Extron JMP 9600 HD manual

Extron JMP 9600 HD
9.2 · 1
PDF manual
 · 122 pages
English
manualExtron JMP 9600 HD

Digital Inputs and Relays

The Digital Inputs and Relays ports provides optically-isolated digital inputs and relay outputs
that can be controlled by the show control software. See the “Programming Guide
section for the MSVPP commands that activate or are issued by the these ports.
NOTES: By factory default, automatic reporting of Digital Inputs 1 through 4 is
disabled. To enable reporting, use the Set input trigger on MSVPP
command (see the “Programming Guide” section).
Use a single cable for all inputs and relay ports and snap one of the included
ferrite beads on the cable, as close to the unit as possible.
i
Digital Inputs 1 through 4 — These inputs allow the media player to sense
1 2
+ - + -
a discrete signal, such as change in a switch position. Connect the desired
discrete input line to the unit via two poles (+ and –) of a 3.5 mm 4-pole
captive screw connector (see “Optically-isolated Digital Inputs”, on
page 94, for an illustration of a typical input connection).
The media player issues an MSVPP message on Remote port 1 when it detects a
change of state on the digital inputs, prompting the connected device to respond as
appropriate.
j
Power — This port provides +12 VDC power at up to 1.8 A, typically for use
12V
POWER
with Digital Inputs 1 through 4 (item
i
) above. The power is internally
protected. Connect the device requiring power to two poles (12V and
ground [ ]) of a 3.5 mm 4-pole captive screw connector.
WARNING: 12 VDC is always present on this port when the media player is powered
on. Ensure that no conductive material comes into contact with these
terminals.
A typical use of this voltage is shown in “Optically-isolated Digital Inputs,” on
page 94.
k
Relay Outputs — These ports are four sets of NO and NC relay contacts.
NC CNO NC
R1
Connect an external device that you want to be able to switch on or off to the
player via three poles (normally closed [NC], common [C], and normally open
[NO]) of the 3.5 mm 4-pole captive screw connectors.
NOTE: Relays R1 and R4 each are on a single captive screw connector.
Relays R2 and R3 each span two captive screw connectors.
The player toggles the relay on or off in response to an MSVPP signal from the device
connected on Remote port 1 or either LAN port, see “Relay Contacts“ on page 95.
JMP 9600 Media Player • Installation 11

Manual

View the manual for the Extron JMP 9600 HD here, for free. This manual comes under the category media players and has been rated by 1 people with an average of a 9.2. This manual is available in the following languages: English. Do you have a question about the Extron JMP 9600 HD or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Extron and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Extron JMP 9600 HD specifications

Below you will find the product specifications and the manual specifications of the Extron JMP 9600 HD.

General
BrandExtron
ModelJMP 9600 HD | 60-1135-01
Productmedia player
LanguageEnglish
FiletypeUser manual (PDF)
Storage
Built-in storage mediaNo
Storage media typeNot available
Total storage capacity0 GB
Features
Video formats supported-
Image formats supported-
Supported radio bandsNot supported
Product colorBlack
Video
Full HDYes
Maximum video resolution2048 x 1080 pixels
HD typeFull HD
Audio
Audio output channels- channels
Impedance75 Ω
Ports & interfaces
HDMI ports quantity0
HDCP-
Ethernet LAN (RJ-45) ports2
USB 2.0 ports quantity0
Audio (L/R) out0
Component video (YPbPr/YCbCr) out0
Composite video out0
DVI-I ports quantity2
Digital audio optical out0
Digital audio coaxial out0
S/PDIF out portYes
S-Video outputs quantity1
Network
Ethernet LANYes
Ethernet LAN data rates10,100,1000 Mbit/s
Wi-FiNo
Display
Built-in displayYes
Power
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Power consumption (typical)70 W
Operational conditions
Operating temperature (T-T)10 - 40 °C
Operating relative humidity (H-H)10 - 90 %
Weight & dimensions
Width432 mm
Depth394 mm
Height89 mm
Weight10400 g
Packaging data
Package width525 mm
Package depth648 mm
Package height225 mm
Package weight14290 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Extron JMP 9600 HD below.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is the weight of the Extron JMP 9600 HD?

The Extron JMP 9600 HD has a weight of 10400 g.

What is the height of the Extron JMP 9600 HD?

The Extron JMP 9600 HD has a height of 89 mm.

What is the width of the Extron JMP 9600 HD?

The Extron JMP 9600 HD has a width of 432 mm.

What is the depth of the Extron JMP 9600 HD?

The Extron JMP 9600 HD has a depth of 394 mm.

Is the manual of the Extron JMP 9600 HD available in English?

Yes, the manual of the Extron JMP 9600 HD is available in English .

Is your question not listed? Ask your question here

No results