Extron PowerCage FOX Tx HDMI MM manual

Extron PowerCage FOX Tx HDMI MM
6.6 · 1
PDF manual
 · 49 pages
English
manualExtron PowerCage FOX Tx HDMI MM

Simple Instruction Set Control

Host-to-unit Instructions

SIS commands consist of one or more characters per field. No special characters are required
to begin or end a command character sequence. When a command is valid, the unit
executes the command and sends a response to the host device. All responses from the unit
to the host end with a carriage return and a line feed (CR/LF =
]
), which signals the end of
the response character string. A string is one or more characters.

Unit-initiated Messages

When a local event, such as an equipment power-up, occurs, the unit responds by sending a
message to the host. The unit-initiated messages are listed below:
(c) Copyright 20nn, Extron Electronics PowerCage FOX Tx HDMI,
Vn.nn, 70-889-nn
]]
- or -
(c) Copyright 20nn, Extron Electronics PowerCage FOX Rx HDMI,
Vn.nn, 70-889-nn
]]
The connected unit issues the appropriate copyright message (above) when it first powers
on. Vn.nn is the firmware version number; 70-889-nn is the part number of the connected
unit.
Reconfig
]
The unit sends the Reconfig message whenever the video input signal to the transmitter is
changed.
1Lnknn2LnknnVidnnAudnn
]
The unit sends the status message whenever a change in the fiber link and video and audio
connection occurs. nn is the link or input status, where 0 = link or input not detected,
1 = link or input detected, and -- = not applicable for this unit.
EmbedAudn
]
The unit sends the Embedded audio message whenever a change in the position of the
receiver HDMI Audio switch occurs. n is the switch position, where 0 = embedded audio is
muted and 1 = unmuted.

Error Responses

When the unit receives a valid SIS command, it executes the command and sends a response
to the host device. If the unit is unable to execute the command because the command is
invalid or it contains invalid parameters, the unit returns an error response to the host. The
error response codes are:
E10 - Invalid command
E11 - Invalid preset number
E13 - Invalid parameter
E14 - Invalid command for this configuration
PowerCage FOX HDMI • Remote Control 18

Manual

View the manual for the Extron PowerCage FOX Tx HDMI MM here, for free. This manual comes under the category AV extenders and has been rated by 1 people with an average of a 6.6. This manual is available in the following languages: English. Do you have a question about the Extron PowerCage FOX Tx HDMI MM or do you need help? Ask your question here

Need help?

Do you have a question about the Extron and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Extron PowerCage FOX Tx HDMI MM specifications

Below you will find the product specifications and the manual specifications of the Extron PowerCage FOX Tx HDMI MM.

General
BrandExtron
ModelPowerCage FOX Tx HDMI MM | 70-889-11
ProductAV extender
LanguageEnglish
FiletypeUser manual (PDF)
Features
TypeAV transmitter
Maximum resolution4096 x 2160 pixels
Maximum refresh rate60 Hz
Bandwidth4.95 Gbit/s
Power
Power consumption (typical)6.02 W
AC input voltage12 V
Operational conditions
Operating temperature (T-T)0 - 50 °C
Storage temperature (T-T)-40 - 70 °C
Operating relative humidity (H-H)10 - 90 %
Storage relative humidity (H-H)10 - 90 %
Ports & interfaces
HDMI in1
3.5 mm (1/8-inch) inYes
RS-232 input ports2
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Extron PowerCage FOX Tx HDMI MM below.

Is the manual of the Extron PowerCage FOX Tx HDMI MM available in English?

Yes, the manual of the Extron PowerCage FOX Tx HDMI MM is available in English .

Is your question not listed? Ask your question here

No results