Extron RS-232 and IR Control manual

Extron RS-232 and IR Control
7.8 · 1
PDF manual
 · 56 pages
English
manualExtron RS-232 and IR Control

Front Panel Features

By default, the front panel button modes are set to perform the functions with which they
are named. Using the MLC configuration program, you can select other functions and
operating modes for these buttons (see the configuration program help file).
A
Display power On and Off buttons — After configuring these buttons, use them to
turn the connected display device or switcher on and off. The face of the On button
contains a nub (
I
), which lets you identify the button location on the panel by touch.
When the On button is pressed, it blinks rapidly while the connected device is
warming up (30 seconds by default). When the Off button is pressed, it blinks slowly
while the device is cooling down (60 seconds by default). When this delay period has
elapsed, the power button that was pressed remains brightly lit.
In addition, the On button blinks red slowly if the MLC detects incompatibility between
the firmware and software versions.
By default, these two buttons are in Power mode, meaning that only one of these
buttons can be selected (active) at once.
B
IR Learning sensor — This sensor enables the MLC to learn IR commands from the
hand-held remote control of a display device or switcher. The IR-learned commands
are used to create an IR driver using the program, then configured to be played back
with a press of any desired button (see IR Learning on page 20).
C
Input selection buttons — By default, these buttons are labeled PC and Video.
Their default mode is Input mode, which means that, like in Power mode, only one of
these buttons can be active at a time. When one input button is pressed (activated), it
lights brightly and all others in the same mode become dim (inactive).
D
Reset LED — When you press the Reset button, this green LED lights and remains
lit until released (see Resetting on page 26).
E
Reset button — Using the provided Extron Tweeker or other small screwdriver, press
this recessed button to initiate resets to factory firmware or configuration resets (see
Resetting).
F
Volume buttons (all models except MLC 55 RS VC) — By default, these buttons
are set to adjust the audio volume of the display device. Each volume button is in
Volume mode, which means that it lights when pressed and remains lit, while the
display volume increments (Vol
>
button) or decrements (Vol
<
button), until released.
NOTE: On the MLC 55 RS VC, you are not able to set any buttons to Volume
mode. By default these two buttons are configured for input selection (see
figure 4,
C
, on page 7).
G
Volume control knob (MLC 55 RS VC only)— Rotate this knob to increase or
decrease the volume on the Extron amplifier with remote volume port capability that is
connected to the volume control module.
H
USB configuration port — Connect a USB cable (USB A-to-USB mini-B) between
your computer and this port to configure the MLC via the configuration program and
to update the firmware.
NOTE: Before performing IR Learning to create a driver, check to see if an Extron
driver exists for your device (see Obtaining Device Drivers on page 34).
I
Power On button Identification nub — Button 1, usually configured as the Power
On button, contains a raised nub on its face that lets the Power On button be identified
by touch.
MLC 55 Series MediaLink Controllers • Installation and Operation 9

Manual

View the manual for the Extron RS-232 and IR Control here, for free. This manual comes under the category remote controllers and has been rated by 1 people with an average of a 7.8. This manual is available in the following languages: English. Do you have a question about the Extron RS-232 and IR Control or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Extron and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Extron RS-232 and IR Control specifications

Below you will find the product specifications and the manual specifications of the Extron RS-232 and IR Control.

General
BrandExtron
ModelRS-232 and IR Control | 60-1390-03
Productremote controller
EAN5712505902448
LanguageEnglish
FiletypeUser manual (PDF)
Design
InterfaceIR Wireless/Wired
Product colorWhite
Remote control proper useAV switch
Input typePress buttons
Backlight buttonsYes
Display
Built-in displayNo
Performance
Number of devices supported-
Maximum range- m
Battery
RechargeableNo
Built-in batteryNo
Power
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Power consumption (transmitter) (max)1.1 W
Operational conditions
Operating temperature (T-T)0 - 50 °C
Operating temperature (T-T)32 - 122 °F
Storage temperature (T-T)-40 - 70 °C
Storage temperature (T-T)-40 - 158 °F
Operating relative humidity (H-H)10 - 90 %
Storage relative humidity (H-H)10 - 90 %
Weight & dimensions
Width44.7 mm
Depth35.8 mm
Height71.4 mm
Weight100 g
Packaging data
Package width187 mm
Package depth264 mm
Package height76 mm
Package weight790 g
Logistics data
Harmonized System (HS) code85299097
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Extron RS-232 and IR Control below.

What is the weight of the Extron RS-232 and IR Control?

The Extron RS-232 and IR Control has a weight of 100 g.

A battery in my remote controller has started to corrode. Is the device still safe to use?

The product can still be used safely after proper cleaning. Remove the battery with gloves and clean the battery compartment with a toothbrush and vinegar. After drying, new batteries can be inserted into the device.

What is the height of the Extron RS-232 and IR Control?

The Extron RS-232 and IR Control has a height of 71.4 mm.

What is the width of the Extron RS-232 and IR Control?

The Extron RS-232 and IR Control has a width of 44.7 mm.

What is the depth of the Extron RS-232 and IR Control?

The Extron RS-232 and IR Control has a depth of 35.8 mm.

Is the manual of the Extron RS-232 and IR Control available in English?

Yes, the manual of the Extron RS-232 and IR Control is available in English .

Is your question not listed? Ask your question here

No results