View the manual for the Easy Home GT-SI-lcd-03-IT here, for free. This manual comes under the category irons and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Easy Home GT-SI-lcd-03-IT or do you need help? Ask your question here
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Easy Home GT-SI-lcd-03-IT below.
A high wattage iron heats up faster.
Soak a cloth in vinegar and put your iron on the cloth for half an hour so that the vinegar can absorb into the stains. You can then remove the stains with a damp cloth.
Yes, irons are in principle only suitable for tap water.
To adjust the steam emission level on the Easy Home GT-SI-lcd-03-IT iron, follow these steps: 1. Heat up the iron by switching it on and allowing it to reach the desired temperature. 2. Choose the heat setting that corresponds to the fabric type and the care label of the clothing or textile you are ironing. Do not exceed the manufacturer's recommendation. 3. Hold the iron in a level position, and steam will be emitted from the soleplate. 4. To decrease the steam emission level, turn the steam control dial clockwise. 5. To increase the steam emission level, turn the steam control dial counterclockwise. 6. Use the steam burst function when the heat setting is at 6 or higher to smooth out stubborn folds. Be cautious not to use the steam burst function on sensitive fabric types like polyacrylics or acetate polyamide blended fabrics. Remember to always follow the care instructions for your garments and avoid ironing at excessively high temperatures to prevent damage.
If your Easy Home GT-SI-lcd-03-IT iron is not producing steam, there are a few possible reasons and steps you can take to troubleshoot the issue: 1. Check the plug: Ensure that the iron is properly plugged into the socket. If the plug is loose or not inserted correctly, it may prevent the iron from functioning. 2. Heat setting: Make sure you have selected an appropriate heat setting for steam production. If the temperature is set too low, the iron may not generate enough heat to produce steam. Adjust the heat setting accordingly. 3. Water level: Check if the water tank is filled with water. If the tank is empty or the water level is too low, the iron will not be able to generate steam. Fill the tank with water as per the instructions in the manual. 4. Steam control dial: Verify that the steam control dial is set to an appropriate level. If the dial is set too high or too low, it may affect the steam production. Adjust the dial to the desired steam pressure. 5. Anti-drip function: If you hear clicking noises from the iron, it indicates that the anti-drip function is active. This is not a malfunction but a safety feature to prevent water leakage. Ensure that the iron is positioned correctly to avoid any water leakage. If you have followed these steps and the issue persists, it is recommended to contact the manufacturer's service center for further assistance. You can find the contact details on the warranty card provided with the iron.
To clean the steam emission holes in the soleplate of the Easy Home GT-SI-lcd-03-IT iron, follow these steps: 1. Unplug the iron from the socket and allow it to cool down completely. 2. Fill the tank with water up to the maximum fill mark. 3. Plug the iron back into a suitable socket with an earthing contact. 4. Turn the steam control dial to the highest position. 5. Set the heat to the recommended level. 6. Wait for the iron to reach the operating temperature, indicated by an acoustic signal. 7. Hold the iron over a sink or an absorbent cloth. 8. Turn the steam control dial counterclockwise to the maximum position. 9. Water and steam will be emitted from the steam emission holes in the soleplate. 10. Tilt the iron to remove any deposits in the tank and flush them out. 11. After approximately 10 seconds, turn the steam control dial back to the highest position. 12. Repeat steps 4 to 11 if there are still deposits in the tank. 13. Place the iron on the heel rest and allow it to cool down completely. By following these steps, you can effectively clean the steam emission holes in the soleplate of the Easy Home GT-SI-lcd-03-IT iron.
Yes, the manual of the Easy Home GT-SI-lcd-03-IT is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the Easy Home and is the answer not in the manual?
Question and answer
Number of questions: 0