Fanvil X2 manual

Fanvil X2
7.7 · 1
PDF manual
 · 72 pages
English
manualFanvil X2
17 / 72

5 Setting Up

In order to get the device ready for making and receiving phone calls, the device must be configured with
correct network configurations and at least one of the lines must be configured with an SIP telephony service.

5.1 Network Configuration

The device relies on IP network connection to provide service. Unlike traditional phone system based on
a circuit switched wire technology, IP devices are connected to each other over the network and exchange
data in packet basis based on the devices’ IP address.
To enable the device, the network parameters must be configured properly first. To configure network
parameters, user should open the network configuration screen through soft-menu [Menu] -> [Settings] ->
[Advanced Settings] -> [Network] -> [Network Settings] from standby screen.
NOTICE! If user saw a Network Disconnected’ icon flashing in the middle of screen, it means the
network cable was not correctly connected to the device’s network port. Please check the cable is
connected correctly to the device and to the network switch, router, or modem.
There are three common IP configuration modes.
Dynamic Host Configuration Protocol (DHCP) This is the automatic configuration mode by getting
network configurations from a DHCP server. Users need not to configure any parameters manually. All
configuration parameters will be getting from DHCP server and applied to the device. This is
recommended for most users.
Static IP Configuration This option allows user to configure each IP parameters manually, including IP
Address, Subnet Mask, Default Gateway, and DNS servers. This is usually used in an office
environment or by power users.
PPPoE This option is often used by users who connect the device to a broadband modem or router. To
establish a PPPoE connection, user should configure username and password provided by the service
provider.
The device is default configured in DHCP mode.

Manual

View the manual for the Fanvil X2 here, for free. This manual comes under the category phones and has been rated by 1 people with an average of a 7.7. This manual is available in the following languages: English. Do you have a question about the Fanvil X2 or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Fanvil and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Fanvil X2 specifications

Below you will find the product specifications and the manual specifications of the Fanvil X2.

General
BrandFanvil
ModelX2 | X2
Productphone
LanguageEnglish
FiletypeUser manual (PDF)
Phone features
Lines quantity2 lines
Call waitingYes
IntercomYes
Caller IDYes
Call forwardingYes
Call transferYes
Call parkYes
Call pick upYes
RedialingYes
Do not disturb functionYes
Answering machineYes
Conference callYes
Phonebook capacity500 entries
Call log entries100
Message-waiting indicator (MWI)Yes
Phonebook sharingYes
Call holdYes
Number of VoIP accounts-
Display
DisplayLCD
Display diagonal2.8 "
Display resolution320 x 240 pixels
TouchscreenNo
Ports & interfaces
Ethernet LAN (RJ-45) ports2
RJ-9 ports quantity2
Microphone inYes
Headphone outputs1
Certificates
CertificationCE/FCC
Audio
Microphone muteYes
Voice codecsG.711a, G.711u, G.722, G.723.1, G.726, G.729ab
Voice activity detectionYes
Comfort noise generation (CNG)Yes
Noise reductionYes
Packet loss concealment (PLC)Yes
Speakerphone-
Performance
Dual-Tone Multi-Frequency (DTMF) modesIn-band, Out-of band, SIP info
Network
Ethernet LANYes
Ethernet LAN interface typeFast Ethernet
Wi-FiNo
Ethernet LAN data rates10, 100 Mbit/s
BluetoothNo
Networking standardsIEEE 802.1x
Quality of Service (QoS) supportYes
Supported network protocolsSIP2.0 UDP / TCP /TLS, RTP / RTCP /SRTP, STUN, DHCP, PPPoE, 802.1x, Open VPN, SNTP, FTP / TFTP, HTTP / HTTPS, TR069
SyslogYes
Management features
Firmware upgradeableYes
Keypad number of keys23
Number of function keys3
Volume controlDigital
Packaging content
Number of handles included- pc(s)
Cables includedLAN (RJ-45)
Power
AC adapter output voltage5 V
AC adapter output current0.6 A
Power consumption (typical)1.6 W
Power over Ethernet (PoE)No
Operational conditions
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 65 %
Design
Product colorBlack
Handset type-
Product typeIP Phone
Weight & dimensions
Width101 mm
Depth147 mm
Height107.5 mm
Package width197 mm
Package depth110 mm
Package height62 mm
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Fanvil X2 below.

What certifications does the Fanvil X2 have?

The Fanvil X2 has the following certifications: CE/FCC.

What is the screen size of the Fanvil X2?

The screen size of the Fanvil X2 is 2.8 ".

What is the height of the Fanvil X2?

The Fanvil X2 has a height of 107.5 mm.

What is the screen resolution of the display of the Fanvil X2?

The screen resolution of the Fanvil X2 is 320 x 240 pixels.

What is the width of the Fanvil X2?

The Fanvil X2 has a width of 101 mm.

What is the depth of the Fanvil X2?

The Fanvil X2 has a depth of 147 mm.

Is the manual of the Fanvil X2 available in English?

Yes, the manual of the Fanvil X2 is available in English .

Is your question not listed? Ask your question here

No results