Extron PowerCage FOX Tx HDMI MM manual

Extron PowerCage FOX Tx HDMI MM
6.6 · 1
PDF manual
 · 49 pages
English
manualExtron PowerCage FOX Tx HDMI MM
Using the Command and Response Tables
The command and response tables begin on the next page. Either uppercase or lower case
letters are acceptable in the command field except where indicated for the audio level (gain
and attenuation) commands. Symbols are used throughout the table to represent variables in
the command and response fields. Command and response examples are shown throughout
the table. The ASCII to HEX conversion table below is for use with the command and
response table.
ASCII to Hex Conversion Table
Space
Symbol definitions for transmitter SIS commands
] = Carriage return/line feed
} = Carriage return (no line feed)
| = Pipe (can be used interchangeably with the } character)
= space
E = Escape key
W = Can be used interchangeably with the E character
X! = EDID hex switch position 00 = N/A 08 = 1360 x 768
01 = RS-232 control 09 = 1366 x 768
02 = 800 x 600 10 = 1400 x 1050
03 = 1024 x 768 11 = 1440 x 900
04 = 720p* 12 = 1600 x 1200
05 = 1280 x 768 13 = 1680 x 1050
06 = 1280 x 800 14 = 1080p*
07 = 1280 x 1024 15 = 1920 x 1200
* 720p and 1080p also include a block for embedded audio; all other
positions are video only
X@ = Refresh rate 1 = 50 Hz 2 = 60 Hz
X# = EDID See the table on page 20.
X$ = Native resolution
Resolution and rate in an easily-viewed format, such as “800x600@60Hz“.
X% = EDID record 128 or 256 bytes
X^ = Audio gain adjustment range 00 to 10
X& = Audio level adjustment range –18 to +10 (in 1.0 dB steps)
X* = Audio attenuation adjustment range 00 to 18
X( = Mode switch position and enable or disable status 0 = off (down) or disable 1 = on (up) or enable
X1) = Link and input status 0 = link or input not detected 1 = link or input detected
X1! = Internal temperature nnnF•nnC
X1@ = Transmission mode SM = singlemode MM = multimode
X1# = Firmware version v.vv
X1$ = Sync frequency xxx.xx (frequency in kHz [H] or Hz [V])
PowerCage FOX HDMI • Remote Control 19

Manual

View the manual for the Extron PowerCage FOX Tx HDMI MM here, for free. This manual comes under the category AV extenders and has been rated by 1 people with an average of a 6.6. This manual is available in the following languages: English. Do you have a question about the Extron PowerCage FOX Tx HDMI MM or do you need help? Ask your question here

Need help?

Do you have a question about the Extron and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Extron PowerCage FOX Tx HDMI MM specifications

Below you will find the product specifications and the manual specifications of the Extron PowerCage FOX Tx HDMI MM.

General
BrandExtron
ModelPowerCage FOX Tx HDMI MM | 70-889-11
ProductAV extender
LanguageEnglish
FiletypeUser manual (PDF)
Features
TypeAV transmitter
Maximum resolution4096 x 2160 pixels
Maximum refresh rate60 Hz
Bandwidth4.95 Gbit/s
Power
Power consumption (typical)6.02 W
AC input voltage12 V
Operational conditions
Operating temperature (T-T)0 - 50 °C
Storage temperature (T-T)-40 - 70 °C
Operating relative humidity (H-H)10 - 90 %
Storage relative humidity (H-H)10 - 90 %
Ports & interfaces
HDMI in1
3.5 mm (1/8-inch) inYes
RS-232 input ports2
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Extron PowerCage FOX Tx HDMI MM below.

Is the manual of the Extron PowerCage FOX Tx HDMI MM available in English?

Yes, the manual of the Extron PowerCage FOX Tx HDMI MM is available in English .

Is your question not listed? Ask your question here

No results