Extron JMP 9600 HD manual

Extron JMP 9600 HD
9.2 · 1
PDF manual
 · 122 pages
English
manualExtron JMP 9600 HD
TIP: When you are in a multiple player, master/slave conguration, you should stop all
slave players before loading new content on the master player if that content has a
different frame rate than the currently-loaded content.
1. Stop all players.
2. Load new content on the master player.
3. Load new content on the slave players.
4. Send the tcreceive and tcplayat commands.
5. Use the tcstart command to begin playback of the new content.
Changing content on the master player without stopping the slave players may
result in a ashing or green screen output to the displays until the new content is
loaded on the slave players.

Configuring LTC for Synchronized Multi-player Operation

Control Example — Single file using separate control

This example is the simplest type of synchronized show, requiring two players. Each player
loads a single clip and plays it through to the end. This is an example of a technique that
might be used in a 3D theater.
The following table assumes that you want to play the file <
folder>/<name> in channel 1
of two JMP 9600 units, beginning at the 1-hour LTC mark, with a 5 second LTC lead in
(pre-roll). To play properly, the show-control system needs to trigger the following events in
the sequence shown.
Command to Master Player Command to Slave Player Function
LoadClip 1 <folder>/<name>
]
LoadClip 1 <folder>/<name>
]
Load a clip (cue it) into channel 1 of both media players .
For a playlist, use the LoadPlaylist command.
NOTE: The media players respond to the LoadClip commands with OK
]
after the file loading process is completed. You may need
to build a delay into the sequence required between the LoadClip and Tcgenerate commands. The actual delay required is
dependent on the size of the clip file and must be determined by experimentation, but start with 1 second.
Tcgenerate 00:59:55:00
]
Program the master player as the LTC generator.
Tcreceive
]
Program the slave player as the LTC receiver.
TcPlayAt <1> 01:00:00:00
]
TcPlayAt <1> 01:00:00:00
]
Set both media players to begin playing at a specific LTC
timestamp.
Tcstart
]
Set the master player to begin LTC generation.
Both media players begin showing video at the LTC timestamp specied in the Tcplayat
command.
NOTE: Adjustments to the Tcplayat timestamp on the slave player can correct for
encoding errors.
When the media player is set as a timecode master and a clip or playlist is loaded, the player
begins to generate LTC as a response to either of two commands:
Play — This command can be from the front panel Play/Pause ( ) button, the Play ( )
control on the Player Control HTML page, or the Play MSVPP command.
TcStart This command can only be sent via MSVPP (although when you have
loaded a playlist with defined timecode parameters and you then click the Play control
( ) to start the show, it has the same affect as issuing the TCStart command).
JMP 9600 Media Player • Detailed System Interaction 88

Manual

View the manual for the Extron JMP 9600 HD here, for free. This manual comes under the category media players and has been rated by 1 people with an average of a 9.2. This manual is available in the following languages: English. Do you have a question about the Extron JMP 9600 HD or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Extron and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Extron JMP 9600 HD specifications

Below you will find the product specifications and the manual specifications of the Extron JMP 9600 HD.

General
BrandExtron
ModelJMP 9600 HD | 60-1135-01
Productmedia player
LanguageEnglish
FiletypeUser manual (PDF)
Storage
Built-in storage mediaNo
Storage media typeNot available
Total storage capacity0 GB
Features
Video formats supported-
Image formats supported-
Supported radio bandsNot supported
Product colorBlack
Video
Full HDYes
Maximum video resolution2048 x 1080 pixels
HD typeFull HD
Audio
Audio output channels- channels
Impedance75 Ω
Ports & interfaces
HDMI ports quantity0
HDCP-
Ethernet LAN (RJ-45) ports2
USB 2.0 ports quantity0
Audio (L/R) out0
Component video (YPbPr/YCbCr) out0
Composite video out0
DVI-I ports quantity2
Digital audio optical out0
Digital audio coaxial out0
S/PDIF out portYes
S-Video outputs quantity1
Network
Ethernet LANYes
Ethernet LAN data rates10,100,1000 Mbit/s
Wi-FiNo
Display
Built-in displayYes
Power
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Power consumption (typical)70 W
Operational conditions
Operating temperature (T-T)10 - 40 °C
Operating relative humidity (H-H)10 - 90 %
Weight & dimensions
Width432 mm
Depth394 mm
Height89 mm
Weight10400 g
Packaging data
Package width525 mm
Package depth648 mm
Package height225 mm
Package weight14290 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Extron JMP 9600 HD below.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is the weight of the Extron JMP 9600 HD?

The Extron JMP 9600 HD has a weight of 10400 g.

What is the height of the Extron JMP 9600 HD?

The Extron JMP 9600 HD has a height of 89 mm.

What is the width of the Extron JMP 9600 HD?

The Extron JMP 9600 HD has a width of 432 mm.

What is the depth of the Extron JMP 9600 HD?

The Extron JMP 9600 HD has a depth of 394 mm.

Is the manual of the Extron JMP 9600 HD available in English?

Yes, the manual of the Extron JMP 9600 HD is available in English .

Is your question not listed? Ask your question here

No results