Extron JMP 9600 HD manual

Extron JMP 9600 HD
9.2 · 1
PDF manual
 · 122 pages
English
manualExtron JMP 9600 HD

Configuring the Media Player for Network use via the ARP Command

The ARP (address resolution protocol) command tells your computer to associate the
media MAC (media access control) address of the player with the assigned IP address. You
must then use the ping utility to access the controller, at which point the IP address of the
controller is reconfigured.
Use ARP to congure the IP address as follows:
1. Obtain a valid IP address, such as 10.13.197.7, for the media player from your network
administrator.
2. Obtain the MAC address (UID #) of the media player from the label on its rear panel.
The MAC address should have this format: 00-E0-AA-xx-xx-xx.
3. At the PC, access the MS-DOS command prompt, then enter the arp –s command.
Type in the desired new IP address for the unit (obtained in step 1) and the MAC address
of the unit (from the rear panel of the unit). For example
arp –s 10.13.197.7 00-05-A6-03-69-B0 and then press <Enter>.
The computer returns the command prompt (C:\).
After you issue the arp -s command, the controller changes to the new address and
starts responding to the ping requests to the new address, as described in the next step.
NOTE: You must ping the media player for the IP address change to take place.
The response should show the new IP address, as shown in figure 83.
4. Execute a ping command by entering ping followed by a space and the new IP address
at the command prompt. For example:
ping 10.13.197.7
C:\>ping 10.13.197.7
Pinging 10.13.197.7 with 32 bytes of data:
Reply from 10.13.197.7: bytes=32 time<10ms TTL=128
Reply from 10.13.197.7: bytes=32 time<10ms TTL=128
Reply from 10.13.197.7: bytes=32 time<10ms TTL=128
Reply from 10.13.197.7: bytes=32 time<10ms TTL=128
Ping statistics for 10.13.197.7:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
Figure 83. Ping with New Address
NOTE: You can reconnect using either Telnet or a web browser to verify that the
update was successful.
5. After verifying that the IP address change was successful, enter and issue the arp –d
command at the Command prompt. For example:
arp –d 10.13.197.7 removes 10.13.197.7 from the ARP table
or
arp –d* removes all static IP addresses from the ARP table.
JMP 9600 Media Player • Ethernet Connection 107

Manual

View the manual for the Extron JMP 9600 HD here, for free. This manual comes under the category media players and has been rated by 1 people with an average of a 9.2. This manual is available in the following languages: English. Do you have a question about the Extron JMP 9600 HD or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Extron and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Extron JMP 9600 HD specifications

Below you will find the product specifications and the manual specifications of the Extron JMP 9600 HD.

General
BrandExtron
ModelJMP 9600 HD | 60-1135-01
Productmedia player
LanguageEnglish
FiletypeUser manual (PDF)
Storage
Built-in storage mediaNo
Storage media typeNot available
Total storage capacity0 GB
Features
Video formats supported-
Image formats supported-
Supported radio bandsNot supported
Product colorBlack
Video
Full HDYes
Maximum video resolution2048 x 1080 pixels
HD typeFull HD
Audio
Audio output channels- channels
Impedance75 Ω
Ports & interfaces
HDMI ports quantity0
HDCP-
Ethernet LAN (RJ-45) ports2
USB 2.0 ports quantity0
Audio (L/R) out0
Component video (YPbPr/YCbCr) out0
Composite video out0
DVI-I ports quantity2
Digital audio optical out0
Digital audio coaxial out0
S/PDIF out portYes
S-Video outputs quantity1
Network
Ethernet LANYes
Ethernet LAN data rates10,100,1000 Mbit/s
Wi-FiNo
Display
Built-in displayYes
Power
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Power consumption (typical)70 W
Operational conditions
Operating temperature (T-T)10 - 40 °C
Operating relative humidity (H-H)10 - 90 %
Weight & dimensions
Width432 mm
Depth394 mm
Height89 mm
Weight10400 g
Packaging data
Package width525 mm
Package depth648 mm
Package height225 mm
Package weight14290 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Extron JMP 9600 HD below.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

What is the weight of the Extron JMP 9600 HD?

The Extron JMP 9600 HD has a weight of 10400 g.

What is the height of the Extron JMP 9600 HD?

The Extron JMP 9600 HD has a height of 89 mm.

What is the width of the Extron JMP 9600 HD?

The Extron JMP 9600 HD has a width of 432 mm.

What is the depth of the Extron JMP 9600 HD?

The Extron JMP 9600 HD has a depth of 394 mm.

Is the manual of the Extron JMP 9600 HD available in English?

Yes, the manual of the Extron JMP 9600 HD is available in English .

Is your question not listed? Ask your question here

No results