Electro Harmonix Worm Modulation Multi FX manual

Electro Harmonix Worm Modulation Multi FX
(1)
  • Number of pages: 1
  • Filetype: PDF

The Worm

Analog Modulation Pedal

Congratulations on your purchase of
The Worm
, a multi-functional modulation pedal.
The Worm
is four analog effects in one: Modulated Wah, Phaser, Tremolo and Vibrato.
-AC ADAPTOR-
Your
Worm
comes equipped with a 24 volt DC (inner positive) / 100mA external power
adapter. Use only the power adapter that is supplied! Using the wrong adapter can cause
serious bodily injury and may damage your unit. This will void the warranty.
- CONTROLS -
MODE Rotary Switch
– Selects between the four different types of effects:
WAH
,
PHASER
,
TREMOLO
and
VIBRATO
.
RANGE Knob
– Adjusts the amount of effect that will be applied to your signal. As
the
RANGE
knob is turned from the Counter-Clockwise (minimum) position to the
Clockwise (maximum) position, the intensity of the effect will increase.
RATE Knob
– Adjusts the speed of modulation for the effect. As the
RATE
knob is
turned from the Counter-Clockwise (minimum) position to the Clockwise (maximum)
position, the speed of the effect will go from slow to fast.
AUTO / MANUAL/EXP Toggle Switch
– Set this switch to AUTO mode for normal
modulation use. When this switch is set to MANUAL/EXP mode, the internal
modulation waveform is disconnected from the circuit and the RANGE knob will
sweep through the effect. In addition, while in MANUAL/EXP mode, you can connect
an expression pedal or control voltage (between 0 – 5V only) to the EXP. PEDAL jack
and use the expression pedal to sweep the effects.
STATUS LED and FOOTSWITCH
– If the effect is engaged, the LED will blink at
the same rate that the effect modulates. If the LED is off, The Worm is in True
Bypass mode. The footswitch engages/disengages the effect.
- JACKS -
INPUT Jack
– Connect your instrument to this jack. The input impedance present at
this jack is 300 k
.
OUTPUT Jack
– Connect this jack to your amp or next effects pedal. The output
impedance present at this jack is 1 k
.
EXP. PEDAL Jack
– Connect an Expression Pedal to this jack or the output from a
Control Voltage generator. The expression pedal must have a TRS plug attached to it
with the tip attached to the pedal’s wiper. The control voltage must be between 0V
and 5V. The input impedance present at this jack is 100 k
.
Acceptable expression pedals include: M-Audio EX-P, Moog Expression Pedal, Roland
EV-5 and Boss FV-500L.
24V PWR Jack
– Connect the output plug from the supplied 24VDC/100mA wall
wart to the 24V PWR jack at the top of The Worm. Please use only the AC Adapter
that came supplied with The Worm. The Worm does not accept batteries.
Electro Harmonix Worm Modulation Multi FX

Need help?

Number of questions: 0

Do you have a question about the Electro Harmonix Worm Modulation Multi FX or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Electro Harmonix Worm Modulation Multi FX owners to properly answer your question.

View the manual for the Electro Harmonix Worm Modulation Multi FX here, for free. This manual comes under the category Not categorized and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Electro Harmonix Worm Modulation Multi FX or do you need help? Ask your question here

Electro Harmonix Worm Modulation Multi FX specifications

General
Brand Electro Harmonix
Model Worm Modulation Multi FX
Product Not categorized
Language English
Filetype PDF

Frequently Asked Questions

Below, you will find the most frequently asked questions about the Electro Harmonix Worm Modulation Multi FX.

Is your question not listed? Ask your question here