Extron DMP 128 Plus C manual

Extron DMP 128 Plus C
8.4 · 1
PDF manual
 · 188 pages
English
manualExtron DMP 128 Plus C
DMP 128 Plus • Remote Control and Configuration 125

Establishing a Network Connection via LAN

1. Open a TCP socket to port 23 using the DMP 128 Plus IP address.
NOTE: If the local system administrators have not changed the value, the factory
specified default, 192.168.254.254, is the correct value for this field.
2. The DMP 128 Plus responds with a copyright message including the date, the name of
the product, firmware version, part number, and the current date/time.
3. If the device is password protected, enter the appropriate administrator or user
password.
a. If the password is accepted, the device responds with Login User or Login
Administrator.
b. If the password is not accepted, the Password prompt reappears.
NOTES:
The Ethernet link times out after a designated period of time of no communications.
By default, the timeout value is set to 5 minutes and can be changed (see Set
global IP port timeout on page129).
Extron recommends leaving the default timeout at 5 minutes and periodically
issuing the Query (Q) command to keep the connection active. If there are long idle
periods, disconnect the socket and reopen the connection when another command
must be sent.

USB Config Port

The DMP 128 Plus has a front panel USB port that can be connected to a computer as a
host device running either the HyperTerminal or DataViewer utilities for control of the device.
Once a connection is established, SIS programming can begin (see Host-to-Device
Communications on the next page).

Verbose Modes

Telnet connections are used to monitor changes that occur, such as commands from
other Telnet sockets or a serial port. For a Telnet session to receive change notices, the
Telnet session must be in verbose mode 1 or 3 (see Set verbose mode on page132).
In verbose mode 1 or 3, the Telnet socket reports changes in messages that resemble SIS
command responses.

Tagged and Untagged Responses

When a query command is sent in verbose mode 0 or 1, only the “untagged” value is
returned. When a query command is sent in other verbose modes, the response is “tagged”
and resembles the response to a set command.
Examle: The gain query command EG40000AU} is sent. The following responses
appear depending on the verbose mode:
Untagged (verbose 0 or 1): 626], just the gain value with no other information.
Tagged (verbose 2 or 3): DsG40000*626], the type of query sent, the OID queried,
and the gain value.
NOTE: All query responses listed in this guide are untagged.

Manual

View the manual for the Extron DMP 128 Plus C here, for free. This manual comes under the category not categorized and has been rated by 1 people with an average of a 8.4. This manual is available in the following languages: English. Do you have a question about the Extron DMP 128 Plus C or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Extron and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Extron DMP 128 Plus C specifications

Below you will find the product specifications and the manual specifications of the Extron DMP 128 Plus C.

General
BrandExtron
ModelDMP 128 Plus C | 60-1512-01
Productnot categorized
EAN5711783372820
LanguageEnglish
FiletypeUser manual (PDF)
Ports & interfaces
Number of inputs12 inputs
Features
Total Harmonic Distortion plus Noise (THD+N)0.01 %
Frequency range20 - 20000 Hz
Signal-to-Noise Ratio (SNR)115 dB
Input impedance10000 Ω
Housing colorGray
Housing materialMetal
Power
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Power consumption (typical)29.4 W
Operational conditions
Operating temperature (T-T)0 - 50 °C
Storage temperature (T-T)-40 - 70 °C
Operating relative humidity (H-H)10 - 90 %
Storage relative humidity (H-H)10 - 90 %
Weight & dimensions
Width442 mm
Depth241 mm
Height43 mm
Weight2040 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Extron DMP 128 Plus C below.

What is the weight of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a weight of 2040 g.

What is the height of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a height of 43 mm.

What is the width of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a width of 442 mm.

What is the depth of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a depth of 241 mm.

Is the manual of the Extron DMP 128 Plus C available in English?

Yes, the manual of the Extron DMP 128 Plus C is available in English .

Is your question not listed? Ask your question here

No results