Extron DMP 128 Plus C manual

Extron DMP 128 Plus C
8.4 · 1
PDF manual
 · 188 pages
English
manualExtron DMP 128 Plus C
DMP 128 Plus • Configuration Tools 94

Expansion Bus

With the Extron Expansion (EXP) port, two EXP-enabled devices can be connected for
bidirectional streaming of up to 16 channels of audio. EXP inputs and outputs contain DSP
(see Expansion and AT Inputs on page53 and Expansion Outputs on page65).

Connecting the EXP Ports

When connecting a DMP 128 Plus to another EXP-enabled device for EXP communication,
one of the devices must be set as the primary unit. The primary unit serves as the master
clock for all EXP audio communication. The other unit must be set as a secondary unit in
order for a connection to be established.
There are two different procedures for setting up DMP 128 Plus for EXP communication.
The first procedure describes how to set up a DMP 128 Plus non-AT model with another
EXP-enabled non-AT device for EXP communication (see Connecting a DMP 128 Plus
non-AT with Another EXP-Enabled non-AT Device below).
The second procedure describes how to set up a DMP 128 Plus AT model with another
EXP-enabled non-AT device for EXP communication (see Connecting a DMP 128 Plus AT
Device and an EXP-enabled non-AT Device on page95on the next page).
NOTE: Two DMP 128 Plus AT models cannot be connected via the EXP port because
AT models can only be configured as a primary unit and cannot be set as a secondary
unit. Instead, use the rear panel AT switch to connect the two devices over a Dante
network (see Dante Controller on page107).

Connecting a DMP 128 Plus non-AT with Another EXP-Enabled non-AT

Device

The DMP 128 Plus can be connected to either a DTP CrossPoint or another DMP128Plus
via EXP. The following procedure describes connecting a DMP 128 Plus non-AT with either a
DTP CrossPoint or another DMP 128 Plus non-AT model.
1. Connect live to the DMP 128 Plus.
NOTE: If connecting to DMP 128 Plus devices, decide which device will be set as
primary unit and connect Live to that device.
2. Select Tools > Expansion Bus > Primary Unit.
3. Connect Live to the other DMP 128 Plus. If connecting a DTP CrossPoint, proceed to
step 5.
4. Select Tools > Expansion Bus and ensure Secondary Unit is selected.
NOTE: If both devices are configured as primary or secondary, an EXP connection
cannot be established.
5. Use a CAT 6 cable (such as the 1 foot cable included with the DMP 128 Plus) to
connect the two rear panel EXP ports.
6. When the connection is established, the front panel EXP LED on the primary
DMP128Plus lights steadily and the EXP LED on the secondary unit blinks rapidly.
NOTE: The DTP CrossPoint EXP LED is located on the rear panel next to the EXP
port.

Manual

View the manual for the Extron DMP 128 Plus C here, for free. This manual comes under the category not categorized and has been rated by 1 people with an average of a 8.4. This manual is available in the following languages: English. Do you have a question about the Extron DMP 128 Plus C or do you need help? Ask your question here

Index

Need help?

Do you have a question about the Extron and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Extron DMP 128 Plus C specifications

Below you will find the product specifications and the manual specifications of the Extron DMP 128 Plus C.

General
BrandExtron
ModelDMP 128 Plus C | 60-1512-01
Productnot categorized
EAN5711783372820
LanguageEnglish
FiletypeUser manual (PDF)
Ports & interfaces
Number of inputs12 inputs
Features
Total Harmonic Distortion plus Noise (THD+N)0.01 %
Frequency range20 - 20000 Hz
Signal-to-Noise Ratio (SNR)115 dB
Input impedance10000 Ω
Housing colorGray
Housing materialMetal
Power
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Power consumption (typical)29.4 W
Operational conditions
Operating temperature (T-T)0 - 50 °C
Storage temperature (T-T)-40 - 70 °C
Operating relative humidity (H-H)10 - 90 %
Storage relative humidity (H-H)10 - 90 %
Weight & dimensions
Width442 mm
Depth241 mm
Height43 mm
Weight2040 g
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Extron DMP 128 Plus C below.

What is the weight of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a weight of 2040 g.

What is the height of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a height of 43 mm.

What is the width of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a width of 442 mm.

What is the depth of the Extron DMP 128 Plus C?

The Extron DMP 128 Plus C has a depth of 241 mm.

Is the manual of the Extron DMP 128 Plus C available in English?

Yes, the manual of the Extron DMP 128 Plus C is available in English .

Is your question not listed? Ask your question here

No results