Extron RS-232 and IR Control manual

Extron RS-232 and IR Control
7.8 · 1
PDF manual
 · 56 pages
English
manualExtron RS-232 and IR Control

SIS Control

The MLC can be remotely controlled via a host computer or other control device that
is attached to the MLC front panel USB port. You can issue Simple Instruction Set
(SIS) commands to the MLC via the USB interface of your computer or control device
with a communication software program such as Extron DataViewer or HyperTerminal.
This section contains a list of the SIS commands available for the MLC and describes
procedures for issuing them. The following topics are covered:
Host-to-Controller Communications
Using the Command and Response Table
Command and Response Table for SIS Commands

Host-to-Controller Communications

SIS commands consist of strings of one or more characters per field. No special
characters are required to begin or end a command sequence. When the MLC determines
that a command is valid, it executes the command and sends a response to the host
device.
Most responses from the MLC to the host end with a carriage return and a line feed
(CR/LF =
]
), which signals the end of the response character string.

Controller-initiated Messages

When a local event such as a front panel button press takes place, the MLC responds by
sending a message to the host, indicating what selection was entered. No response is
required from the host. For example:
BtnoB*04
]
This message would appear if button 4 (by default configured as an input selection button)
is pressed.

Error Responses

If the MLC is unable to execute a command it receives because the command is invalid
or contains invalid parameters, the controller returns an error response to the host. This
response consists of the letter E followed by a number and a carriage return with a line
feed. The following error response codes can be returned:
E10 – Invalid command or parameter
E13 – Invalid value (out of range)
E14 – Not valid for this configuration
E22 – Busy
MLC 55 Series MediaLink Controllers • SIS Control 42

Manual

View the manual for the Extron RS-232 and IR Control here, for free. This manual comes under the category remote controllers and has been rated by 1 people with an average of a 7.8. This manual is available in the following languages: English. Do you have a question about the Extron RS-232 and IR Control or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Extron and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Extron RS-232 and IR Control specifications

Below you will find the product specifications and the manual specifications of the Extron RS-232 and IR Control.

General
BrandExtron
ModelRS-232 and IR Control | 60-1390-03
Productremote controller
EAN5712505902448
LanguageEnglish
FiletypeUser manual (PDF)
Design
InterfaceIR Wireless/Wired
Product colorWhite
Remote control proper useAV switch
Input typePress buttons
Backlight buttonsYes
Display
Built-in displayNo
Performance
Number of devices supported-
Maximum range- m
Battery
RechargeableNo
Built-in batteryNo
Power
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Power consumption (transmitter) (max)1.1 W
Operational conditions
Operating temperature (T-T)0 - 50 °C
Operating temperature (T-T)32 - 122 °F
Storage temperature (T-T)-40 - 70 °C
Storage temperature (T-T)-40 - 158 °F
Operating relative humidity (H-H)10 - 90 %
Storage relative humidity (H-H)10 - 90 %
Weight & dimensions
Width44.7 mm
Depth35.8 mm
Height71.4 mm
Weight100 g
Packaging data
Package width187 mm
Package depth264 mm
Package height76 mm
Package weight790 g
Logistics data
Harmonized System (HS) code85299097
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Extron RS-232 and IR Control below.

What is the weight of the Extron RS-232 and IR Control?

The Extron RS-232 and IR Control has a weight of 100 g.

A battery in my remote controller has started to corrode. Is the device still safe to use?

The product can still be used safely after proper cleaning. Remove the battery with gloves and clean the battery compartment with a toothbrush and vinegar. After drying, new batteries can be inserted into the device.

What is the height of the Extron RS-232 and IR Control?

The Extron RS-232 and IR Control has a height of 71.4 mm.

What is the width of the Extron RS-232 and IR Control?

The Extron RS-232 and IR Control has a width of 44.7 mm.

What is the depth of the Extron RS-232 and IR Control?

The Extron RS-232 and IR Control has a depth of 35.8 mm.

Is the manual of the Extron RS-232 and IR Control available in English?

Yes, the manual of the Extron RS-232 and IR Control is available in English .

Is your question not listed? Ask your question here

No results