check the shutoff cock, which is a valve that controls the water flow to the water heater & boiler. Make sure it is fully closed and not leaking. 3. Examine the safety valve: Inspect the safety valve, which is designed to release excess pressure from the water heater & boiler. Check if the safety valve is functioning properly and not leaking. If necessary, replace the safety valve. 4. Check the condensate drain: Inspect the condensate drain and ensure that it is not clogged or blocked. Clean the drain if needed to allow proper drainage of condensate. 5. Inspect the automatic thermostatic mixing device: If your water heater & boiler is equipped with an automatic thermostatic mixing device, check if it is functioning correctly. Ensure that the device is not leaking and is set to the desired temperature. If the water leaks persist or if you are unsure about any of the troubleshooting steps, it is recommended to contact the manufacturer's technical assistance service for further guidance and support.

How can I troubleshoot if the power board of the Ferroli Egea Lt water heater & boiler is not functioning correctly?

To troubleshoot if the power board of the Ferroli Egea Lt water heater & boiler is not functioning correctly, you can follow these steps: 1. Check the power supply: Ensure that the product is actually powered by the mains. Verify that the power cable inside the product is securely connected. Also, check if the fuse on the power board is intact. If not, replace it with a certified time-delay 5 A fuse. 2. Restart the equipment: Disconnect the equipment from the mains and wait for a few minutes before reconnecting it. This can help reset any temporary issues. 3. Inspect the power board: Remove the bottom cover of the equipment. Check the power board for any visible signs of damage or loose connections. Ensure that all connections are secure. 4. Replace the fuse: If the fuse on the power board is blown, replace it with a new IEC 60127-2/II certified time-delay 5 A fuse. Make sure to use the correct type and rating of the fuse. 5. Reassemble and test: After replacing the fuse or performing any necessary repairs, reassemble the equipment and ensure that it is correctly installed. Power on the equipment and check if the power board is functioning properly. If these troubleshooting steps do not resolve the issue, it is recommended to contact the manufacturer's technical assistance service for further guidance and support.

What should I do if the Wi-Fi card of the Ferroli Egea Lt water heater & boiler is not connecting to the network?

To troubleshoot if the Wi-Fi card of the Ferroli Egea Lt water heater & boiler is not connecting to the network, you can follow these steps: 1. Ensure power and Wi-Fi availability: Make sure that the equipment is powered and that there is Wi-Fi network coverage where the product is installed. 2. Reset the Wi-Fi connection: With the equipment powered on, press and hold the "+" and " " buttons together for 5 seconds. This will initiate the Wi-Fi connection process. 3. Connect to the network: Using the Ferroli app on your smartphone, select the Wi-Fi network you want to connect the equipment to. Enter the password for the network and confirm the connection on the app. 4. Wait for connection: Allow some time for the equipment to establish a connection with the Wi-Fi router. The Wi-Fi symbol on the display should flash rapidly during this process. 5. Verify successful connection: If the connection procedure is successful, you will see the device added in the app. This indicates that the Wi-Fi card of the Ferroli Egea Lt water heater & boiler is now connected to the network. If the troubleshooting steps do not resolve the issue, it is recommended to contact the manufacturer's technical assistance service for further guidance and support.

Is the manual of the Ferroli Egea Lt available in English?

Yes, the manual of the Ferroli Egea Lt is available in English .

Is your question not listed? Ask your question here

No results