Extron DMP 128 Plus C manual

Extron DMP 128 Plus C
8.4 · 1
PDF manual
 · 188 pages
English
manualExtron DMP 128 Plus C
DMP 128 Plus • Remote Control and Configuration 148

Command and Response Table for VoIP SIS Commands

NOTE: All SIS responses in this section are in Verbose modes 2 and 3. In Verbose modes 0 or 1,
responses will not be tagged.
Command ASCII command
(host to device)
Response
(device to host)
Additional description
Call Control
End call
EENDX!,X@VOIP} VoipENDX!,X@,X$]
End call on all
appearances
EENDX!VOIP} VoipENDX!,1,X$]
Dial string
EDIALX!,X#VOIP} VoipDIALX!,X#,X$]
Dial digits
EDDX!,X@,X#VOIP} VoipDDX!,X@,X#,X$]
Answer
EANSX!,X@VOIP} VoipANSX!,X@,X$]
Reject
EREJX!,X@VOIP} VoipREJX!,X@,X$]
Hold

EHOLDX!,X@,X2$

VOIP}
VoipHOLDX!,X@,X2$,
X$]
Call Settings
Set do not disturb
EDNDX!,X&VOIP} VoipDNDX!,X&]
Get do not disturb
status
EDNDX!VOIP} VoipDNDX!,X&]
Set auto answer
EAAX!,X*VOIP} VoipAAX!,X*]
Get auto answer status
EAAX!VOIP} VoipAAX!,X*]
Set auto answer delay
EADX!,X(VOIP} VoipADX!,X(]
Get auto answer delay
status
EADX!VOIP} VoipADX!,X(]
KEY:
X!
= Line number 1 through 8
X@
= Appearance number 1 through 8 (where 1 is the originating two-party call)
X#
= Phone number No spaces allowed. Valid characters are 0 - 9, *, #
X$
= Return code 0 = ok, 1 = fail

X&

= Operating state 1 = enable, 0 = disable
X*
= Auto answer mode 0 = disabled, 1 = delay (seconds), 2 = follow SIP header
X(
= Delay value Represents time in seconds.
X2$
= Hold status 0 = off, 1 = on-hold

Manual

View the manual for the Extron DMP 128 Plus C here, for free. This manual comes under the category not categorized and has been rated by 1 people with an average of a 8.4. This manual is available in the following languages: English. Do you have a question about the Extron DMP 128 Plus C or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Extron and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Extron DMP 128 Plus C specifications

Below you will find the product specifications and the manual specifications of the Extron DMP 128 Plus C.

General
BrandExtron
ModelDMP 128 Plus C | 60-1512-01
Productnot categorized
EAN5711783372820
LanguageEnglish
FiletypeUser manual (PDF)
Ports & interfaces
Number of inputs12 inputs
Features
Total Harmonic Distortion plus Noise (THD+N)0.01 %
Frequency range20 - 20000 Hz
Signal-to-Noise Ratio (SNR)115 dB
Input impedance10000 Ω
Housing colorGray
Housing materialMetal
Power
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Power consumption (typical)29.4 W
Operational conditions
Operating temperature (T-T)0 - 50 °C
Storage temperature (T-T)-40 - 70 °C
Operating relative humidity (H-H)10 - 90 %
Storage relative humidity (H-H)10 - 90 %
Weight & dimensions
Width442 mm
Depth241 mm
Height43 mm
Weight2040 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Extron DMP 128 Plus C below.

What is the weight of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a weight of 2040 g.

What is the height of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a height of 43 mm.

What is the width of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a width of 442 mm.

What is the depth of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a depth of 241 mm.

Is the manual of the Extron DMP 128 Plus C available in English?

Yes, the manual of the Extron DMP 128 Plus C is available in English .

Is your question not listed? Ask your question here

No results