4. Insert two #10 flat-head wood screws (not provided) through the touchpanel and align them
with the two pilot holes.
5. Secure the touchpanel to the tabletop.
6. Replace the cover to the base.
Placement with a Kensington Security Lock
11
Figure 25. TLP Pro 1220TG Base, Showing Kensington Security Slot
For added security, attach a Kensington Security Lock (not provided) to the metal-reinforced slot
on the rear edge of the base. Figure 25 shows the rear edge of the TLP Pro 1220TG base, but
the TLP Pro 1520TG and TLP Pro 1720TG bases are very similar.
Follow the instructions that are provided by the manufacturer to install the lock.
Placement with a SMA-1 swivel mount adapter
Both touchpanels can also be mounted with the optional Extron SMA-1 swivel mount adapter,
which allows them to be mounted permanently and swivel up to 180° in either direction.
1. Remove the back cover and base cover (see Removing the Back and Base Covers on
the previous page).
2. Attach the conduit, insulation disk, and swivel disk and configure the set screws to allow for
the degree of swivel that is required (see the SMA-1 Swivel Mount Adapter Kit User Guide,
at www.extron.com).
3. Place the mounting hole in the base over the conduit of the SMA-1.
4. Secure the unit with the backing plate and locking nut as described in the SMA-1 Swivel
Mount Adapter Kit User Guide.
VESA Mounting
The TLP Pro 1220TG, 1520TG, and 1720TG touch panels have VESA FDMI Type D 100 mm
mounting patterns that can be used for VESA mounting with an appropriate third-party mounting
kit.
Before VESA mounting, the base of the touchpanel must be removed.
1. Remove the back cover and base cover (see Removing the Back and Base Covers).
2. If necessary, remove cables from the raceway in the base (see figure 5 on page 12).
3. Remove the cables routed through the base. If necessary, cut the plastic ties that bundle the
cables together.
4. Remove the screws holding the hinges to the touchpanel (see figure 3 on page 8).
NOTE: The spanner drive screws holding the hinges require a #6 spanner bit or
#6 spanner head screwdriver (not provided).
5. Lift the TLP away from the base.
6. Follow the instructions provided with the VESA mounting kit.
TLP Pro 1220, TLP Pro 1520, and TLP Pro 1720 Series • Mounting29
Manual
View the manual for the Extron TLP Pro 1720TG here, for free. This manual comes under the category monitors and has been rated by 1 people with an average of a 7.9. This manual is available in the following languages: English. Do you have a question about the Extron TLP Pro 1720TG or do you need help? Ask your question here
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Extron TLP Pro 1720TG below.
What screen dimensions does my monitor have?
The size of your monitor is usually expressed in inches, 1 inch is 2.54 centimetres. The size is the diagonal size of your monitor, so you measure the screen from bottom left to top right.
What is HDMI?
HDMI stands for High-Definition Multimedia Interface. An HDMI cable is used to transport audio and video signals between devices.
What is the screen size of the Extron TLP Pro 1720TG?
The screen size of the Extron TLP Pro 1720TG is 17.3 ".
What is the screen resolution of the display of the Extron TLP Pro 1720TG?
The screen resolution of the Extron TLP Pro 1720TG is 1920 x 1080 pixels.
Is the manual of the Extron TLP Pro 1720TG available in English?
Yes, the manual of the Extron TLP Pro 1720TG is available in English .
Need help?
Do you have a question about the Extron and is the answer not in the manual?
Question and answer
Number of questions: 0