Extron DMP 128 Plus C manual

Extron DMP 128 Plus C
8.4 · 1
PDF manual
 · 188 pages
English
manualExtron DMP 128 Plus C
DMP 128 Plus • Dante Controller 117

Redundant Configuration

In redundant mode, the 4-port AT switch acts as two separate 2-port switches that
duplicate audio traffic. Ports 3 and 4 are marked (PRI) for primary while ports 1 and 2
are marked (SEC) for secondary (see figure 189 below). Primary and secondary switches
cannot be connected together anywhere in the audio network. Redundant configuration can
be enabled using Dante Controller or DSP Configurator.
100-240V 0.7A MAX
50 - 60 Hz
LAN
DMP 128 Plus C AT
INPUTS
RxTx G
RS-232
+S+V -S G
GIN
1
O1 O2 GIN
2
O1 O2 GIN
3
O1 O2 GIN
4
O1 O2 GIN
5
O1 O2 GIN
6
O1 O2 GIN
7
O1 O2 GIN
8
O1 O2
56
78
11 12
1 2
3
4
9
10
1 2 3
4 5 6 7 8
I/O
OUTPUTS
DMP EXP
ACP
REMOTE
USB AUDIO
RESET
AT
1
(SEC)
2
3
4
(PRI)
Secondary PortsPrimary Ports
Figure 189. Primary and Secondary AT Ports
To configure the DMP 128 Plus in redundant mode using Dante Controller:
1. Open Dante Controller.
2. Press <Ctrl+D> on the keyboard to access the Device View dialog box.
3. Select the desired DMP 128 Plus AT from the (Choose a Dante Device...)
drop-down menu (see figure 190,
1
below).
4. Select the Network Config tab (
2
).
5. From the Dante Redundancy panel, use the drop-down to select Redundant (
3
).
Figure 190. Redundant Mode Configuration in Dante Controller
figure 189 Primary and Secondary Ports
figure 190 Redundant config in Dante Cont

Manual

View the manual for the Extron DMP 128 Plus C here, for free. This manual comes under the category not categorized and has been rated by 1 people with an average of a 8.4. This manual is available in the following languages: English. Do you have a question about the Extron DMP 128 Plus C or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Extron and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Extron DMP 128 Plus C specifications

Below you will find the product specifications and the manual specifications of the Extron DMP 128 Plus C.

General
BrandExtron
ModelDMP 128 Plus C | 60-1512-01
Productnot categorized
EAN5711783372820
LanguageEnglish
FiletypeUser manual (PDF)
Ports & interfaces
Number of inputs12 inputs
Features
Total Harmonic Distortion plus Noise (THD+N)0.01 %
Frequency range20 - 20000 Hz
Signal-to-Noise Ratio (SNR)115 dB
Input impedance10000 Ω
Housing colorGray
Housing materialMetal
Power
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Power consumption (typical)29.4 W
Operational conditions
Operating temperature (T-T)0 - 50 °C
Storage temperature (T-T)-40 - 70 °C
Operating relative humidity (H-H)10 - 90 %
Storage relative humidity (H-H)10 - 90 %
Weight & dimensions
Width442 mm
Depth241 mm
Height43 mm
Weight2040 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Extron DMP 128 Plus C below.

What is the weight of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a weight of 2040 g.

What is the height of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a height of 43 mm.

What is the width of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a width of 442 mm.

What is the depth of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a depth of 241 mm.

Is the manual of the Extron DMP 128 Plus C available in English?

Yes, the manual of the Extron DMP 128 Plus C is available in English .

Is your question not listed? Ask your question here

No results