Extron DMP 128 Plus C manual

Extron DMP 128 Plus C
8.4 · 1
PDF manual
 · 188 pages
English
manualExtron DMP 128 Plus C
DMP 128 Plus • Dante Controller 110

Configuring the DMP 128 Plus AT in Dante Controller

Use a standard Ethernet cable to connect the DMP 128 Plus AT to a Dante network via the
rear panel AT port (see figure 2,
I
on page5) and power the device.

Device Name

Multiple devices on the same Dante network can present difficulty in identifying individual
devices. To avoid confusion and difficulty, ensure the following steps are taken:
Connect devices to the Dante network one at a time.
Rename each device before making audio connections in Dante Controller.
Rename each device with a unique and meaningful identifier.
Rename each device before the next device is connected to the Dante network.
ATTENTION: It is essential that a Dante device be named before audio subscriptions
with other devices are established. Existing subscriptions are removed when a device
is renamed.
In Dante Controller, a device can be renamed to identify the device on the audio network.
The default device name of the DMP 128 Plus AT consists of the model name, followed by
the last six characters of the Dante interface MAC address (for example, DMP128P-0ee8ee).
In addition to renaming the device, individual Transmitter (Tx) and Receiver (Rx) channels
can be renamed.
The Dante device name must be set before making any connections to other devices on the
Dante network. Renaming a device after making connections removes existing connections
to and from that device. Refer to Renaming the DMP 128 Plus AT in Dante Controller
on the next page for renaming procedure.

Receiver and Transmitter Names

In addition to renaming a device, individual transmitter and receiver channels can be
renamed in Dante Controller. Rename transmitter and receiver channels to reflect the
location of the device or the purpose of the transmitter or receiver. Ensure transmitter and
receiver channels are renamed before making audio connections between devices. Refer to
Renaming a Receiver or Transmitter on page113 for renaming procedure.

Dante Controller Naming Conventions

Device names follow Domain Name System (DNS) hostname rules. Legal characters are
A-Z, a-z, 0-9, and hyphen (-). Names must begin with a letter and cannot end with a
hyphen (-).
Dante Tx and Rx channel names (also known as labels) can be up to 31 characters in
length. Label names are not case-sensitive. For example, “ANALOG OUT-1” and “analog
out-1” are recognized as the same name. Unicode and non-roman characters are not
supported.
Tx and Rx channel labels can use any character except equals (=), period (.), or @.
Tx and Rx channel labels must be unique on a device but do not need to be unique on
the network.

Manual

View the manual for the Extron DMP 128 Plus C here, for free. This manual comes under the category not categorized and has been rated by 1 people with an average of a 8.4. This manual is available in the following languages: English. Do you have a question about the Extron DMP 128 Plus C or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Extron and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Extron DMP 128 Plus C specifications

Below you will find the product specifications and the manual specifications of the Extron DMP 128 Plus C.

General
BrandExtron
ModelDMP 128 Plus C | 60-1512-01
Productnot categorized
EAN5711783372820
LanguageEnglish
FiletypeUser manual (PDF)
Ports & interfaces
Number of inputs12 inputs
Features
Total Harmonic Distortion plus Noise (THD+N)0.01 %
Frequency range20 - 20000 Hz
Signal-to-Noise Ratio (SNR)115 dB
Input impedance10000 Ω
Housing colorGray
Housing materialMetal
Power
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Power consumption (typical)29.4 W
Operational conditions
Operating temperature (T-T)0 - 50 °C
Storage temperature (T-T)-40 - 70 °C
Operating relative humidity (H-H)10 - 90 %
Storage relative humidity (H-H)10 - 90 %
Weight & dimensions
Width442 mm
Depth241 mm
Height43 mm
Weight2040 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Extron DMP 128 Plus C below.

What is the weight of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a weight of 2040 g.

What is the height of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a height of 43 mm.

What is the width of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a width of 442 mm.

What is the depth of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a depth of 241 mm.

Is the manual of the Extron DMP 128 Plus C available in English?

Yes, the manual of the Extron DMP 128 Plus C is available in English .

Is your question not listed? Ask your question here

No results