Electro Harmonix Grand Canyon manual

Electro Harmonix Grand Canyon
7.5 · 1
PDF manual
 · 36 pages
English
manualElectro Harmonix Grand Canyon

1

GRAND CANYON

Multifunction Delay & Looper

Congratulations on your purchase of the Grand Canyon, a superior sounding,
massively powerful Delay and Looper pedal. Within the Grand Canyon are a vast
array of awe-inspiring effects. Explore a wide range of delays and textures,
including pristine or bitcrushed digital, exquisite Deluxe Memory Man, rhythmic
drum, warm tape, plate reverb, polyphonic pitch shift, and ethereal shimmer. The
Grand Canyon even has a full-featured looper which can be used simultaneously
with any of the delay effects to conjure lush, layered soundscapes. Fine tune the
effects with a broad array of intuitive controls, and you’re in for a truly inspiring
and grand experience.
WARNING: Your Grand Canyon comes equipped with an Electro-Harmonix 9.6DC-200BI
power supply. The Grand Canyon requires 150mA at 9VDC with a center negative plug.
Use of the wrong adapter or a plug with the wrong polarity may damage your Grand
Canyon and void the warranty. Do not exceed 10.5VDC on the power plug. Power supplies
rated for less than 150mA will cause the Grand Canyon to act unreliably.

- FEATURES -

12 Delay Types yield a wide range of delay and echo effects
Up to 3 seconds of delay time
TAP footswitch with 9 Tap Divide settings for precise delay times
Stereo output produces stereo delay and ping pong effects
Up to 16 minutes of recording time on the full-featured looper which includes
unlimited overdubs, undo/redo, a dedicated stop button, loop fade-out,
reverse, and speed adjustment
The Looper can record and overdub the internal stereo delay effects
Loop audio remains in the Grand Canyon until you erase it, even after removing
power from the unit
Easy pushbutton access to extra features like delay tails, momentary effect
mode, and ping-pong output
13 Presets may be saved and recalled: one preset for each delay type and one
for the looper
Programmable expression pedal settings allow you to control any combination
of the Grand Canyon’s knobs with an external expression pedal
Connector for external 1-, 2- or 3-button footswitch allows for added control
High quality buffered analog bypass and soft switching

View the manual for the Electro Harmonix Grand Canyon here, for free. This manual comes under the category not categorized and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Electro Harmonix Grand Canyon or do you need help? Ask your question here

Need help?

Do you have a question about the Electro Harmonix and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

The Electro Harmonix Grand Canyon is a multi-function delay and looper pedal designed for guitarists seeking versatile effects. This pedal offers a range of delay types and controls, including tap tempo, modulation, and expression pedal input. The Grand Canyon also features a built-in looper with up to 16 minutes of recording time. With stereo input and output, this pedal can be used in a variety of setups for enhanced sound quality. The Grand Canyon is housed in a sturdy and compact enclosure, making it suitable for use on stage or in the studio. With its wide range of features and high-quality construction, this pedal is a reliable option for musicians looking to expand their sonic capabilities.

General
BrandElectro Harmonix
ModelGrand Canyon
Productnot categorized
LanguageEnglish
FiletypeUser manual (PDF)

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Electro Harmonix Grand Canyon below.

How do I quickly set up the Electro Harmonix Grand Canyon?

To quickly set up the Electro Harmonix Grand Canyon, follow these steps: 1. Plug in the supplied EHX9.6DC AC Adapter into the 9V jack at the top of the Grand Canyon. Then, plug the AC Adapter into an AC outlet. 2. Connect your guitar or other instrument into the INPUT jack using a standard 1/4” instrument cable. Connect the L OUT jack to your amp with another standard 1/4” instrument cable. 3. For stereo operation, connect R OUT to another amp. To dial in a standard digital delay effect: 1. Make sure none of the buttons at the top left of the Grand Canyon, like TAILS, are lit. If any button is lit, press the button once to disable it. 2. Ensure that only the DELAY mode LED is lit. If the LOOPER LED is lit, press the small white Mode button located near the DELAY and LOOPER LEDs until only DELAY is lit. 3. Rotate the DELAY TYPE knob clockwise to the ECHO setting for a standard digital delay. 4. Set the two smaller knobs to the right of the DELAY TYPE knob to their middle positions. 5. Adjust the number of repeats with the FEEDBACK knob, the delay time with the DELAY knob, and the delay volume with the DELAY LVL knob. These steps should help you quickly set up the Electro Harmonix Grand Canyon for your desired delay effect.

What do the different controls and LEDs on the Electro Harmonix Grand Canyon do?

