Extron SMD 202 manual

Extron SMD 202
9.2 · 1
PDF manual
 · 179 pages
English
manualExtron SMD 202
4. Select Install the software automatically (Recommended)(see figure 114,
4
on the previous page).
NOTE: You do not need to insert an installation disc.
5. Click Next (
5
).
The PC locates the driver and installs it.
6. When the Completed dialog opens, click Finish to close the wizard.
NOTE: The wizard opens only on the first occasion you connect the SMD202 to a
USB port. The wizard reopens only if you connect the SMD202 to a different USB
port or if you connect a different piece of equipment, requiring a different driver, to
the same USB port.
7. Configure the SMD202 as required.
NOTE: There are three SIS commands you may find useful at this point:
E CI
]
returns the current IP address.
E 1DH
]
enables DHCP mode.
E 2BOOT
]
must be sent after the above commands to restart the network
interface and apply the changes.
Use DataViewer (see DataViewer on page165) to send the commands and view the
results.

LAN (Ethernet) Port

The rear panel LAN connector on the device can be connected to an Ethernet LAN or WAN.
Communication between the device and the controlling PC is via Telnet (a TCP socket
using port 23). The Telnet port can be changed, if necessary, via SIS or using the SMD202
user interface. This connection makes SIS control of the device possible using a computer
connected to the same LAN or WAN. The SIS commands and behavior of the product are
common to the commands and behavior the product exhibits when communicating by
serial port or USB.

Ethernet Connection

The Ethernet cable can be terminated as a straight-through cable or a crossover cable and
must be properly terminated for your application (see figure 115).
Crossover cable — Direct connection between the computer and the SMD202.
Patch (straight) cable — Connection of the SMD202 to an Ethernet LAN.
12345678
RJ-45
Connector
Insert Twisted
Pair Wires
Pins:
A cable that is wired as TIA/EIA T568A at one
end and T568B at the other (Tx and Rx pairs
reversed) is a "crossover" cable.
A cable wired the same at both ends is called
a "straight-through" cable because no pin/pair
assignments are swapped.
T568A T568B T568B T568B
Straight-through Cable
(for connection to a switch, hub, or router)
End 1 End 2
Pin Wire Color Pin Wire Color
1 white-orange 1 white-orange
2 orange 2 orange
3 white-green 3 white-green
4 blue 4 blue
5 white-blue 5 white-blue
6 green 6 green
7 white-brown 7 white-brown
8 brown 8 brown
Crossover Cable
(for direct connection to a PC)
End 1 End 2
Pin Wire Color Pin Wire Color
1 white-orange 1 white-green
2 orange 2 green
3 white-green 3 white-orange
4 blue 4 blue
5 white-blue 5 white-blue
6 green 6 orange
7 white-brown 7 white-brown
8 brown 8 brown
Figure 118. RJ-45 Ethernet Connector Pin Assignments
129SMD202 • Remote Communication and Control

Manual

View the manual for the Extron SMD 202 here, for free. This manual comes under the category digital decoder and has been rated by 1 people with an average of a 9.2. This manual is available in the following languages: English. Do you have a question about the Extron SMD 202 or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Extron and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Extron SMD 202 specifications

Below you will find the product specifications and the manual specifications of the Extron SMD 202.

General
BrandExtron
ModelSMD 202 | 60-1306-01
Productdigital decoder
LanguageEnglish
FiletypeUser manual (PDF)
Performance
Channels quantity- channels
Maximum video resolution1920 x 1200 pixels
Network
Ethernet interface typeGigabit Ethernet
Ethernet LAN data rates10,100,1000 Mbit/s
Cabling technology10/100/1000BaseE-T(X)
Ports & interfaces
Number of HDMI outputs1
USB 2.0 ports quantity1
Ethernet LAN (RJ-45) ports1
RS-232 ports1
Power
AC adapter input voltage100-240 V
AC adapter frequency50/60 Hz
Power consumption (max)15.8 W
Operational conditions
Operating temperature (T-T)0 - 50 °C
Operating relative humidity (H-H)10 - 90 %
Storage temperature (T-T)-40 - 70 °C
Storage relative humidity (H-H)10 - 90 %
Weight & dimensions
Width222 mm
Depth152 mm
Height25 mm
Weight500 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Extron SMD 202 below.

What is the weight of the Extron SMD 202?

The Extron SMD 202 has a weight of 500 g.

What is the height of the Extron SMD 202?

The Extron SMD 202 has a height of 25 mm.

What is the width of the Extron SMD 202?

The Extron SMD 202 has a width of 222 mm.

What is the depth of the Extron SMD 202?

The Extron SMD 202 has a depth of 152 mm.

Is the manual of the Extron SMD 202 available in English?

Yes, the manual of the Extron SMD 202 is available in English .

Is your question not listed? Ask your question here

No results