View the manual for the E-flite Timber X here, for free. This manual comes under the category radio controlled toys and has been rated by 1 people with an average of a 8.7. This manual is available in the following languages: English. Do you have a question about the E-flite Timber X or do you need help? Ask your question here




Below you will find the product specifications and the manual specifications of the E-flite Timber X.
The E-flite Timber X is a radio controlled toy that measures 1055 millimeters in length and weighs 1698 grams. It comes with a remote control, offering 6 channels for easy maneuverability. With a wingspan of 1200 millimeters, this toy delivers a thrilling flying experience. Equipped with a brushless motor, the E-flite Timber X delivers powerful performance. It requires a 3–4S LiPo battery with a capacity of 3200 milliampere-hours. Recommended batteries for this toy include the EFLB22003S30 and EFLB22004S30. Some assembly is required to get this toy up and running, with an estimated assembly time of 60 minutes. It also requires one battery, supporting only one battery at a time. Users should note that batteries are not included and need to be purchased separately. The E-flite Timber X features a generous wing area of 3400 square centimeters, providing stability and control during flight. This toy offers an exciting and engaging experience for hobbyists and enthusiasts. Note: The above description is based solely on the provided specifications. It does not include personal opinions or subjective evaluation of the product.

| Brand | E-flite |
| Model | Timber X | EFL3850 |
| Product | radio controlled toy |
| EAN | 0605482207611 |
| Language | English |
| Filetype | User manual (PDF) |
| Length | 1055 mm |
| Weight | 1698 g |
| Wingspan | 1200 mm |
| Handheld remote control | Yes |
| Assembly time | 60 min |
| Channels quantity | 6 channels |
| Motor type | Brushless |
| Assembly required | Yes |
| Wing area | 3400 cm² |
| Product type | Airplane |
| Replica | No |
| Construction type | Bind-N-Fly (BNF) |
| Engine type | Electric engine |
| Battery capacity | 3200 mAh |
| Battery type | 3–4S LiPo |
| Recommended battery | EFLB22003S30, EFLB22004S30 |
| Batteries required | Yes |
| Number of batteries supported | 1 |
| Product color | Green, Grey, White |
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the E-flite Timber X below.
The E-flite Timber X has a weight of 1698 g.
The product can still be used safely after proper cleaning. Remove the battery with gloves and clean the battery compartment with a toothbrush and vinegar. After drying, new batteries can be inserted into the device.
Make sure both the transmitter and the aircraft are turned off. Then, turn on the transmitter and activate "bind mode" following the specific instructions for your transmitter. Finally, power on the aircraft while keeping it within close range of the transmitter until the binding process is complete.
The E-flite Timber X is compatible with a 3S or 4S LiPo battery. It is recommended to use a battery with a minimum capacity of 2200mAh and a discharge rate of at least 30C for optimal performance.
To adjust the control surface throws, locate the control horns on each control surface. Use the provided wrench to loosen the screws holding the control horn in place, then reposition the control horn in a different hole to achieve the desired throw. Tighten the screws securely once the desired adjustment is made.
If you notice the aircraft pulling to one side or not flying level, you can utilize the trim knobs located on the transmitter. Use the aileron, elevator, and rudder trim knobs to make small adjustments until the aircraft behaves level and straight during flight.
To perform a CG check, first ensure the aircraft is in a powered-off state. Hold the aircraft securely at the CG point specified in the manual (typically indicated by a mark on the wing or fuselage). The aircraft should balance level or slightly nose-down. Make adjustments by shifting the battery or adding weight until the desired CG is achieved for stable and predictable flight performance.
Yes, the E-flite Timber X comes with a remote control. This means that users can easily control the toy and perform different maneuvers with it.
The E-flite Timber X has 6 channels. This provides users with a versatile control system, allowing for a wide range of movements and functionalities.
The wingspan of the E-flite Timber X is 1200 mm. This size ensures stability and agility during flight, providing a satisfying experience for the user.
Yes, the E-flite Timber X requires assembly. This gives users the opportunity to customize and personalize their toy before using it.
The E-flite Timber X has a brushless motor. Brushless motors are known for their efficiency, power, and durability, making the E-flite Timber X a high-performance toy compared to others with different motor types.
Yes, the manual of the E-flite Timber X is available in English .
Is your question not listed? Ask your question here
No results
Need help?
Do you have a question about the E-flite and is the answer not in the manual?
Question and answer
Number of questions: 1PROP