Extron KP 6 manual

Extron KP 6
5.9 · 1
PDF manual
 · 3 pages
English
manualExtron KP 6
Keypad Remote Controls • Installation and OperationKeypad Remote Controls • Installation and Operation

Installation and Operation

32

Introduction

The KP 6 is designed to control MSW 4 Series, SW AV Series (4 and 6
input models only), SW VGA/Ars Series, and SW RGBHV/ A Series
switchers, or other Extron products with contact closure ports or
ports labeled as “Remote.”
The KP 6 is a contact closure remote for selecting the switcher’s input.
When a number key is pressed, the wire associated with that input is
momentarily shorted to ground, making the switcher switch to that
input.
The KP 6 can control up to 6 inputs and requires no power.

Installation

Installation with a 9-pin D-sub connector

Many switchers, such as the SW6 VGA Ars Switcher, come equipped
with a 9-pin D-sub connector. To use the KP 6 Keypad Remote
Control on this type of switcher, install it as follows:
1. Power down the switcher.
2. Connect the KP 6 adapter’s 9-pin plug to the contact closure
connector on the switcher’s rear panel.
3. Position the KP 6 Keypad for the most convenient operation.
4. Power up the switcher.
Figure 1 — Typical KP 6 application (with 9-pin D-
sub connector)
Figure 2 — 9-pin Sub-D connector pinout

Installation with a captive screw connector

Some switchers, such as the MSW 4 Series, are not equipped with
9-pin D-sub connectors and have a 3.5mm, 5-pole captive screw
connector (labeled “Contact”) instead. In order to use the KP 6
Keypad Remote Control with these switchers, a captive screw
connector (included with the switcher) must be used. To use a captive
screw connector, the existing 9-pin D-sub connector must be removed
from the cable and a captive screw connector installed.
To install the captive screw connector, remove the wire from the 9-pin
D-sub connector, then strip the wires and insert them into the new
connector (supplied with the switcher). Wire the connector as shown
here. Tighten the screws to secure the wires. Clip off the green and
blue wires.
Do not tin the stripped wire leads before installing the
captive screw connector. Tinned wires are not as secure
in the captive screw connectors and could pull out.
Install the KP 6 Keypad Remote Control on this type of switcher as
follows:
1. Rewire the connector on the KP 6 Keypad Remote Control.
2. Power down the switcher.
3. Connect the KP 6 adapter’s captive screw connector to the
“Contact” connector on the switcher’s rear panel.
4. Position the KP 6 Keypad for the most convenient operation.
5. Power up the switcher.
Brown
Red
Orange
Yellow
Black
4
3
2
1
25 foot
cable
KP 6 Keypad
Remote Control
SW6 VGA Ars Switcher
SW6 VGA Ars
REMOTE
100-240V 0.2A
INPUTS
1
2
3
4
5
50-60Hz
OUTPUT
OUTPUT
LR
SW6 VGA Ars
6
niP erusolctcatnoC n Wire coloroitcnuF
1
1#nI 1 Brown#tupnI
2
3
4
2#nI 2 Red#tupnI
5 dnG d BlacknuorglangiS
6
3#nI 3 Orange#tupnI
7
4#nI 4 Yellow#tupnI
8
5#nI 5 Green#tupnI
9
6#nI 6 Blue#tupnI
Not used
Not used
Male
15
69

Manual

View the manual for the Extron KP 6 here, for free. This manual comes under the category remote controllers and has been rated by 1 people with an average of a 5.9. This manual is available in the following languages: English. Do you have a question about the Extron KP 6 or do you need help? Ask your question here

Need help?

Do you have a question about the Extron and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Extron KP 6 specifications

Below you will find the product specifications and the manual specifications of the Extron KP 6.

General
BrandExtron
ModelKP 6 | 60-111-20
Productremote controller
LanguageEnglish
FiletypeUser manual (PDF)
Design
InterfaceWired
Product colorBlack
Remote control proper useAV switch
Brand compatibilityExtron
Compatible productsSW VGA, SW RGBHV, SW AV Series
Input typePress buttons
Backlight buttonsNo
Display
Built-in displayNo
Performance
Number of devices supported-
Maximum range7.6 m
Battery
Rechargeable-
Weight & dimensions
Weight- g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Extron KP 6 below.

What is the weight of the Extron KP 6?

The Extron KP 6 has a weight of - g.

A battery in my remote controller has started to corrode. Is the device still safe to use?

The product can still be used safely after proper cleaning. Remove the battery with gloves and clean the battery compartment with a toothbrush and vinegar. After drying, new batteries can be inserted into the device.

Is the manual of the Extron KP 6 available in English?

Yes, the manual of the Extron KP 6 is available in English .

Is your question not listed? Ask your question here

No results