The controls and LEDs on the Electro Harmonix Grand Canyon serve different functions. Here is a breakdown of what each control and LED does: 1. DELAY / LOOPER MODES, BUTTON, AND LEDS: - The Grand Canyon has three functional modes: Delay, Delay+Looper, and Looper. - The small white Mode button and two LEDs labeled DELAY and LOOPER allow you to switch between these modes. - In DELAY mode, the DELAY LED is lit, and all controls modify the delay effects according to the red labels. - In DELAY+LOOPER mode, both the DELAY and LOOPER LEDs are lit. The delay effects are still active, and the TAP/LOOP footswitch handles various looper functions. - In LOOPER mode, the LOOPER LED is lit, and the delay effects are deactivated. The four white knobs control the looper functions, and the TAP/LOOP footswitch handles looper functions. 2. LOOP LVL KNOB: - In DELAY mode, the LOOP LVL knob sets the loop volume if a loop is playing back. 3. TAP/LOOP FOOTSWITCH: - In DELAY mode, the TAP/LOOP footswitch works as a tap tempo button. Press and hold it to ramp up to maximum feedback. - In DELAY+LOOPER mode, the TAP/LOOP footswitch handles various looper functions such as Play, Record, Overdub, Undo, Redo, Stop, and Erase. - In LOOPER mode, the TAP/LOOP footswitch also handles looper functions. 4. BYPASS/STOP FOOTSWITCH: - In DELAY mode, the BYPASS/STOP footswitch toggles between effect and bypass modes. - In DELAY+LOOPER mode, the BYPASS/STOP footswitch toggles between effect and bypass modes for the delay effect and can function as a tap tempo switch. - In LOOPER mode, the BYPASS/STOP footswitch stops the loop with one press. These controls and LEDs allow you to navigate and control the different modes and functions of the Electro Harmonix Grand Canyon.

How do I switch between Delay and Looper modes on the Electro Harmonix Grand Canyon?

To switch between Delay and Looper modes on the Electro Harmonix Grand Canyon, follow these steps: 1. Locate the small white Mode button on the Grand Canyon. 2. Press the Mode button once to cycle between the different modes. 3. The DELAY LED indicates that you are in Delay mode, where you can access and adjust the delay effects. 4. The DELAY+LOOPER LED indicates that you are in Delay+Looper mode, where both the delay effects and looper functions are active. 5. The LOOPER LED indicates that you are in Looper mode, where the delay effects are deactivated, and you can use the Grand Canyon as a standalone looper. 6. To switch directly from Looper mode to Delay+Looper mode, double-tap the Mode button. By following these steps, you can easily switch between the Delay and Looper modes on the Electro Harmonix Grand Canyon to access the desired functionality.

What do the control knobs on the Electro Harmonix Grand Canyon adjust?

The control knobs on the Electro Harmonix Grand Canyon adjust different parameters depending on the mode. Here is a breakdown of what each control knob does: In Delay Mode: 1. DELAY LVL: Controls the balance between your dry signal and the delay effects. Turning it up increases the volume of the delay output. 2. LOOP LVL*: Controls the loop volume if a loop was playing before entering Delay Mode. 3. FEEDBACK: Controls the number of repeats of the delayed signal. 4. DELAY: Controls the delay time. Turning it clockwise increases the delay time. In Delay+Looper Mode: 1. DELAY LVL: Same as in Delay Mode. 2. LOOP LVL: Controls the output volume of the looper's playback. 3. FEEDBACK: Same as in Delay Mode. 4. DELAY: Same as in Delay Mode. In Looper Mode: 1. DRY CUT: Works as a reverse volume control for your dry signal. 2. LOOP LVL: Controls the output volume of the looper's playback. 3. DUB LVL: Acts as a feedback control for the looper while overdubbing. 4. FADEOUT: Sets the fadeout time of the loop when stopped. These control knobs allow you to adjust various parameters and customize your sound when using the Electro Harmonix Grand Canyon.

How do I effectively use the Looper mode on the Electro Harmonix Grand Canyon?

To effectively use the Looper mode on the Electro Harmonix Grand Canyon, follow these steps: 1. Enter Looper mode by pressing the small white Mode button until the LOOPER LED is lit. 2. To record a loop, ensure that no loop is in memory (MEM LED is off) and press the TAP/LOOP footswitch once. The REC LED will light up, indicating that recording has started. 3. To stop recording and set the loop length, press the TAP/LOOP footswitch again. The MEM and PLAY LEDs will light up, and the loop will begin playing immediately. 4. Adjust the output level of the loop playback using the LOOP LVL knob. 5. While playing the loop, the PLAY LED will blink each time the loop cycles. 6. To start loop playback, ensure that a loop is in memory (MEM LED is lit and PLAY LED is off) and press and release the TAP/LOOP footswitch once. The PLAY LED will light up, indicating that the loop is playing. 7. To stop loop playback, double-tap the TAP/LOOP footswitch quickly. Alternatively, if you are in Looper-only mode, press and release the BYPASS/STOP footswitch once. 8. The loop playback can either stop immediately or fade out, depending on the setting of the FADEOUT knob. Turn the FADEOUT knob clockwise for longer fadeout times. 9. To change the direction of loop playback, use the REVERSE knob. Turning it fully counterclockwise reverses the loop's direction, while turning it above 9 o'clock plays the loop in the forward direction. 10. Adjust the playback speed of the loop using the SPEED knob. Turning it counterclockwise slows down the loop, while turning it clockwise speeds it up. By following these steps, you can effectively use the Looper mode on the Electro Harmonix Grand Canyon to create and control loops with various settings.

Is the manual of the Electro Harmonix Grand Canyon available in English?

Yes, the manual of the Electro Harmonix Grand Canyon is available in English .

Is your question not listed? Ask your question here

No results